Search results for: 'control pro''

P-8876 HANDICAP LIFTS FOR STAIRS LOAD: 250KG DRIVE STRUCTURE: RACK MATERIAL: ALUMINUM ALLOY MOTOR POWER: 1KW DRIVE VOLTAGE: 220V 50Hz/ SINGLE PHASE CONTROL VOLTAGE: DC 24V QUANTITY: 1 Learn More

P-8864 COMMERCIAL VERTICAL PLATFORM LIFT PLATFORM SIZE: STANDARD SIZE 1200X900mm LOAD CAPACITY: 300KG LIFTING HEIGHT: 2000mm DIMENSION SIZE: 1200X1000X2800mm QUANTITY: 1 Learn More

REFERENCE NUMBER: Y-2076 TEMPERATURE AND HUMIDITY TEST CHAMBER THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS. IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE. ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS. SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES. THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME. THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER. DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED. VOLUME DIMENSION: ABOUT 150L INTERIOR SIZE: W: 600mm H: 600mm D: 460mm THE MAIN TECHNICAL PARAMETERS TEST CONDITION COOL METHOD: AIR COOLED MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS. THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃ TEMPERATURE FLUCTUATION ± 0.5 ℃ TEMPERATURE UNIFORMITY: ≤ 2.0 ℃ TEMPERATURE DEVIATION: ≤ ± 2.0 ℃ TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃ FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD) COOLING RATE: +20 ℃ TO 40 ℃ FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD) QUANTITY: 1 Learn More

REFERENCE NUMBER: T-6545

MASK BACTERIAL FILTRATION EFFICIENCY (BFE) DETECTOR TESTER

 

PRODUCT INTRODUCTION:

MASK BACTERIA FILTRATION EFFICIENCY KEY PERFORMANCE INDICATORS (BFE) DETECTOR TESTER NOT ONLY CONFORMS TO THE REQUIREMENTS OF MEDICAL SURGICAL MASKS TECHNOLOGY YY0469-2011 APPENDIX B IN THE TEST METHOD FOR FILTER EFFICIENCY (BFE) BACTERIA FIRST B. 1.1.1 TEST INSTRUMENT, BUT ALSO CONFORMS TO THE AMERICAN SOCIETY FOR TESTING MATERIAL ASTMF2100, ASTMF2101, THE REQUIREMENTS OF THE EUROPEAN EN14683 STANDARDS, INNOVATIVE IMPROVEMENTS WERE MADE ON THE BASIS OF THIS, WITH DOUBLE PNEUMATIC CONTRAST SAMPLING METHOD AT THE SAME TIME, IMPROVE THE PRECISION OF SAMPLING,IT IS SUITABLE FOR MEASURING AND TESTING DEPARTMENTS, SCIENTIFIC RESEARCH INSTITUTES, MASK MANUFACTURERS AND OTHER RELEVANT DEPARTMENTS TO TEST THE PERFORMANCE OF MASK BACTERIAL FILTRATION EFFICIENCY.

 

EXECUTION STANDARD:

Q/0212 ZRB003-2015 MEDICAL SURGICAL MASK

BACTERIAL FILTRATION EFFICIENCY (BFE) DETECTOR RELATED INTELLECTUAL PROPERTY:

NO.: ZL200820224142.6 ELECTRIC FLOW CONTROL VALVE

NO.: ZL200820224143.0 GAS CAPACITY

NO.: ZL200920308391.8 AIR FILTRATIONMATERIAL FILTRATION EFFICIENCY DETECTOR

 

PRODUCT FEATURES:

NEGATIVE PRESSURE TEST SYSTEM TO ENSURE THE SAFETY OF OPERATORS;

BUILT -IN PERISTALTIC PUMP IN NEGATIVE PRESSURE CABINET, A, B TWO -WAY, SIX ANDERSEN; THE PERISTALTIC PUMP FLOW CAN BE SET;

THE FLOW RATE OF NIGHT SPRAY CAN BE SET AND THE ATOMIZATION EFFECT IS GOOD.

EMBEDDED HIGH SPEED INDUSTRIAL MICROCOMPUTER CONTROL; 10.4 INCHES INDUSTRIAL HIGH BRIGHTNESS COLOR TOUCH SCREEN;

USB INTERFACE, SUPPORT U DISK DATA STORAGE;

CABINET BUILT-IN HIGH BRIGHTNESS LIGHTS; BUILT-IN LEAKAGE PROTECTION SWITCH TO PROTECT THE SAFETY OF OPERATORS;

THE INNER LAYER OF THE CABINET IS MADE OF STAINLESS STEEL, THE OUTER LAYER IS SPRAYED WITH PLASTIC AND COLD-ROLLED, AND THE INNER AND OUTER LAYERS ARE INSULATED AND FLAME RETARDANT.

THE FRONT SWITCH TYPE GLASS DOOR IS CONVENIENT FOR THE EXPERIMENTER TO OBSERVE AND OPERATE.

DETACHABLE BRACKET, ADJUSTABLE BRACKET HEIGHT; SUPPORTING AND MOVING DUAL PURPOSE CASTERS.

 

QUANTITY: 1

Learn More

How does it work?
What's the system function?
Can it be used as an attendance control unit?

Learn More

REFERENCE NUMBER: J-2273
MAYER CIRCULAR SLIVER KNITTING MACHINES, 24” x 14 GAUGE

ITEM 001 
MAYER CIRCULAR SLIVER KNITTING MACHINES
MODEL HP18SMMII
YEAR: 1997 TO 1998
EACH 24” x 14 GAUGE, 18 HEADS, 72-END CREEL, 1056 NEEDLES
WITH UNIWAVE OIL MISTER, TENSION HEADS, BOTTOM FABRIC DISCHARGE SECTION, MAYER COMPUTER PROCESS CONTROLS, COMPUTER CONTROLLED PATTERN GENERATOR

QUANTITY: 10

ITEM 002
MAYER CIRCULAR SLIVER KNITTING MACHINES
MODEL SK18J
EACH 24” x 14 GAUGE, 18 HEADS, 72-END CREEL, 1036 NEEDLES
WITH UNIWAVE OIL MISTER, TENSION HEADS, BOTTOM FABRIC DISCHARGE SECTION, MAYER COMPUTER PROCESS CONTROLS, COMPUTER CONTROLLED PATTERN GENERATOR

QUANTITY: 10

Learn More

REFERENCE NUMBER: R-9600

PROBAT GG120 BATCH ROASTER

 

BATCH ROASTER

MAKE: PROBAT

MODEL: GG120

OUTPUT CAPACITY: 500 KG PER HOUR

 

MACHINE IN FULLY REBUILT CONDITION, WARRANTY 6 MONTHS

 

QUANTITY: 1

Learn More

R-6859 RE-ROAST 5-10

ROASTING MACHINES LINE, PARTICULARLY SUITABLE FOR LITTLE PRODUCTION ACTIVITIES OF HIGH QUALITY ROASTED COFFEE, SUCH AS SHOPS, PASTRIES OR ARTISANAL LABORATORIES.
SMALL SIZE, TECHNOLOGICALLY ADVANCED, CONFIRM THEMELVES AS IDEAL TOOL FOR THE PRODUCTION OF SELECTED COFFEES.

MADE WITH THE SAME REQUIREMENTS FOR RELIABILITY AND SECURITY FEATURES OF THE BIGGER AND MORE SOPHISTICATED INDUSTRIAL ROASTING MACHINES, ARE AVAILABLE WITH HEATING GENERATOR TYPE GAS BURNER (AVAILABLE ALSO BY ELECTRIC RESISTANCES) AND AUTOMATIC CONTROL SYSTEM WITH SEMIAUTOMATIC MANAGEMENT.

TECHNICAL DATA:
PATENTED ROASTING SYSTEM FOR HIGHER THERMAL EFFICIENCY ALLOWING
THE BEST POSSIBLE RESULT IN ROASTING COFFEE BY HOT AIR-CONVECTION.

HOPPER OF CHARGE STEEL MADE
HEATING GENERATOR BY GAS BURNER (AVAILABLE ALSO BY ELECTRIC
RESISTANCES)

COOLING TANK STAINLESS-STEEL MADE AND SELFCLEANING
INDEPENDENT MOTORISATIONS FOR ROASTING DRUM AND COOLING TANK
INDEPENDENT ELECTROVENTILATORS FOR ROASTING DRUM AND
COOLING TANK.

CICLONE-CHAFF COLLECTOR FOR CHAFFS SEPARATION
MACHINE COLOURS AVAILABLES ACCORDING CLIENT’S REQUEST.
NEW: AUTOMATIC UNLOADING SYSTEM AT THE END OF ROASTING CYCLE
NEW: ELECTRIC CONTROL BOARD WITH PLC + TOUCH-SCREEN WITH RECORDING OF ROASTING PARAMETERS.

Learn More

S-1197 LAUNDRY SOAP PRODUCTION LINE, CAPACITY 1000 TO 1500 KG/HR

LAUNDRY SOAP PRODUCTION LINE
CAPACITY: 1000 TO 1500 KG/HR
I. PROJECT INSTRUCTION
THIS PRODUCT LINE IS A SOAP COMPLETE LINE STARTING FROM OIL MELTING, SAPONIFYING, VACUUM DRYING AND COOLING, MILLING SOAP NOODLES, VACUUM EXTRUDING AND THEN CUTTING INTO SOAPS.
THIS PRODUCT LINE HAS ADVANCED TECHNOLOGY INCLUDING COVERING LESS FLOOR AREA, CONSUMING LESS ENERGY, SAVING HUMAN RESOURCES, AUTOMATING PROCESSES, PRODUCING HIGH QUALITY SOAPS WITH 50 TO 80% FATTY ACID CONTENT.
PLEASE NOTICE THAT:
IT IS A TURN-KEY PROJECT. THE PROFESSIONAL TEAM PROVIDE YOU ALL MACHINES AND ACCESSORIES, THE WHOLE PROCESS OF PRODUCTION, FORMULA, LAYOUT DESIGN, MACHINES INSTALLATION, PRODUCTS TRIAL ETC. ALL SOLUTION ACCORDING TO YOUR REQUIREMENTS.
THE QUOTATION INCLUDES ALL EXCEPT: BOILER, WORKSHOP BUILDING, HEAT INSULATING MATERIAL, WIRES, PACKING MACHINE, AND CONSUMABLE MATERIALS FOR INSTALLING (WELDING ROD, CRANE, ELECTRIC WELDER, ETC.).

1. PRODUCTION REQUIREMENTS:
A. STEAM BOILER: 2 MT/HR.
B. WORKSHOP AREA: LARGER THAN 300 M². (L: 35M, W: 7M, H: 7M)
C. POWER: 130 KW, 380 V, 50 HZ.
D. WATER: CIRCULATING WATER FOR VACUUM DRYING SYSTEM: 40 M3; PRODUCTION WATER.
E. CAPACITY: 1000 TO 1500 KG/HR, 8 TO 12 TON/DAY (8 HR/DAY). OIL CONSUMTION: 5 TO 8 TON/DAY.
F. WORKER: 10 TO 12 WORKERS.
2. MATERIAL AND CONSUMING FOR PRODUCING SOAP:
OIL OR FAT OF PLANT OR ANIMAL (PALM OIL, COCONUT OIL, TALLOW OIL, ETC.), CAUSTIC SODA (NAOH), SODIUM-CHLORIDE (NACL), SODIUM SILICATE, FRAGRANCE, PIGMENT, ETC.
3. PRODUCTION PROCESS:
MIX AND MELT OIL --> SAPONIFICATION --> ADD OTHER INGREDIENTS --> VACUUM DRYING --> SOAP NOODLE --> GRINDING --> VACUUM EXTRUDING --> CUTTING.

III. SPECIFICATIONS AND QUOTATION OF EQUIPMENT
1. CARBURETION WORKSHOP:
MIX KINDS OF OIL TOGETHER ON THE BASIS OF THE FORMULA. DEPOSIT AND TAKE OUT THE UNSAPONIFIABLES.

ITEM 001
CARBURETION POOL
MIX KINDS OF OIL TOGETHER ON THE BASIS OF THE FORMULA.
VOLUME: 10 M3.
FIELD WORK
QUANTITY: 1

ITEM 002
STORAGE TANK FOR REFINE OIL
SIZE: Φ2000X2600, 8.2 M3;
FEATURE: WITH COILER INSIDE.
QUANTITY: 1

ITEM 003
WATER PUMP, OIL PUMP, CAUSTIC SODA PUMP
POWER: 1.5 KW/SET.
QUANTITY: 4

ITEM 004
SEAMLESS TUBE
(Φ76X3.5) (Φ57X3.5), ETC.
QUANTITY: SEVERAL

ITEM 005
VALVE
Φ65, Φ40, ETC.
QUANTITY: SEVERAL

ITEM 006
FLANGE, SCREW, ELBOW, GASKET.
QUANTITY: SEVERAL

2. OIL AND FAT SAPONIFICATION WORKSHOP:
OIL AND ALKALI DO REACTIONS IN THE SAPONIFICATION CAULDRONS. IT IS A GOOD COMBINATION OF FOUR SAPONIFICATION CAULDRONS, WATER CIRCULATES FROM NO. 1 CAULDRON TO NO. 4, IT SAVES WATER, NAOH AND NACL AT THE MOST.

ITEM 007
SAPONIFICATION CAULDRON
SAPONIFICATION BETWEEN OIL AND NAOH, LASTING ABOUT 40 TO 60 HRS. SUFFICIENT REACTION. SAVE WATER.
SIZE: Φ2800 X 3000, 20 M3
AUXILIARY FACILITIES: LIQUID CAUSTIC SODA POOL.2 M3
FIELD WORK
QUANTITY: 4

ITEM 008
HIGH TEMPERATURE AND HIGH PRESSURE SOAP PUMP
POWER: 5.5 KW/SET
QUANTITY: 3

ITEM 009
SEAMLESS TUBE
(Φ76X3.5)(Φ57X3.5), ETC.
QUANTITY: SEVERAL

ITEM 010
VALVE
Φ76, Φ48, ETC.
QUANTITY: SEVERAL

ITEM 011
FLANGE, SCREW, ELBOW, GASKET.
QUANTITY: 1

3. SOAP VACUUM DRYING SYSTEM:
TO MAKE SOAP MATERIALS FLASH DRY AND COOL INSTANTLY. TO CONTROL THE FATTY ACID CONTENT FROM 50% TO 80%. TO IMPROVE THE QUALITY OF SOAP MATERIALS.

ITEM 012
INGREDIENTS MIXTURE TANK
PUT ESSENCE, PIGMENT IN THE LIQUID SOAP. HEATING AND MIXING
SIZE: 1.8 M3, Φ1200X1500
FEATURE: WITH PIPE LINER, HEATING AND MIXING
POWER: 4 KW/SET.
QUANTITY: 2

ITEM 013
HEAT EXCHANGER
HEAT THE LIQUID SOAP RAPIDLY
SIZE: Φ325 X 4000
QUANTITY: 1

ITEM 014
VACUUM SPRAY DRYER
THE VACUUM DRYER MAKES THE SOAP FLAKES THINNER AND EVENER, AND COOLS THEM DOWN MORE QUICKLY, TO IMPROVE THE QUALITY OF SOAP NOODLES.
ADOPT HARD TOOTH SURFACE GEAR REDUCER AND THE OIL PUMP INSIDE LUBRICATES AUTOMATICALLY AND MAKES A LONG LIFESPAN. THE THICKNESS OF BARREL IS 14 MM, THE INNER WALL IS PROCESSED BY VERTICAL LATHE TO ACHIEVE THE COAXIALITY AND SMOOTH SURFACE. THE SHAFT IS MADE BY A Φ108 X 14mm SEAMLESS TUBE. THE NOZZLE (Φ10mm) IN THE SHAFT SPRAYS SOAP MATERIALS, AND THE THREE BLADES SCRAPE THEM DOWN, AND THE SOAP MATERIALS DRY OUT FAST AND UNIFORM. THE WHOLE SET OF VACUUM SYSTEM CAN MAKE SOAPS WITH FATTY ACID CONTENT FROM 55% TO 80%.
1. TYPE: XSD-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. BARREL DIAMETER: Φ 1200mm
4. MOUTH DIAMETER: 10mm
5. SPEED: 13 R/MIN
6. POWER: 3 KW
7. DIMENSION: Φ 1600 X 4500mm
8. WEIGHT: 3200 KGS
QUANTITY: 1

ITEM 015
FINE SEPARATORS
SEPARATE THE SOAP POWDER FROM THE WATER WHEN VACUUM DRYING
QUANTITY: 2

ITEM 016
BAROMETRIC CONDENSER
CONDENSE WATER FROM THE SOAP
QUANTITY: 1

ITEM 017
ELIMINATOR
DRAW OFF WATER
QUANTITY: 1

ITEM 018
PELLETIZER
IT IS USED TO PRESS THE VACUUM-DRIED SOAP MATERIALS INTO SOAP NOODLES. LONG DOUBLE SCREWS TURN INWARD TO DRIVE SOAP MATERIALS TO EXTRUDE SOAP NOODLES THROUGH PORE PLATES.
1. TYPE: XSN-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. SCREW DIAMETER: Φ 230mm X 2
4. POWER: 15 KW
5. DIMENSION: 3100 X 1200 X 1550mm
6. WEIGHT: 3000 KGS
QUANTITY: 1

ITEM 019
STAGE VACUUM PUMP
KEEP THE VACUUM SYSTEM IN VACUUM STATE
POWER: 15 KW
QUANTITY: 1

ITEM 020
BUFFER TANK OF VACUUM PUMP
PROTECT THE VACUUM PUMP FROM STEAM WATER
SIZE: Φ600 X1200
QUANTITY: 1

ITEM 021
SOAP PUMP, WATER PUMP
SOAP PUMP: SPECIAL CONSTRUCTURE, DRAW LIQUID SOAP FROM INGREDIENTS MIXURE TANK TO HEAT EXCHANGER. POWER: 7.5 KW
WATER PUMP: FOR WATER CIRCULATING. POWER: 5.5 KW
QUANTITY: 2

ITEM 022
SEAMLESS TUBE AND VALVE
Φ76 Φ48, ECT.
QUANTITY: SEVERAL

ITEM 023
FLANGE, SCREW, ELBOW, ETC.
QUANTITY: SEVERAL

4. FINISHING LINE:
MILL SOAP NOODLES TWICE, VACUUM EXTRUDING SOAP BAR, CUT SOAP CAKES, AT THE SAME TIME STAMP LOGO ON SOAP CAKES.

ITEM 024
THREE-ROLL GRINDING MILL
THREE-ROLL GRINDING MILL IS USED TO GRIND, PRESS THE MATERIAL TO INCREASE ITS DENSITY AND QUALITY.
1. ROLL DIAMETER: Φ260
2. ROLL LENGTH: 780mm
3. MOTOR POWER: 7.5KW
4. ROLL SPEED RATIO: 1:3:9
5. DIMENSION: 1500 X 1200 X 1000mm
6. WEIGHT: 2400 KGS
QUANTITY: 2

ITEM 025
VACUUM PLODDER
VACUUM PLODDER IS USED TO GRIND, REFINE AND PRESS SOAP MATERIAL INTO SOAP BAR. THE ABOVE AND BELOW SCREWS AND TWO ORIFICE PLATES PRESS AND REFINE THE SOAP MATERIAL AND MAKE THE SOAP BAR TIGHT AND THE SURFACE BRIGHT.
THE MOTOR AND THE REDUCER ARE SEPARATED, FOR LONG LIFE-SPAN AND MAINTENANCE. THE BELOW SCREW’ SPEED IS ADJUSTABLE TO REGULATE THE PRODUCTION CAPACITY. THE VACUUM CHAMBER HAS A VISION GLASS TO WATCH THE INNER, THE VACUUM METER TESTS THE VACUUM DEGREE. THE HEATER INSIDE THE OUTLET ADOPT AUTOMATIC TEMPERATURE CONTROL SYSTEM. THE JACKETS OF THE ABOVE AND BELOW BARRELS ARE CONNECTED TO A CIRCULATING WATER SOURCE.
1. TYPE: XS-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. DIAMETER OF SCREW: Φ230mm
4. SPEED: TOP 15; BOTTOM: 12 TO 18
5. POWER: TOP: 11 KW; BOTTOM: 15 KW
6. DIMENSION: 4350 × 1200 × 2630mm
7. WEIGHT: 4500 KGS
QUANTITY: 1

ITEM 026
ELECTRONIC
CUTTING MACHINE
SOAP ELECTRONIC CUTTING MACHINE IS USED TO CUT SOAPS INTO CAKES AND STAMP PATTERNS ON THE SOAP. ADOPT DELTA SERVO MOTOR AND CONVERTER, VOLTAGE STABILIZER AND PRECISION PURIFIED AC VOLTAGE STABILIZER, TO PROTECT MOTOR AND ELECTRICAL COMPONENTS AND TO KEEP HIGH ACCURACY.
THE MOULD WHEELS RUN BY THE MOVING OF SOAP BAR FROM VACUUM PLODDER. BECAUSE OF THE ELECTRONIC TRACKING SYSTEM, IT CAN CUT SOAP BARS WITH ANY SIZES AND WEIGHT AFTER SETTING THE COMPUTER.
THE CHARACTERS AND THE SHAPE OF SOAP IS CLEAR AND NEAT
THE SIZE AND PATTERN ARE DESIGNED ACCORDING TO CUSTOMERS’ REQUIREMENTS
1. SIZE AND WEIGHT: ADJUSTED BY CUSTOMER’S REQUIREMENTS
2. POWER: 2 KW, 380 V, 50 HZ
3. CAPACITY: IN STEP OF VACUUM PLODDER
4. MOULD: WITH ONE SET
5. DIMENSION: 1000 × 400 × 1200mm
6. WEIGHT: 100 KGS
WOODEN CASE
QUANTITY: 1

ITEM 027
CONVEYORS
APPEARANCE IS GOOD AND OPERATION IS STABLE, NON-NOISE AND ANTI-DUST
MOTOR: 1.1 TO 1.5 KW/PCS
QUANTITY: 4

ITEM 028
VACUUM PUMP
FOR VACUUM PLODDER
POWER: 2.35 KW
QUANTITY: 1

5. OTHERS

ITEM 029
EQUIPMENT SUPPORT, OPERATING PLATFORM, LADDER, ETC.
USED IN CARBURATION POOL, SAPONIFICATION CAULDRONS, AND VACUUM SYSTEM
QUANTITY: 1

ITEM 030
DISTRIBUTION BOX
CONTROL MACHINES, BIG BRAND ELECTRICAL COMPONENTS
WOODEN CASE
QUANTITY: 4

6. ADDITIONAL MACHINES AND SPARE PARTS

ITEM 031
ELECTRICAL CABLES
ALL WIRES FROM EACH MACHINE TO THE FOUR DISTRIBUTION BOXES. THE MAIN WIRE FROM THE FOUR DISTRIBUTION BOXES TO THE MAIN DISTRIBUTION BOX AND SLEEVES ARE NOT INCLUDED
QUANTITY: 1

ITEM 032
HEAT INSULATING MATERIAL
ABOUT 450 M3, INCLUDING GALVANIZED SHEET 450 M3. GLASS WOOL CLOTH, NAILS
QUANTITY: 1

ITEM 033
WELDING ROD
ABOUT 50 BOXES, 1 TON.
QUANTITY: 1

ITEM 034
STEAM BOILER
MATERIAL: DIESEL OIL.
RATED POWER: 2000 KG/H
RATED PRESSURE: 1.25 MPA
RATED STEAM TEMPERATURE: 194 ℃
THE QUOTATION IS FOR ONE WHOLE SET OF BOILER, INCLUDING THE STEAM BOILER, WATER TREATMENT EQUIPMENTS, WATER BOXES, OIL BOXES, PUMPS, AND SOME SPARE PARTS
THE QUOTATION INCLUDES SALARY OF BOILER ENGINEER'S INSTALLATING AND TESTING
THE AIR TICKET AND ACCOMMODATION ARE NOT INCLUDED
LOADED BY A 40 'GP CONTAINER
QUANTITY: 1

QUANTITY: 1 PLANT

Learn More

REFERENCE NUMBER: M-0017 AUTOMATIC VACUUM FOAMING BATCH MACHINE AUTOMATIC VACUUM FOAMING BATCH MACHINE, USES BATCHING TECHNOLOGY, FOAMING IN VACUUM CONDITION. IT IS COMPOSED OF STORAGE TANKS, BATCHING, MIXING, VACUUM, MOULD, AND COMPUTERIZED CONTROLLING SYSTEMS. USES NUMERICAL CONTROL DURING THE WHOLE PRODUCTION. IT IS USED FOR MAKING ALL KINDS OF FOAM. ADVANTAGE: *USING THE SAME PPH OF WATER, FOAMING DENSITY WILL BE LOWER: ≤30% * REDUCES THE CHEMICAL CONSUMPTION, AND SAVES ON THE FOAMING COST: ≤20% * SUCTION AND FILTRATE THE FOAMING AIR. * MONITOR THE WHOLE FOAMING BY WIRED TELEVISION. * WITH NUMERICAL CONTROL WITH ACCURATE AND CONVENIENT MEASURING DURING THE WHOLE PRODUCTION. EASY AND STABLE TO OPERATE THE MACHINE. OUTPUT 1 BLOCK / 12MIN CHEMICALS 8 GROUPS MIXER 220 KGS MOULD SIZE 2200（L）X 1800（W）X 1300 (H) mm 2200（L）X 1500（W）X 1300 (H) mm LIFTING PLATFORM SPEED ≤3M/MIN ( AUTOMATIC REGULATION ) MAX SUCTION 0.05MPA POWER 42KW QUANTITY AVAILABLE: 1 Learn More