TT-4766 SCHRAMM T685WS-C DRILLING RIG, YEAR 2008

REFERENCE NUMBER: TT-4766 SCHRAMM T685WS-C DRILLING RIG, YEAR 2008 SCHRAMM T685WS-C DRILLING RIG CONDITION USED YEAR 2008 T685WS TRUCK MOUNTED TOP HEAD ROTARY RIG THIS RIG IS IN GOOD WORKING CONDITION, AN INSPECTION REPORT OF NECESSARY MAINTENANCE/REPAIR CAN BE PROVIDED. EXPLORATION - SHALLOW OIL - WATER WELL MILEAGE: 6,847 MILES (11,020 KM) THE T685WS-C IS THE DRILLING CONTRACTOR’S RIG OF CHOICE FOR MINERAL EXPLORATION, SHALLOW OIL AND DEEP WATER WELL APPLICATIONS. HEAVY DUTY FACTORY INSTALLED COMPONENTS AND ACCESSORIES ARE AVAILABLE TO MEET A WIDE RANGE OF ARCTIC, DESERT AND TROPICAL CONDITIONS. ANY CLIMATE, ANY TERRAIN, SCHRAMM RIGS ARE BUILT YOUR WAY, DELIVERING MAXIMUM PERFORMANCE AND RELIABILITY IN THE MOST EXTREME ENVIRONMENTS ON EARTH. DRIVE ENGINE CUMMINS ISM-400 ENGINE (400HP) DECK ENGINE CUMMINS QSK 19-C DECK ENGINE TIER 1 (755 HP) 220 GALLONS (832 L) FUEL TANK CAPACITY STANDARD COMPRESSOR VARIABLE VOLUME, TWO-STAGE, OIL FLOODED ROTARY SCREW MODEL 1350/350 1350 SCFM AT 350 PSIG & 1800 RPM AIR PRESSURE/RATED MAX 1350 500 PSIG MECHANICAL CLUTCH SCHRAMM PATENTED AIR-CONTROL® COOLING 122°F (50°C) AMBIENT DESIGN TEMPERATURE VARIABLE SPEED COOLING FAN CONTROL SYSTEM LOCATED ON THE LEFT-HAND SIDE, THE SWING-OUT CONTROL PANEL STORES UNDER THE MAST FOR TRANSPORT DIGITAL DISPLAY ON DRILLER’S CONTROL PANEL INCLUDES TACHOMETER, OIL PRESSURE, OIL TEMP., WATER TEMP., AND VOLTMETER WITH SEPARATE HOUR METER GAUGES INCLUDE COMPRESSOR DISCHARGE TEMP., AIR PRESSURE, INTERSTAGE PRESSURE, ROTATION PRESSURE, HOLDBACK PRESSURE, DOWN FEED PRESSURE, WATER INJECTION AND LUBRICATOR PRESSURE TRUCK STANDARD TRUCK: INTERNATIONAL 7600 8X4 20,000 IB (9,072 KG) FRONT AXLE 20,000 IB (9,072 KG) PUSHER AXLE 46,000 IB (20,866 KG) FULL LOCKING REAR AXLE 86,000 IB (39,010 KG) GVWR TOP HEAD DRIVE HEAVY DUTY, SINGLE REDUCTION GEARBOX WITH DISC VALVE, LOW SPEED, HIGH TORQUE HYDRAULIC MOTORS INFINITELY VARIABLE ROTATION SPEED VIA HRC CONTROL SPINDLE THRU HOLE: 5.25-INCH ID (133.3mm) MAXIMUM TORQUE: 12,565 FT-LBS (17,083 N-M) ROTATION SPEED: 0-104 RPM OUTRIGGERS DUAL FRONT – 4-INCH (102mm) BORE X 41-INCH (1.04 M) STROKE DUAL REAR – 5-INCH (127mm) BORE X 41-INCH (1.04 M) STROKE FEED SYSTEM TOP HEAD DRIVEN BY HYDRAULIC CYLINDERS THROUGH HEAVY ROLLER CHAIN 30 FT (9.1 M) HEAD TRAVEL 94,000 IBF (428 KN) PULLBACK 113 FPM (34.4 M/MIN) PULLBACK SPEED 28,000 IB (124.5 KN) PULLDOWN 89 FPM (27.1 M/MIN) PULLDOWN SPEED SLOW FEED DRILLUP VALVE SLIDING ANGLE MAST TUBULAR STEEL, ALL WELDED, LATTICE TYPE STRUCTURE OPERATING ANGLE: 0-45° MANUALLY LOCKS IN 5° INCREMENTS MAST SLIDE TRAVEL: 8 FT (2.44 M) DRILL TABLE TABLE OPENING: 22 IN (560mm) HYDRAULIC HOLDING FORK EXPLORATION JIB BOOM FOR HANDLING DRILL PIPE ON ANGLES UP TO 45° FROM VERTICAL, AN EXTENDED DIPPER STICK IS MOUNTED TO A (SWING AND EXTEND) HYDRAULIC JIB BOOM SWINGS: 140° EXTENDS: 40 IN (1.02 M) CAPACITY: 1,000 IBF (4.45 KN) VERTICAL PULL WINCH 9,600 IBF (42.7 KN) BARE DRUM LINE PULL (DERATED WHEN USED WITH EXPLORATION JIB BOOM) 216 FPM (66 M/MIN) BARE LINE SPEED PLANETARY DESIGN WITH SPRING APPLIED HYDRAULIC RELEASE BRAKE HYDRAULIC SYSTEM OPEN LOOP LOAD SENSING SYSTEM 160-GALLON (606 I) SYSTEM CAPACITY 7-MICRON FILTRATION WATER INJECTION SYSTEM 25 GPM (95 IPM) WATER PUMP 13.2 MAXIMUM GPM (50 IPM) FOAM PUMP 800 PSI (55 BAR) TOOL LUBRICATOR POSITIVE DISPLACEMENT, AIR OPERATED PISTON TYPE PUMP VARIABLE TO 5.0 GPH (19 IPH) LIGHTING & ELECTRICAL SYSTEM - 24 VOLT MAST - (3) 60-WATT FLOODLIGHTS CONTROL PANEL - (2) FLOODLIGHTS WORK - (3) 70-WATT HALOGEN QUANTITY: 1