Search results for: 'PRODUCT+MO'

R-7837 UNIDIVIDER BUNS LINE, CAPACITY 4,000 TO 11,000 PIECES PER HOUR, IN NEW CONDITION

HEADMACHINE 4/5/6 ROW

LONG MOULDER WITH DRIVEN UPPER BELT WORKS IN 2 DIRECTIONS

LONG MOULDER ADJUSTABLE IN HIGHT

SYNCHRONISATION TO GET ALL THE PRODUCTS IN LINE BEFORE DEPOSITING

REFERENCE NUMBER: L-1656
LOST FOAM CASTING PROCESS FOUNDRY MACHINERY
QUANTITY: 1

P-3516 BALEMASTER AUTO-TIE BALER WITH PAPER SHREDDER AND LOADING CONVEYOR YEAR 1989

BALEMASTER
AUTO-TIE BALER WITH PAPER SHREDDER AND LOADING CONVEYOR
YEAR: 1989
6’ WIDE x 32’ LONG INCLINED LOADING BELT CONVEYOR:
ORIGINAL INSTALLATION:
THE ENTRANCE WAS BELOW FLOOR LEVEL ALLOWING FLOOR LEVEL, PUSH-TYPE LOADING. PRODUCT THEN FALLS ONTO A SHORT SECTION OF SHREDDER FEEDING CONVEYOR
EQUIPPED WITH:
24 INCHES HIGH SIDE GUIDES
AUTO BELT TRACKING

BALEMASTER
SERIES 1350J-62 PAPER SHREDDER
62 INCHES WIDE
SPECIFICATIONS:
MOUNTED TO TOP OF BALER FEED CHUTE
WAS USED FOR MAGAZINE EDGE TRIM & NEWSPAPER, BUT CAN BE USED FOR OTHER MATERIALS

BALEMASTER
MODEL: 4025C-8
AUTO TIE BALER
YEAR: 1989
SPECIFICATIONS:
MATERIALS: NEWSPRINT, MAGAZINES, CORRUGATED CHIPBOARD, FIBERBOARD, BOXBOARD
BALESIZE: 28 INCHES W x 36-1/2 INCHES H x UP TO 84 INCHES LONG
BALE WEIGHT: 1,440 POUNDS @ 72 INCHES LONG
OPENING SIZE: 17 INCHES x 32 INCHES
BALER HEIGHT: 48 INCHES
BALER HEIGHT WITH CHUTE: 72 INCHES
CYLINDER DIAMETER: 8 INCHES
THRUST: 150,900 POUNDS @ 3,000 PSI
NUMBER OF WIRE REELS: 5 @ 100 POUNDS EACH
(10) AUTO TWISTER HOOKS, (5) CUTTERS PER SIDE

EQUIPPED WITH:
AIR COOLED HYDRAULIC OIL COOLER FOR CONTINUOUS OPERATION WITH ITS OWN MOTOR & PUMP WATER SPRAY SYSTEM
(2) 5’ LONG BALE TAKE-AWAY TABLES

MOTOR DATA: 25 HP BALER, 230/460/60/3

NOTE: INSTALLATION ASSISTANCE AVAILABLE

QUANTITY: 1

M-6262 RF SYSTEMS TD-85 RADIO FREQUENCY DRYER FOR CONES YEAR 2002

RADIO FREQUENCY DRYER FOR CONES
MAKE: RF SYSTEMS
MODEL: TD-85 (K85)
YEAR: 2002
THREE PHASES 380 – 50 HZ
FOR DIFFERENT VOLTAGE THE MACHINE IS EQUIPPED WITH AUTO TRANSFORMER
THE NOMINAL VOLTAGE SHOULD BE WITHIN 5% (TEMPORARY EXCURSIONS OF +5% AND -5% ARE PERMITTED) OTHERWISE CUSTOMER MUST INSTALL A SUITABLE STABILIZER
MAXIMUM POWER ABSORBED FROM THE MAINS: 130 KVA
MAXIMUM CURRENT ABSORBED: 210 A
GAUGE WIRE: 3x75mm2 + GROUND 50mm2 MINIMUM

GENERATOR
MAXIMUM POWER RADIO FREQUENCY GENERATOR: 85 KW (1 x 85KW)
WORK FREQUENCY: 27 MHZ
COOLING SYSTEM: FORCED AIR
MAXIMUM ROOM TEMPERATURE: TA = 35°C IF HIGHER POWER MUST BE REDUCED
MAXIMUM EXHAUST AIR TEMPERATURE: TU = 85°C
OSCILLATOR: CAVITY TYPE WITH HIGH OVERALL EFFICIENCY
FREQUENCY STABILITY: WITHIN LIMITS
RADIATED FIELD: WITHIN LIMITS
GRID CURRENT WITH NO LOAD: 2.3 A TO 2.5 A
GRID CURRENT MINIMUM WITH FULL LOAD: 1.4 A
TRIODE TYPE: RS 3060 CL
FILAMENT TRIODE VOLTAGE: 10 V + 1% - 3%

BELT – CONVEYOR
MATERIAL: POLYESTER FABRIC
TRACKING: AUTOMATIC
LENGTH: 21600mm
WIDTH: 1750mm
RANGE OF CONVEYOR SPEED: 0 TO 50 M/ORA
ELECTRODE: STANDARD TYPE

PRODUCTIVITY
MAXIMUM EVAPORATING CAPACITY: 90 KG WATER PER HOUR

DIMENSIONS
LENGTH: 9600mm
WIDTH: 2124mm
MAXIMUM HEIGHT: 3400mm
GALLERY LENGTH: 4000mm
INLET LENGTH: 2800mm
OUTLET LENGTH: 2800mm
BELT WIDTH: 1750mm
LOAD HEIGHT: 900mm
MAXIMUM HEIGHT OF INLET TRAP: 300mm

THE DRYER TD85 IS COMPOSED OF ONE UNITY OF 85 KW

SPECIAL REQUIREMENTS ON USING RADIO FREQUENCY DRYER
THE DRYER CAN ACCEPT ONLY HYDROEXTRACT GOODS WITH EVEN MOISTURE CONTENT
POSSIBLE FIRE HAZARD WHEN DEALING WITH UNEXTRACTED PACKAGES
PROPEN HYDROEXTRACTION IS IMPORTANT PRIOR TO RF DRYER
LOAD PRODUCT WITH SAME DIMENSIONS AND SIMILAR MOISTURE CONTENTS
PACKAGE PLACEMENT ON THE BELT. ANY TYPE OF TUBE MAY BE USED IN A CONTINUED RF DRYER
METAL TUBES REQUIRE MOVE CARE IN PLACEMENT ON THE BELT THEN PLASTIC TUBE
METAL TUBES CAN CAUSE SHORT CIRCUITY, OR ARCING, FROM ONE ELECTRODE TO GROUND, WHICH CAN DAMAGE THE BELT OR CAUSE FIRE
PACKAGE WITH METAL TUBES MUST BE PLACED ON THE BELT SO THE METAL IS PARALLEL TO THE ELECTRODES AS SHONS IS TY
THE CONVEYOR SHOULD ALWAYS BE LOADED EVENLY, WITH NO BIG EMPTY GAPS
LOAD AS MUCH AS YOU CAN
GOOD WITH DIFFERENTS SIZE ARE NOT ALLOWED THEY CAN GET BURNS
LOAD A QUANTITY OF GOODS WITH A QUANTITY OF WATER TO REMOVE PER LINEAR METER OF BELT AROUND 5 TO 15 KG PER LINEAR METER OF BELT
THE MACHINE CANNOT ACCEPT METALLIC DYSTUFF (EX.CHROME)
DO NOT ENTER METALLIC PARTS
METALLIC IN THE GALLERY CAUSES ELECTRICAL DISCHARGES WHICH MAY THOROUGHLY RUIN BELT AND SET THE DRYING MATERIAL ON FIRE

QUANTITY: 1

REFERENCE NUMBER: P-4337

WET TOWEL MAKING MACHINE.(HALF FOLD TYPE)

Model: L60
SPECIFICATIONS:
Model: Z, V, W,Z+Z...
Packing Item: Non-woven fabric
Capacity: 450-640 sheets/min or 20-80bags/min
Raw Material Size: parent roll dia: 1000mm,Core dia:76.2mm
Wet towel Size: Length 100mm. Width: 50-100mm (adjustable)
Open size: Length 200mmx Width(150-250)mm
Products size:Length:130-350mm Width:50-120mm, Thickness:5-45mm
Wetting System: Moistening system complete with 100%-400%, automatic,  excess liquid
Cutting system: stainless steel round cutter
Counter system: electronic meter
Feeding system: by manual
Hole system: synchronization rotary cutter
Label system: synchronization sticker
Power: 3 phase AC 380V  50/60Hz 8KW
Machine space: L:5000mmXW 4300mm XH1900mm (L)
Machine weight: 2000kg
Remarks: Machine made by stainless steel. Special size by order

OPTION EQUIPMENT
Coding machine Stainless steel storage tank

QUANTITY: 1

REFERENCE NUMBER: P-4324

PORTABLE WIPES, MODEL WL68

Model: WL68

Machine Characteristic
Control system: Multi-Axis Motion Controller
Drive element: servo motor
Operate interface: 8" LCD touch screen
Packing style: end seal & reciprocating  type
Frequency division detection: nonwoven, film, label detect respectively
Auto splicing: raw material & film automatic bonding, label automatic switching
Wipes stacking: manipulator
Inferior eliminate: color bonding connector rejected online
Flow control: 2.5-4 times, flow meter control
Moisture type: 4 fluid pipes  spray independently
SUS Agitate tank: 2 sets, 600L stainless steel agitate tank
Liquid level control: electronic detection, auto control

Specifications
Raw material: spunlaced nonwoven, therbond etc.  nonwovens
Raw material specification: max W800mm, φ1000mm
Axis QTY settings:2 rolls raw materials ,1 roll cut into 4 channels,1 roll stand by auto splicing
Diameter of ventilating shaft: 3"
Suitable packing material :BOPP  PET/PE PET/AL/PE etc. heat-seal material
Packing Film specification: max W420mm, φ350mm
Diameter of ventilating shaft: 3"
Suitable label: transparent label & opaque label
Label size: max W100mm  φ400mm
Axis QTY settings: 2 sets label, automatic switching without stopping(can be set as safety label)
Folding  type: Z fold
Wet wipes size:L90-105mm  W55-100mm
Open size: L175-205mm W140-200mm
Package size: L130-200mm W60-110mm H5-50mm
Production speed: 70 bags/min &1200 pieces/min
Machine space: L8100mm W4000mm H2100mm
Power: AC 380V 50/60Hz 20KW
Compressed air: 0.6-0.8Mpa 250L/min
Machine net weight : 7500kg

Option equipment: Coding machine Metal detector

QUANTITY: 1

REFERENCE NUMBER: V-1468

SURGICAL GAUZE COMPRESSING, FOLDING, AND BAGGING MACHINE

COTTON GAUZE MEDICAL COMPRESS FOLDING AND BAGGING MACHINE, WHICH AUTOMATICALLY FOLDS COTTONG GAUZE, COMPRESSES, AND THEN PACKS THEM INDIVIDUALLY OR IN GROUPS INTO SACHETS.

FEATURES             

USEFUL WIDTH: 45 CM

NUMBER OF TRACKS: MAXIMUM 2 (VARIES ACCORDING TO THE SIZE OF COMPRESSES)

SIZE:

MINIMUM DIMENSIONS OF COMPRESSES: 5 CM X 5 CM

MAXIMUM DIMENSIONS OF COMPRESSES: 10 CM X 20 CM (16 PLIES)

ALL THE USUAL OR INTERMEDIATE SIZES CAN BE PRODUCED ON THE MACHINE BY SIMPLE ADJUSTMENTS.

NUMBER OF PLIES 8 / 12 / 16 / 20 / 24 / 28 / 32 PLIES (VARIES ACCORDING TO THE SIZE OF COMPRESSES)

FOLDING: THE CONVENTIONAL FOLDING IS THE 5-FOLD "SURGICAL" OR "AMERICAN" TYPE, WITH EDGES AND CORNERS TUCKED-IN, HOWEVER BY OFFSETTING FOLDS OTHER COMBINATIONS ARE POSSIBLE.

STACKING:  STACKING IS CARRIED OUT IN THE CHANNELS WHERE THE COMPRESSES ARE COUNTED AND READY TO BE MANUALLY INSERTED INTO PAPER BAGS.

PRODUCTION      :

EXAMPLES OF THEORETICAL PRODUCTIONS:

5 CM X5 CM 8 PLIES (2 TRACKS) 13200 COMPRESSES PER HOUR

7.5 CM X 7.5 CM 12 PLIES (2 TRACKS) 13200 COMPRESSES PER HOUR

10 CM X 10 CM 12 PLIES (2 TRACKS) 12000 COMPRESSES PER HOUR

OPTIONS:

BARIUM FIXING TRACK BY TRACK

GAUZE ROLL LOADING BY PNEUMATIC CYLINDERS"

FEATURES LIST:

MATERIAL SUPPORT ADJUSTABLE IN WIDTH,

POSITIVE UNWINDING WITH TENSION CHECK ADJUSTABLE TRACK BY TRACK,

MULTIPLE LENGTH FOLDING DEVICE ADJUSTABLE TRACK BY TRACK,

SPRAY HUMIDIFYING SYSTEM,

SUCTION SYSTEM,

ANTI-STATIC BARS,

ADJUSTABLE FLY CUT MODULE MOTORISED WITH BRUSHLESS MOTOR,

THREE CROSS FOLDING MECHANISMS WITH INDEPENDENT ADJUSTMENT OF EACH FOLD,

TRANSFER BELTS FOR THE COMPRESSES,

MOTORISED LATERAL UNWINDING OF THE PAPER ROLL MODULE,

DEVICE FOR INDIVIDUAL, IN MULTIPLES OR IN SHINGLED FORM PACKAGING - WITH A CHANGEABLE

NUMBER OF COMPRESSES BY SACHET,

CHECK OF FOLLOWING OPERATIONS TRACK BY TRACK:

. END OF FABRIC,

. PRESENCE OF SEAM,

. PRESENCE OF CROSS-FOLDED COMPRESS,

. JAM PREVENTION BEFORE PACKAGING.

COLD SEALING BY PRESSURE AND CUTTING OF SACHETS IN PRINTED AND ZONED PAPER,

POWER SYSTEM OF PACKAGING BY BRUSHLESS MOTOR ALLOWING FOR FLY ADJUSTMENT OF:

. THE COMPRESS POSITION IN THE SACHET,

. THE CROSSWISE KNURLING POSITION,

. THE CROSSWISE CUTTING OF SACHETS.

ACCELERATION RAMP BY FREQUENCY VARIATION,

MACHINE OPERATION BY TOUCH-SENSITIVE SCREEN:

. STORABLE CONFIGURATIONS,

. CLEAR LANGUAGE FAULT DISPLAY,

. COUNTERS : TOTALIZER, PRE-SELECTION, ETC.,

. SOUND AND VISUAL ALARMS,

. "INCIDENT" STATISTICS.

STARTING, STOPPING, STEP BY STEP - BY REMOTE CONTROL.

* CONTINUOUS, TRACK BY TRACK INTEGRATION OF ULTRASONIC BARIUM FIXING.

* PAPER ROLL LOADING BY PNEUMATIC CYLINDERS.

* INK JET MARKING UP TILL 8 LINES.

* SACHETS QUALITY CONTROL DEVICE: EITHER A CHECK BY PHOTO CELLS, OR BY CAMERAS,

* FAULTY SACHET EJECTION DEVICE.

* TABLE WITH CONVERGING BELTS.

REFERENCE NUMBER: M-6075
SULZER P7200 & P7250 TERRY LOOMS, WIDTH 3600mm, YEAR 2000, DOBBY

DETAILS:
TERRY WEAVING LOOMS
MAKE: SULZER
(2) X MODEL P7250
(4) X MODEL P7200
YEAR: 2000
WIDTH: 3600mm
DOBBY 20/20 (10 INSTALLED) 
EACH LOOM HAS 4 FEEDERS
3500 DROPPERS 
7,000 YARNS FRAME FOR NORMAL PRODUCTION OF TOWEL LOOMS
EACH 2 LOOMS HAVE A TOOL BOX
SPARE GRIPPER AND RIBBON EACH 2 LOOMS
2 BEAMS ON LOOM AND 3 SPARES
3 SETS OF SPARE GRIPPER AND RIBBON FOR THE 6 LOOMS 
OFF LOOM TAKE UP

QUANTITY: 6

C-3994 BARGEMOUNTED POWER PLANT, CAPACITY 220MW

A. ONCE THROUGH STEAM GENERATOR
B. BARGE
C. CHILLERS
D. AIR COMPRESSOR
E. GAS TURBINE
F. STEAM TURBINE
G. FEEDWATER SYSTEM
H. CLOSED COOLING WATER SYSTEM
I. AUXILIARY COOLING WATER SYSTEM
J. CONDENSATE POLISHING UNIT (CPU)
K. WASTE WATER SYSTEM
L. PLANT ELECTRICAL SYSTEM
M. BLACK START DG SET
N. PLANT CONTROLS AND INSTRUMENTATION
O. PLANT FIRE FIGHTING SYSTEM
P. START UP VACUUM SYSTEM
Q. STEAM TURBINE DEAERATING CONDENSER

QUANTITY: 1 PLANT

REFERENCE NUMBER: M-6091
FULLY AUTOMATIC PVC MEDICAL URINE BAG MACHINE

MACHINE FOR PRODUCING DISPOSABLE URINE/URINARY COLLECTING BAG, DRAINAGE BAG, ETC.
PLC CONTROL, COMPUTER TOUCH SCREEN CONTROLLING SYSTEM, WITH PRECISE, EASY OPERATION.