Search results for: 'sli'

INTERSECTING COGNETEX MODEL RVC 22V FEEDING CREEL 8 DOUBLINGS FOR CANS AUTOMATIC DELIVERY INTO 2 CANS – 2 SLIVER DIAMETER 700 X 1200 YEAR OF CONSTRUCTION 1985 Learn More

REFERENCE NUMBER: M-4868 (1111275NKG10RX) L PUB BREWERY 20HL SPECIFICATION: 1. MALT HANDLING - CYLINDER-CONIC MALT SILO WITH 25M³ CONTENT, MADE IN FIBRE GLASS / PLASTIC, STANDING OUTDOOR ON STEEL CONSTRUCTION - MALT CONVEYORS / SPIRAL CONVEYOR INTO 1ST FLOOR - 2-ROLLER MALT MILL - GRIST CASE - FALL PIPE IN MASH COPPER (FOR DUST FREE MASHING-IN) - GIBBET-LIFT FOR BAGGED SPECIAL MALTS 2. BREWHOUSE TOWER BREWHOUSE FOR 20 HL / BREW, COMPLETE IN STAINLESS STEEL, BUILT 1994, STEAM HEATED, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, 2 CRANE EYELET, 2 STAINLESS STEEL PLATFORM, WITH: - MASH- / WORT COPPER WITH BOTTOM HEATING ZONE AND INTERIOR COOKER, SIDEWAYS AGITATOR, MANWAY ENTRANCE HATCH, LIGHTNING, STEAM REGULATION VALVE - LAUTER TUN, WITH STAINLESS STEEL RAKING MACHINE WITH SEW-DRIVE FROM TOP, WITH SPENT GRAINS SLIDER, STAINLESS STEEL FALSE BOTTOM, SPENT GRAINS HATCH, VERTICAL SIGHT GLASS, LIGHTNING, SPRAY HEAD, DOME LID WITH BUILT IN CONTROL CABINET - SPINDLE STATION WITH WASHING TABLE IN STAINLESS STEEL, ABOUT 1,5M WALL ASSEMBLED - HOT WATER TANK, WITH 30 HL, IN STAINLESS STEEL, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, HEATABLE, WITH MANWAY IN THE WALL, LEVEL DISPLAY - PRESSURE RAISING PUMP - WORT COOLING, 1-STAGE PLATE APPARATUS - WORT AERATION IN STAINLESS STEEL 3. FERMENTING- AND STORAGE TANKS - 5 CCTS, WITH 40 HL NET / 46 HL GROSS CONTENT, ALL TANKS 3 BAR, BUILT 1994, STANDING ON FEET, PI-ISOLATED FULLY WELDED WITH STAINLESS STEEL JACKET, WITH JACKET COOLING FROM CONE BELOW TO ½ WALL 60 LT COOLING JACKET 3 BAR, WITH MANWAY IN THE WALL, 2 OUTLETS WITH BUTTERFLY VALVES, TEMPERATURE SENSOR PT100, SPRAY HEAD, PULLED DOWN CLEANING PIPE WITH BUTTERFLY VALVE, BUNGING ARMATURE, OVER PRESSURE VALVE, SAMPLER, 2 CRANE EYELETS, 2 OF THE TANKS WITH LEVEL DISPLAY - DIGITAL TEMPERATURE CONTROL FOR 5 TANKS IN STAINLESS STEEL CONTROL CABINET - CIRCULATING PUMP IN STAINLESS STEEL, MOBILE, WITH SWITCH - MANY GOOD BEER HOSES - 6 X 10 HL BEER DISPENSING TANKS, MAKE DUO TANK, BUILT 2002, 3,0 / 4,3 BAR, COOL ABLE, ISOLATED WITH STAINLESS STEEL-JACKET FULLY WELDED, FOR INLINE-OPERATION, LYING IN RACK, SCREWED STAINLESS STEEL RACK, WITH PRESSURE ARMATURE, OUTLET ARMATURE WITH REDUCTION TO BARE CONNECTION, MANWAY WITH BIG SIGHT GLASS IN MANWAY LED - PANEL FOR 3 TYPES OF BEER 4. FILLING COMBINED BOTTLE-/KEGGING PLANT, WITH 1 CLEANING TUB, HEATED AND 1 REBUILT KEG: - BOTTLE CLEANING MACHINE FOR CLEANING OF 8 BOTTLES INSIDE AND OUTSIDE, FOR UP TO 2LT BOTTLES - BOTTLE FILLING STATION WITH HUB CYLINDER FROM BELOW, WITH SPLINTER PROTECTION - COMBINED KEG-CLEANING- AND FILLING STATION - BUILT IN CONTROL CABINET WITH SIEMENS S5 CONTROL AND OPERATING CONSOLE OP 7 5. OTHER EQUIPMENT - STEAM BOILER FOR ABOUT F280 KG/H, WITH GAS BURNER, FULLY SERVICED ON 4TH AUGUST 2014, BUILT IN 1994 - CONDENSATE TUB IN STAINLESS STEEL AT WALL AND SECOND SMALL S/S-TUB - WATER TREATMENT - STEAM REGULATION AND CONDENSATE VALVES IN CYCLE - STAINLESS STEEL CHIMNEY PLANT ABOUT 8-10M - AIR COMPRESSOR WITH WIND KETTLE, BUILT 1994 - COOLING PLANT / COLD WATER PLANT, MAKE L&R KÄLTETECHNIK, TYPE: WRK-17/SL/-5, PLANT BUILT 1997, COOLING AGENT R 407 C, WITH NEW COMPRESSOR AND NEW PLATE HEAT EXCHANGER IN 2014 FOR 10,000 € INVESTED, EVAPORATOR WITH 2 VENTILATOR OUTSIDE HANGING ON THE WALL 6.1 OTHERS - ABOUT 100 KETS, MAKE SCHÄFER, PLUS-KEGS, FLAT FITTING IN DIFFERENT SIZES, NEUTRAL - PARTY-KEGS, WITH BAVARIAN TAP, PU-COVERED IN BLACK AND WITH WOOD-OPTIC - ABOUT 800 NEUTRAL CLIP LOCK BOTTLES EACH 1 LT 6.2 DIMENSIONS THE ROOM HEIGHT IN BREWHOUSE AND CCTS IS 4.50M. THE PLANT AS ASSEMBLED ON 10.75 X 4.38M. PLEASE NOTE THAT THE BREWERY IS ONLY AVAILABLE AS A SINGLE SALE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4787 (1111BGJWXX10) L BLACK CLAWSON EXTRUSION COATER LAMINATOR YEAR 1992 WEB WIDTH 1575mm BLACK CLAWSON EXTRUSION COATER LAMINATOR YEAR 1992 WEB WIDTH 1575mm (62 INCHES) L/D(S): 30:1 DRIVE SYSTEM: 250HP DC DRIVE SPEED: 305 MPM (1000 FPM) EXTRUDER(S): BLACK CLAWSON PRIME COATER: NONE SIZE(S): 4-1/2” PRIMARY UNWIND: NONE SECONDARY UNWIND: NONE REWIND: NONE DRYER TYPE: NONE EQUIPPED WITH MODEL 111 EXTRUSION COATER WITH 30” DIAMETER X 72” FACE CHILL ROLL PRESSURE ROLL ASSEMBLY WITH 12” DIAMETER, 6” DIAMETER NIP ROLL AND LEAD-IN SPREADER ROLL 11” DIAMETER SECONDARY CHILL ROLL; SLITTING STATION MODEL 400 EXTRUDER MOUNTED ON XYZ CARRIAGE WITH 250HP DC MOTOR 4-1/2” DIAMETER SCREW IS ELECTRICALLY HEATED AND WATER COOLED; VALVED ADAPTER 72” CLOEREN AUTOMATIC DYE WITH EDGE BEAD REDUCTION AND EXHAUST HOOD QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4620 (111113DWQ10RXL) J INTERSECTING COGNETEX MOD.SC 22 V YEAR 1994 INCLUDES: - FEEDING CREEL N.10 COUPLINGS BY CANS - DELIVERY N.2 SLIVERS IN N.2 CANS 800 X 1200 - AUTOMATIC DOFFING - YEAR 1994 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

REFERENCE NUMBER: M-4827 (1111LWYCXX10) L FANCY YARN TWISTING MACHINE EXPO-2000 YEAR 2004 FANCY YARN TWISTING MACHINE PA.FA MODEL EXPO 2000 40 HEADS FEEDING BY SLIVER SINGLE DRAFT HOLLOW SPINDLE DELIVERY ON CONE PITCH 8” (200mm) YEAR 2004 COMPLETE WITH COPS MACHINE PA.FA WITH 6 SPINDLES BOBBINA FOR HOLLOW SPINDLE SUPPLIED DELIVERY: PROMPT QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: A-0005 (111125GHT10U) A BIANCO OPENER 2200mm 220 CM MACHINE NO SLITTER NEW COVERING ON ROLLERS NEW BEARING ON GUIDE ROLLER COMES WITH CENTER WIND DC MOTOR AND DRIVE AND GEARBOX FOR HEAVING PULLING IF NEEDED. QUANTITY AVAILABLE: 1 Learn More

01 MALT HANDLING 02 BREWHOUSE 03 WORT COOLING 04 YEAST STORE 05 FERMENTING-AUND MATURATION CELLAR 06 FILTRATION 07 BRIGHT BEER CELLAR 08 SOFTDRINK PREPARATION 08-02 MIXING TANK 09 STEAM SUPPLY 10 AIR SUPPLY: 11 REFRIGERATION SUPPLY 12 BOTTLING LINE FOR NON-RETURNABLE GLASS BOTTLES 13 CANNING LINE FOR 250 ML SLIM-LINE 14 KEG LINE Learn More

REFERENCE NUMBER: M-4796 (11111575DJQ10RX) L COMPLETE BREWERY 65HL INCLUDING FILLING LINES AND KEG LINE DELIVERY OF ONE 65 HL BREWERY WITH THE FOLLOWING EQUIPMENT: 1. MALT HANDLING - MALT ACCEPTANCE BY BIG PACKS - MALT ELEVATOR TO CONDITIONING TANK - GRIST CASE - MALT MILL, MAKE STEINECKER, TYPE: MAISCHOMAT 3003, WET MALT MILL, BUILT 1997 2. BREWHOUSE EQUIPMENT 3-KETTLE-STEINECKER-BREWHOUSE WITH 65 HL CAST WORT, COMPLETE IN STAINLESS STEEL, DRIVES FROM BELOW, AUTOMATED, WITH SIEMENS S5 CONTROL, BUILT 1997 - MASH TUN WITH MASHING FROM BELOW, BOTTOM HEATING ZONE, MASH PUMP, Ø: ~2.500mm - LAUTERTUN, WITH 2-ARM RAKING MACHINE, STAINLESS STEEL KNIFES, 6-PARTED STAINLESS STEEL FALSE BOTTOM, RING LAUTERIG, FALSE BOTTOM RINSING, SPENT GRAINS FALL PIPE, FLOW METER, LAUTER PUMP, Ø: ~2.500mm - WORT KETTLE / WHIRLPOOL, WITH INTERNAL COLANDRIA, WITH TANGENTIAL INLET, SPRAYBALL, WORT PUMP, ~2.500mm - AUTOMATED CONTROL OVER PC FOR BREWHOUSE UNTIL FERMENTING CELLAR AND CIP - ELECTRICAL CONTROL CABINETS - STEEL CONSTRUCTION BETWEEN THE VESSELS - HOT WATER TANK, 200 HL CONTENT, IN STAINLESS STEEL, ISOLATED, HORIZONTAL, STEAM HEATED, WITH MANWAY, MEASUREMENTS: Ø: 2.400 mm x L: 5.700 mm x H: 2.800 mm, WITH PLATE HEAT EXCHANGER, FREQUENCY CONTROLLED PUMP, CONTROL CABINET - COLD WATER TANK, HORIZONTAL, ~150 HL CONTENT, IN STAINLESS STEEL, ISOLATED, WITH MANWAY, MEASUREMENTS: Ø: 2.300mm x L: 4.000mm x H: 2.400mm, WITH PLATE HEAT EXCHANGER, PUMP, CONTROL CABINET - 1 CIP-TUB 3. WORT COOLING - WORT COOLER, MAKE SONDEX, TYPE: S38-FG, 1-STAGE, FOR ICE WATER, 6 BAR, 0,130°C, FLOW METER, BUILT 1998 - WORT AERATION 4. FERMENTING- + STORAGE CELLAR - 9 CYLINDER-CONICAL FERMENTING- AND STORAGE TANKS, INDOOR-CCTS, MAKE HOLVRIEKA, WITH EACH 300 HL GROSS CONTENT, 0,99 BAR, STANDING ON 4 FEET, WITH 3 COOLING ZONES 2 OF THEM IN THE WALL AND 1 CONE COOLING ZONE, WALL ISOLATED WITH PU-FOAM WITHOUT COVERING, CONE ISOLATED AND COVERED, WITH SCANDI BREW ARMATURES, SAMPLER, CLEAR AND REST OUTLET, HEIGHT: ~ 7.500mm, Ø: ~2.900mm, BUILT 1997 - 2-TANK-CIP-PLANT, AUTOMATED, ONLY FOR THE CCTS, IN STAINLESS STEEL, WITH LID, LEVEL DISPLAY, PIPING, PUMP, AUTOMATIC APV VALVES - 2 PANEL, WITH SWIVELLING BOWS - PUMPS - CARLSBERG FLASK FOR YEAST PROPAGATION FROM SCANDI BREW - 1 YEAST TUB, ABOUT 100 LT, IN STAINLESS STEEL, WITH LID, AS TRANSFER TUB - YEAST PUMP, MOBILE 5.1 FILTERCELLAR 100 HL/H - KIESELGUHRFILTER, MAKE SCHENK, TYPE: ZHF-S25, FOR 100 – 125 HL/H WITH OPERATING PLATFORM, HYDRAULIC DRIVE, HYDRAULIC AGGREGATE, STANDING ON BASIS FRAME, BUILT 1989, GRATING, CONTROL CABINET - KIESELGUHR DOSAGE, WITH AGITATOR, LID, DOSAGE PUMPE, PRECOATING PUMP - DOSAGE TUB WITH AGITATOR AND PUMP, MOBILE, WITH PLUG - ROOM AIR EVAPORATOR WITH 2 FAN 5.2 BBT CELLAR - 3 STAINLESS STEEL BRIGHT BEER TANKS / BBTS, MAKE HOLVRIEKA, EACH 140 HL, 1 TANK WITH 1,5 BAR, 2 OF THEM WITH 1,0 BAR BUILT 1997, MOULDED BOTTOM TANKS, NOT COOLABLE, STANDING ON 4 FEET, WITH MANWAY, SPRAY HEAD, PULLED DOWN CLEANING PIPE, SAMPLER, MANOMETER, Ø: 1.500 mm, BUILT 1998 - BEER PUMP - PANEL, MAKE PALL - 1 CIP-TUB, MANUAL, WITHOUT LID, STANDING ON 3 FEET, ~100 LT CONTENT, PUMP - CO2 MEASURING UNIT MAKE HAFFMANS, MOBILE 6. COMBINATED BOTTLING LINE, NON RETURNABLE BOTTLES AND CANNING LINE FILLING LINE FOR NON RETURNABLE GLASS BOTTLES FOR 0,275 LT, 0,33 LT 0,5 LT AND 0,75 LT BOTTLES WITH CROWN CAPS OR SCREW CAPS: - NEW GLASS AND CANS DEPALLETIZER, MAKE KÖNIG, TYPE: M-0-00.5086/1, CHUTE MACHINE, BUILT 2000, IN OPERATING FOR THE GLASS LINE AND THE CANNING LINE (INTERIM LAYER LIFT OFF IS OUT OF OPERATION - LINEAR-RINSER, MAKE SFT STEINLE FÖRDERTECHNIK AUGSBURG, INLET AT TOP, OUTLET BELOW, FREQUENCY CONTROLLED, COMPLETE IN STAINLESS STEEL, BUILT 1997 - METAL INSPECTION, MAKE HEUFT - BOTTLE FILLER, MAKE H+K/KHS, TYPE: VVF 80/12/12, SINGLE PRE-EVACUATION, REBUILT IN 1997 FROM HORMES, WITH CROWN CAPPER AND SCREW CAPPER FOR PLASTIC CAPS, VACUUM PUMP, BEER REGULATION LINE, HDE, LEFT->RIGHT - FILL HEIGHT INSPECTING, MAKE HEUFT, TYPE: BASIC, BUILT 2003 - LABELER, MAKE CAVAGNINO & GATTI, FOR 10.000 BPH, FOR SELF-ADHESIVE LABEL WITH 3 AGGREGATE FOR FRONT-, BACK- AND NECK LABEL, BUILT 2009, WITH FREE STANDING CONTROL DESK - CAP SET UP - TRAY-ERECTOR, MAKE KETTNER, BUILT 1994 - SHRINK PACKER, MAKE DOBOY, TYPE: SW 83-D, BUILT 1980 - FLASH PASTEURIZER, MAKE ALFA LAVAL, TYPE: N-35, FOR 100 HL/H, 3-STAGE, WITH BACK COOLING ZONE, HOT HOLDING ZONE, BUILT 2005 - CHAMBER PASTEURIZER, MAKE RICO, FOR 2 PALLET, COMPLETE OVERHAULED IN 2003 - 1 CIP-TUB 7. CANNING LINE FOR 250 ML SLIM-LINE CANS FOR BEER AND CARBONATED SOFTDRINKS, FORMAT PARTS FOR 330/500 LT CANS TYPE 202, PARTLY EXISTING: - RINSER, MAKE TRANS TECH HYSEK, TYPE: CANJET 2575, 2-CHANNEL RINSER WITH CAN TURNER AFTER THE RINSER, BUILT 2000 - FILLER, MAKE NOLL (KHS), WITH 16 FILLING VALVES, UNDERCOVER GASSING, BUILT 1982 - SEAMER, MAKE FERRUM, TYPE: F160, WITH 6 HEADS, BUILT 1981 - FILL HEIGHT INSPECTION, MAKE HEUFT, TYPE: BASIC, BUILT 2005 - CAN WARMER / PASTEURIZER, MAKE ENZINGER, TYPE: PS 4500, WITH 3 ZONES, IN STAINLESS STEEL, WITH EDELSTAHL, WITH WIRE HOOP HINGE BELT, BUILT 1982 - MULTIPACKER, MAKE SMI, TYPE: MP 100 RD, FOR 4/6 PACKS WITH CARDBOARD - „AIR-KNIFE“, MAKE SONIC SYSTEMS - CONVEYORS 8. KEG-WASHER/FILLER KEG-PLANT MAKE MALEK MB KEG TECHNOLOGIE, TYPE: TWIN 3, WITH 2 HEADS, 1 X CLEANING HEAD AND 1 X FILLING HEAD, PRESSING FROM TOP, CURRENTLY TRIANGULAR FITTING, 3 MEDIA FILTER, WITH 1 DETERGENT TUB, BUILT 2003 9. SYRUP ROOM - SUGAR DISSOLVING TANK, IN STAINLESS STEEL, WITH AGITATOR - 5 MIXING TANKS, STAINLESS STEEL, DIFFERENT CONTENTS, OF THEM 1 LYING TANK 8 HL ISOLATED - PREMIXER, MAKE HORMES, FOR 200 HL/H, REBUILD IN 1997 FROM HORMES - PLATE FILTER, MAKE STRASSBURGER, 40X40, WITH 45 PLASTIC PLATES - BAG FILTER - 3 PUMPS: MONO PUMP, MOBILE PUMP WITH SWITCH 10. BAG-IN-BOX-FILLING AUTOMATIC BIB-PLANT WITH: - CARTON ERECTOR, MAKE CERMEX - FILLER, MAKE SMURFIT - CARTON CLOSER, MAKE CERMEX - MANUAL BIB-FILLER, MAKE ALFA LAVAL, TYPE: PICCOLO, BUILT 2011 11. APPLE / BERRY JUICE PRODUCTION - APPLE CRUSHER, MAKE VORAN, BUILT 2011 - BERRY CRUSHER, MAKE BUCHER, BUILT 2011 - APPLE PRESS, MAKE BUCHER, TYPE: XPLUS 40 M, BUILT 2011 - HOLDING TANK - PUMPS - 2 STORAGE TANKS FOR JUICE IN STAINLESS STEEL, EACH 30.000 LT, WITH AGITATOR, NON-PRESSURE 12. TECHNICAL UNITS 12.1 COLD SUPPLY - GLYCOL COOLING, MAKE CARRIER, WITH 2 COMPRESSORS, R22, BUILT 1997 - WATER COOLED CONDENSER, BUILT 1997 12.2 STEAM SUPPLY - STEAM KETTLE, FOR 2 TO. STEAM/H, 12 BAR, WITH WEIßHAUPT-GAS-BURNER, CONDENSATE-TANK AND CHIMNEY, BUILT 1997 13. LABORATORY EQUIPMENT - BEER ANALYSER, MAKE ANTON PAAR, TYPE: SP-1 AUTO SAMPLER - TURBIDMETER - O2 IN HEADSPACE CONTROL MAKE ZAHM & NAGEL - CO2 MEASURING, MAKE HAFFMANS, TYPE: GEHALTEMETER 14. OTHERS - PALLETIZER, MAKE KETTNER, FOR TRAYS ON EURO-PALLET, COMPLETELY OVERHAULED, NOT USED - STERILE FILTER, MAKE PALL, TYPE: CFS, FOR 100 HL/H, NOT IN USE, BUILT 1998 - VARIOUS NEW AND NOT USED CONVEYORS - VARIOUS CARTRIDGE FILTERS - VARIOUS PUMPS - CARLSBERG-FLASK FOR YEAST PROPAGATION - VARIOUS SMALL TANKS QUANTITY AVAILABLE: 1 Learn More