Search results for: 'control panel''

T-9483 FULLY AUTOMATIC FOUR EDGE-SEALING GAUZE PACKING MACHINE TECHNICAL PARAMETERS: BAG SIZE: BASED ON CUSTOMER'S REQUEST SPEED: 120~180 BAGS/MIN PACKING MATERIAL: PAPER+PAPER, PAPER+PLASTIC IT CAN HOT SEALING PACKING MATERIAL, PACKAGE MATERIAL DIAMETER Φ ≤ 350mm, WIDTH IS BASED ON CUSTOMER'S REQUEST; VOLTAGE: 3P 380V 50Hz SERVO MOTOR 1.5 KW+SERVO MOTOR: 1 KW+STEPPING MOTOR 110 + STEPPING MOTOR 130 + VARIABLE FREQUENCY MOTOR 0.37KW, TOTALLY 5 MOTORS ARE 4KW USING 28 VOLT SERIES CIRCUIT HEAT, 2 HEATING PANELS, EACH PANEL HAVE 8 PCS HEATING TUBE, EACH TUBE 300W, TOTALLY 4.8KW MACHINE WEIGHT: 800 KG MACHINE SIZE: LENGTH 5000 X WIDTH 1300 X HEIGHT 1600mm WOODEN CARTON SIZE: LENGTH 2600 X WIDTH 1900 X HEIGHT 1800mm Learn More

REFERENCE NUMBER: M-0180 AUTOMATIC VACUUM PILLOW MACHINE 001E RAW MATERIAL & CASE FABRIC MATERIAL APPLICATION: FOR CONJUGATE HOLLOW SILICONIZED POLYESTER FIBER SHORTER THAN 100mm MICRO FIBER SHORTER THAN 100mm ELASTIC FIBER SHORTER THAN 100mm PILLOW FABRIC QUALITY: PERMEABLE FABRIC LENGTH: 13 METERS LONG QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4796 (11111575DJQ10RX) L COMPLETE BREWERY 65HL INCLUDING FILLING LINES AND KEG LINE DELIVERY OF ONE 65 HL BREWERY WITH THE FOLLOWING EQUIPMENT: 1. MALT HANDLING - MALT ACCEPTANCE BY BIG PACKS - MALT ELEVATOR TO CONDITIONING TANK - GRIST CASE - MALT MILL, MAKE STEINECKER, TYPE: MAISCHOMAT 3003, WET MALT MILL, BUILT 1997 2. BREWHOUSE EQUIPMENT 3-KETTLE-STEINECKER-BREWHOUSE WITH 65 HL CAST WORT, COMPLETE IN STAINLESS STEEL, DRIVES FROM BELOW, AUTOMATED, WITH SIEMENS S5 CONTROL, BUILT 1997 - MASH TUN WITH MASHING FROM BELOW, BOTTOM HEATING ZONE, MASH PUMP, Ø: ~2.500mm - LAUTERTUN, WITH 2-ARM RAKING MACHINE, STAINLESS STEEL KNIFES, 6-PARTED STAINLESS STEEL FALSE BOTTOM, RING LAUTERIG, FALSE BOTTOM RINSING, SPENT GRAINS FALL PIPE, FLOW METER, LAUTER PUMP, Ø: ~2.500mm - WORT KETTLE / WHIRLPOOL, WITH INTERNAL COLANDRIA, WITH TANGENTIAL INLET, SPRAYBALL, WORT PUMP, ~2.500mm - AUTOMATED CONTROL OVER PC FOR BREWHOUSE UNTIL FERMENTING CELLAR AND CIP - ELECTRICAL CONTROL CABINETS - STEEL CONSTRUCTION BETWEEN THE VESSELS - HOT WATER TANK, 200 HL CONTENT, IN STAINLESS STEEL, ISOLATED, HORIZONTAL, STEAM HEATED, WITH MANWAY, MEASUREMENTS: Ø: 2.400 mm x L: 5.700 mm x H: 2.800 mm, WITH PLATE HEAT EXCHANGER, FREQUENCY CONTROLLED PUMP, CONTROL CABINET - COLD WATER TANK, HORIZONTAL, ~150 HL CONTENT, IN STAINLESS STEEL, ISOLATED, WITH MANWAY, MEASUREMENTS: Ø: 2.300mm x L: 4.000mm x H: 2.400mm, WITH PLATE HEAT EXCHANGER, PUMP, CONTROL CABINET - 1 CIP-TUB 3. WORT COOLING - WORT COOLER, MAKE SONDEX, TYPE: S38-FG, 1-STAGE, FOR ICE WATER, 6 BAR, 0,130°C, FLOW METER, BUILT 1998 - WORT AERATION 4. FERMENTING- + STORAGE CELLAR - 9 CYLINDER-CONICAL FERMENTING- AND STORAGE TANKS, INDOOR-CCTS, MAKE HOLVRIEKA, WITH EACH 300 HL GROSS CONTENT, 0,99 BAR, STANDING ON 4 FEET, WITH 3 COOLING ZONES 2 OF THEM IN THE WALL AND 1 CONE COOLING ZONE, WALL ISOLATED WITH PU-FOAM WITHOUT COVERING, CONE ISOLATED AND COVERED, WITH SCANDI BREW ARMATURES, SAMPLER, CLEAR AND REST OUTLET, HEIGHT: ~ 7.500mm, Ø: ~2.900mm, BUILT 1997 - 2-TANK-CIP-PLANT, AUTOMATED, ONLY FOR THE CCTS, IN STAINLESS STEEL, WITH LID, LEVEL DISPLAY, PIPING, PUMP, AUTOMATIC APV VALVES - 2 PANEL, WITH SWIVELLING BOWS - PUMPS - CARLSBERG FLASK FOR YEAST PROPAGATION FROM SCANDI BREW - 1 YEAST TUB, ABOUT 100 LT, IN STAINLESS STEEL, WITH LID, AS TRANSFER TUB - YEAST PUMP, MOBILE 5.1 FILTERCELLAR 100 HL/H - KIESELGUHRFILTER, MAKE SCHENK, TYPE: ZHF-S25, FOR 100 – 125 HL/H WITH OPERATING PLATFORM, HYDRAULIC DRIVE, HYDRAULIC AGGREGATE, STANDING ON BASIS FRAME, BUILT 1989, GRATING, CONTROL CABINET - KIESELGUHR DOSAGE, WITH AGITATOR, LID, DOSAGE PUMPE, PRECOATING PUMP - DOSAGE TUB WITH AGITATOR AND PUMP, MOBILE, WITH PLUG - ROOM AIR EVAPORATOR WITH 2 FAN 5.2 BBT CELLAR - 3 STAINLESS STEEL BRIGHT BEER TANKS / BBTS, MAKE HOLVRIEKA, EACH 140 HL, 1 TANK WITH 1,5 BAR, 2 OF THEM WITH 1,0 BAR BUILT 1997, MOULDED BOTTOM TANKS, NOT COOLABLE, STANDING ON 4 FEET, WITH MANWAY, SPRAY HEAD, PULLED DOWN CLEANING PIPE, SAMPLER, MANOMETER, Ø: 1.500 mm, BUILT 1998 - BEER PUMP - PANEL, MAKE PALL - 1 CIP-TUB, MANUAL, WITHOUT LID, STANDING ON 3 FEET, ~100 LT CONTENT, PUMP - CO2 MEASURING UNIT MAKE HAFFMANS, MOBILE 6. COMBINATED BOTTLING LINE, NON RETURNABLE BOTTLES AND CANNING LINE FILLING LINE FOR NON RETURNABLE GLASS BOTTLES FOR 0,275 LT, 0,33 LT 0,5 LT AND 0,75 LT BOTTLES WITH CROWN CAPS OR SCREW CAPS: - NEW GLASS AND CANS DEPALLETIZER, MAKE KÖNIG, TYPE: M-0-00.5086/1, CHUTE MACHINE, BUILT 2000, IN OPERATING FOR THE GLASS LINE AND THE CANNING LINE (INTERIM LAYER LIFT OFF IS OUT OF OPERATION - LINEAR-RINSER, MAKE SFT STEINLE FÖRDERTECHNIK AUGSBURG, INLET AT TOP, OUTLET BELOW, FREQUENCY CONTROLLED, COMPLETE IN STAINLESS STEEL, BUILT 1997 - METAL INSPECTION, MAKE HEUFT - BOTTLE FILLER, MAKE H+K/KHS, TYPE: VVF 80/12/12, SINGLE PRE-EVACUATION, REBUILT IN 1997 FROM HORMES, WITH CROWN CAPPER AND SCREW CAPPER FOR PLASTIC CAPS, VACUUM PUMP, BEER REGULATION LINE, HDE, LEFT->RIGHT - FILL HEIGHT INSPECTING, MAKE HEUFT, TYPE: BASIC, BUILT 2003 - LABELER, MAKE CAVAGNINO & GATTI, FOR 10.000 BPH, FOR SELF-ADHESIVE LABEL WITH 3 AGGREGATE FOR FRONT-, BACK- AND NECK LABEL, BUILT 2009, WITH FREE STANDING CONTROL DESK - CAP SET UP - TRAY-ERECTOR, MAKE KETTNER, BUILT 1994 - SHRINK PACKER, MAKE DOBOY, TYPE: SW 83-D, BUILT 1980 - FLASH PASTEURIZER, MAKE ALFA LAVAL, TYPE: N-35, FOR 100 HL/H, 3-STAGE, WITH BACK COOLING ZONE, HOT HOLDING ZONE, BUILT 2005 - CHAMBER PASTEURIZER, MAKE RICO, FOR 2 PALLET, COMPLETE OVERHAULED IN 2003 - 1 CIP-TUB 7. CANNING LINE FOR 250 ML SLIM-LINE CANS FOR BEER AND CARBONATED SOFTDRINKS, FORMAT PARTS FOR 330/500 LT CANS TYPE 202, PARTLY EXISTING: - RINSER, MAKE TRANS TECH HYSEK, TYPE: CANJET 2575, 2-CHANNEL RINSER WITH CAN TURNER AFTER THE RINSER, BUILT 2000 - FILLER, MAKE NOLL (KHS), WITH 16 FILLING VALVES, UNDERCOVER GASSING, BUILT 1982 - SEAMER, MAKE FERRUM, TYPE: F160, WITH 6 HEADS, BUILT 1981 - FILL HEIGHT INSPECTION, MAKE HEUFT, TYPE: BASIC, BUILT 2005 - CAN WARMER / PASTEURIZER, MAKE ENZINGER, TYPE: PS 4500, WITH 3 ZONES, IN STAINLESS STEEL, WITH EDELSTAHL, WITH WIRE HOOP HINGE BELT, BUILT 1982 - MULTIPACKER, MAKE SMI, TYPE: MP 100 RD, FOR 4/6 PACKS WITH CARDBOARD - „AIR-KNIFE“, MAKE SONIC SYSTEMS - CONVEYORS 8. KEG-WASHER/FILLER KEG-PLANT MAKE MALEK MB KEG TECHNOLOGIE, TYPE: TWIN 3, WITH 2 HEADS, 1 X CLEANING HEAD AND 1 X FILLING HEAD, PRESSING FROM TOP, CURRENTLY TRIANGULAR FITTING, 3 MEDIA FILTER, WITH 1 DETERGENT TUB, BUILT 2003 9. SYRUP ROOM - SUGAR DISSOLVING TANK, IN STAINLESS STEEL, WITH AGITATOR - 5 MIXING TANKS, STAINLESS STEEL, DIFFERENT CONTENTS, OF THEM 1 LYING TANK 8 HL ISOLATED - PREMIXER, MAKE HORMES, FOR 200 HL/H, REBUILD IN 1997 FROM HORMES - PLATE FILTER, MAKE STRASSBURGER, 40X40, WITH 45 PLASTIC PLATES - BAG FILTER - 3 PUMPS: MONO PUMP, MOBILE PUMP WITH SWITCH 10. BAG-IN-BOX-FILLING AUTOMATIC BIB-PLANT WITH: - CARTON ERECTOR, MAKE CERMEX - FILLER, MAKE SMURFIT - CARTON CLOSER, MAKE CERMEX - MANUAL BIB-FILLER, MAKE ALFA LAVAL, TYPE: PICCOLO, BUILT 2011 11. APPLE / BERRY JUICE PRODUCTION - APPLE CRUSHER, MAKE VORAN, BUILT 2011 - BERRY CRUSHER, MAKE BUCHER, BUILT 2011 - APPLE PRESS, MAKE BUCHER, TYPE: XPLUS 40 M, BUILT 2011 - HOLDING TANK - PUMPS - 2 STORAGE TANKS FOR JUICE IN STAINLESS STEEL, EACH 30.000 LT, WITH AGITATOR, NON-PRESSURE 12. TECHNICAL UNITS 12.1 COLD SUPPLY - GLYCOL COOLING, MAKE CARRIER, WITH 2 COMPRESSORS, R22, BUILT 1997 - WATER COOLED CONDENSER, BUILT 1997 12.2 STEAM SUPPLY - STEAM KETTLE, FOR 2 TO. STEAM/H, 12 BAR, WITH WEIßHAUPT-GAS-BURNER, CONDENSATE-TANK AND CHIMNEY, BUILT 1997 13. LABORATORY EQUIPMENT - BEER ANALYSER, MAKE ANTON PAAR, TYPE: SP-1 AUTO SAMPLER - TURBIDMETER - O2 IN HEADSPACE CONTROL MAKE ZAHM & NAGEL - CO2 MEASURING, MAKE HAFFMANS, TYPE: GEHALTEMETER 14. OTHERS - PALLETIZER, MAKE KETTNER, FOR TRAYS ON EURO-PALLET, COMPLETELY OVERHAULED, NOT USED - STERILE FILTER, MAKE PALL, TYPE: CFS, FOR 100 HL/H, NOT IN USE, BUILT 1998 - VARIOUS NEW AND NOT USED CONVEYORS - VARIOUS CARTRIDGE FILTERS - VARIOUS PUMPS - CARLSBERG-FLASK FOR YEAST PROPAGATION - VARIOUS SMALL TANKS QUANTITY AVAILABLE: 1 Learn More

TT-4766 SCHRAMM T685WS-C DRILLING RIG, YEAR 2008 SCHRAMM T685WS-C DRILLING RIG CONDITION USED YEAR 2008 QUANTITY: 1 Learn More

REFERENCE NUMBER: M-4566 (1111225RSJ10U) L THERMOPLASTIC HOTMELT COATING LINE MP ENGINEERING TYPE HM59-SD3 YEAR 2005 WIDTH 102” (2590mm) YEAR: 2005 TYPE: HM59-SD3 MATR: 404/04 ROLL FACE: 2600mm (102”) WORKING WIDTH: 2400mm (95”) VOLTAGE: 480/3/60 CONTROL VOLTAGE: 110/60 CONSISTING OF: CAROUSEL 3 POSITION LET-OFF, ENTRY ON ACCUMULATOR WITH HOT-WIRE SEAMING DEVICE, 8000 VOLT STATIC ELIMINATOR, PNEUMATICALLY OPERATED FABRIC HOLDING DEVICE FOR TENSION CONTROL, ACCUMULATOR WITH 8-ROLLS UP AND 9-ROLLS DOWN APPROX.. 80-YARD CAPACITY, COMPENSATING ARM ON EXIT SIDE. ROLLS ARE 4” DIA. X 102” FACE ALUMINUM, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. SECOND ACCUMULATOR WITH ROLL CRADLE FOR SECOND SUBSTRATE LET-OFF, ACCUMULATOR WITH 9-ROLLS UP AND 10 ROLLS DOWN, APPROX.. 54 YARD CAPACITY, ROLLS ARE 4’ DIA. X 102” FACE ALUMINUM, INCLUDES 8000 VOLT STATIC ELIMINATOR AND PNEUMATIC FABRIC HOLDING FOR TENSION, PENDULUM TYPE GUIDING DEVICE ON EXIT SIDE, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. OVERHEAD GANTRY WITH ACCESS STAIRS ON RIGHT SIDE OF FIRST ACCUMULATOR, EXTENDS OVER THE EXTRUDER WITH JIB MOUNTED FOR EASE IN REMOVING DIE FROM MACHINE, GUIDING/CENTERING DEVICE MOUNTED ONTO GANTRY FEEDING COATING HEAD. MP ENGINEERING EXTRUDER/APPLICATOR TYPE HM59-SD3, MATR. NO. 402/04, WITH 102” DIE, 98” RUBBER-BELT WITH PNEUMATIC CYLINDERS FOR BELT TENSION AND GUIDING, HEATED CYLINDER BACKING TO DIE, OPERATOR PLATFORM, CONTROLS MOUTNED IN DOOR AND OPERATOR TOUCH SCREEN PANEL. (NOTE: THESE ARE PRESENTLY MOUNTED ON PRODUCTION LINE AND WILL BE REMOVED AND PLACED BACK INTO/ONTO APPLICATOR. 480/3/60 COATEM SISTEMI C.R.L. IMBALLAGIO & HOT MELT EXTRUDER, S/N 50701, TYPE/MODEL CE-200, WITH DIGITAL MICROPROCESSOR AND INVERTER FOR SPEED VARIATION, DESIGNED TO WORK MAINLY WITH POLYESTER, POLYAMIDE AND POLYURETHANE BUT CAN ALSO EXTRUDE ABS, POLYTHENE, POLYPROPYLENE AND ADHESIVES LIKE EVA ADHESIVES. 480/3/60 CONAIR DRYER CD-300, PL-D-196-1, MODEL D03H4101310, S/N 9D0597, 480/3/60, AND HOPPER. THIRD ACCUMULATOR FOR BONDED PRODUCT WITH 6-ROLLS UP AND 7-ROLLS DOWN, APPROX…60-YARD CAPACITY, ROLLS ARE 6” DIA. X 102” FACE ALUMINUM, WITH DRAW-ROLL TENSION DEVICE MOUNTED ONTO EXIT, OVERHEAD CARRIER ROLLS AND FRAMEWORK DELIVERY TO ELECTRIC A-FRAME WINDER WITH 102” FACE LAY-ON ROLL, AND SEMI-AUTOMATIC BATCHER FOR INDIVIDUAL ROLLS, 2-ROLL SURFACE WINDING 102” FACE WIDTH, OVERHEAD CORE FEED, FABRIC CENTERING DEVICE, ELECTRIC SCISSOR CUT-OFF, KICK-OUT TO 2-ROLL BED, OPERATOR PLATFORM AND OPERATOR CONTROLS. ALL MACHINES PRODUCED BY MP CONFORMS TO EEC DIRECTORY 89/392 CEE (CE MARK) TECHNICAL FEATURES OF THE LINE, ACCORDING TO DWG 100-904/1C ROLLERS WIDTH 2600mm WORKING WIDTH 2400mm MAXIMUM DIAMTER OF THE ROLLS OF PU FOAM 1500mm MAXIMUM DIAMETER OF THE UNWOUND ROLLS OF FABRIC 600 ° 1500 MAXIMUM DIAMETER OF THE REWOUND ROLLS 500 ° 1500 (IN CASE YOU ARE REWINDING ROLLS OF FABRIC LAMINATED TO PU FOAM, THE MAXIMUM DIAMETER IS 1750mm) ADJUSTABLE MECHANIC SPEED: 5 TO 50 M/MIN MAIN POWER SUPPLY + NEUTRAL + EARTH 480+N+E/60 V/HZ VOLTAGE ON CONTROL PANELS 110/60 V/HZ INSTALLED POWER FOR MOTORS 22KW INSTALLED POWER FOR IR HEATER 14,25KW INSTALLED POWER TO HEAT THE SLOT-DIE 32KW INSTALLED POWER FOR THE THERMAL OIL HEATING UNIT FOR THE CALENDERING ROLLERS 32,2KW INSTALLED POWER FOR THE CHILLER 12,9KW A.C. MOTORS, DRIVER, ELECTRIC CABLES ARE ACCORDING TO CEI NORMS BACKGEAR ROLLERS, WITH PAINTED SURFACE OR ALUMINUM MADE WITH DIAMETER 100/120/150mm COMPRESSED AIR CONSUMPTION, AT 6 BAR 1500LT/H COOLING WATER CONSUMPTION (WATER MUST HAVE A TEMPERATURE NOT HIGHER THAN 10°C) 5500LT/H ADJUSTABLE TENSION ON THE REWOUND MATERIALS 5 A 35 KG. PAINTING GREEN RAL 6027 E BLUE MARINE RAL 5021 A.C. MOTORS CONTROL THE SPEED OF THE MACHINES, AND ARE AUTOMATICALLY SYNCHRONISED THROUGH ELECTRONIC DRIVES (INVERTER) AND PNEUMATIC DANCER UNITS (COMPENSTAORS) ESTRUDER: CAPACITY UP TO 200 KG/H (DEPENDING ON THE VISCOSITY OF THE ADHESIVE TO BE EXTRUDED) POWER OF THE MOTOR AND RESISTANCES: 90KW MAXIMUM MELTING TEMPERATURE: 220°C MATERIALS TO BE PROCESSED NONWOVENS 30:150 GR/M2 SYNTHETIC AND NATURAL FABRICS (EXCLUDING STRETCHY FABRICS) WITH WEIGHT 100:600 GR/M2 SCRIMS FOR BACKING FABRIC WITH WEIGHT 70:120 G/M2 MAXIMUM THICKNESS OF PU FOAM 15mm MINIMUM THICKNESS OF PU FOAM 2mm DENSITY OF PU FOAM 22/40 KG/M3 THERMOPLASTIC ADHESIVE TO BE COATED THERMOPLASTIC HOTMELTS (COPOLYAMMIDE, COPOLYESTER, EVA AND POLYURETHANE THERMOPLASTIC HOTMELT GRANULES) DATA REFERRING TO PRODUCTION THE PRODUCTION SPEED CAN CHANGE, DEPENDING ON THE KIND OF HOTMELTS, ON THEIR MELTING TEMPERATURE, ON THEIR VISCOSITY, AND ON THE GRAMS PER SQUARED METER TO BE COATED QUANTITY AVAILABLE: 1 Learn More

TT-8506 DAVIS STANDARD 60IN60TPIH 30 TO 1 500 HP VENTED EXTRUDER, 6 INCHES 1. EXTRUDER MAKE: DAVIS STANDARD 2. EXTRUDER MODEL: 60IN60TPIH 3. REBUILD STATUS: REBUILT QUANTITY: 1 Learn More

REFERENCE NUMBER: K-9326 BABCOCK WIDE TENTER FRAME 144" (3657mm) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5244 (1313JTBVXX12) L TOYOTA JAT610 AIR JET LOOMS YEAR 1998 WIDTH 1900mm-2800mm TOYOTA JAT610 AIR JET LOOMS, YEAR 1998 (60 LOOMS) X WIDTH 1900mm (12 LOOMS) X WIDTH 2800mm RUNNING CONDITION YEAR 1999 1 INVERTER FOR 36 LOOMS (2 INVERTERS FOR ALL 72 LOOMS) QUANTITY AVAILABLE: 27 LOOMS Learn More

REFERENCE NUMBER: M-1976 (770395POK6RM) BABCOCK FRAME 144" WIDE-3600mm QUANTITY AVAILABLE: 1 Learn More

YY-3260 GENERATOR SET WARTSILA 1 X 12V32LN DG 4.2 MW, 750 RPM, 11KV VOLT, 50Hz. POWER PLANT FOR SALE GOOD RUNNING TAKEOUT GENERATOR SET WARTSILA 1 X 12V32LN DG 4.2 MW, 750 RPM, 11KV VOLT, 50Hz. POWER PLANT FOR SALE. Learn More