Search results for: 'santex co'

REFERENCE NUMBER: M-4136 SANTEX TENTER FRAME YEAR 2003-UP TO 3400mm – 3 ZONE – VERTICAL PIN – HOT OIL TYPE: SANTEX TENTER FRAME YEAR: 2003 WORKING WIDTH: 800mm UP TO 3400mm SPEED: 2 UP TO 20 M/MIN CHAIN: VERTICAL PIN CHAIN DRYER: 3 COMPARTMENTS DRYER LENGTH: 6 METERS MAX. TEMP.: 230° C HEATING: DIATHERMIC OIL OIL BOILER: GARIONI NAVAL TH 500 CAPACITY: 581 KW, MAX. TEMP. 350° C, NITROGEN COVERED TOTAL LENGTH NEEDED: APPROX. 20,000mm TOTAL WIDTH OF MACHINE: 6,200mm TOTAL HEIGHT OF MACHINE: 3,100mm ENTRY COMBINATION GUIDING CHAIN FOR A-FRAMES CORRECT POSITIONING RUBBERIZED ROLLERS AS INFEED UNIT WECO IMPREGNATION UNIT, CONTROL AND TANK ROLLER WITH LOAD CELL MAHLO WEFT STRAIGHTENER, TYPE: RFMC-10A 6 MEASURING HEADS, WW 4200mm OPERATION PEDESTAL OPERATION PANEL, MONITOR 1 UPPER INFEED ROLLER + 1 BENDED ROLLER E+L FABRIC INFEED VERTICAL PIN CHAIN 3 SECTIONAL DRYER (6 M) COOLING UNIT AT EXIT 2 CAMERAS VIDEO CONTROL STRETCH WORK: 2 PRESSING ROLLERS 3 HEATED DRAG ROLLERS WITH SINGLE DRIVE TEMPERATURE 80° C TO 250° C ON-WINDING UNIT FOR A-FRAMES ELECTRICAL CABINET QUANTITY AVAILABLE: 1 Learn More

J-5305 FINISHING PLANT FOR WORSTED AND WOOLEN SPLIT SALE POSSIBLE Learn More

SANTEX 4 ROLL THERMOBONDING CALANDER, WIDTH 2800mm, YEAR 2002

YEAR: 2002

WIDTH: 2800mm

4 ROLL

NO HEATING INCLUDED

WAS USED AS A COOLING CALANDER

ABLE TO CONNECT TO A HEATING UNIT (WITH 2 HEATED ROLLERS)

 

Learn More

M-6248 SANTEX DRYER YEAR 1997 WIDTH 2400mm

DRYING MACHINE
MAKE: SANTEX
WORKING WIDTH: 2400mm
YEAR: 1997
DOUBLE FOULARD
GAS-HEATED
NUMBER OF ROOMS: 5

MACHINE IS IN VERY GOOD CONDITION

QUANTITY: 1

Learn More

REFERENCE NUMBER: A-1291 (01013JGHB12UM) A SANTEX SANTA SOFT 200 SOFTENING MACHINE – YEAR 2000 – WIDTH 2000 MM YEAR: 2000 ROLLER WIDTH 2000mm GAS AND STEAM HEAT PLAVA MOISTURE CONTROLS ENTRY SCRAY WITH GUIDERS TWO ROLL PADDER TWO SECTION CONTINUOUS TUMBLER EL SPREADING AND CENTERING DEVISE PLAITER QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-8462 SANTEX SANTASHRINK 180 YEAR 1997 WIDTH 1800mm SIEVE DRUM DRYER WORKING WIDTH: 1800mM YEAR: 1997 THE DRYING LINE IS CONSISTING OF: -INFEED -DRYING CHAMBERS -VIBRATION AND STEAMING UNIT -EXIT -DRIVE SYSTEM -EXHAUST AIR SYSTEM -MEASURING UNIT TO MEASURE MOISTURE -CONTRO PANEL THE MACHINE IS PREVIOUSLY USED FOR DRYING POLYAMID TUBULAR MATERIAL WITH CONTROL UNIT SANTAMATIC 2000 3x400V+N+E 230V 50HZ CONNECTED LOAD 64 KW QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More