Search results for: 'reference number -v-21'

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-4426 SLAUGHTER LINE FOR CATTLE (300 PD) AND SHEEP (1000 PD) QUANTITY AVAILABLE: 1 Learn More

TT-2153 SIEMENS SGT-800 GAS TURBINE, 54 MW, 11 KV, 50 Hz AND 1500 RPM, FUEL NATURAL GAS, FREQUENCY 50/60 Hz GROSS EFFICIENCY 38.86.0% HEAT RATE9, 256 KJ/KWH UNUSED CONDITION: EXCELLENT (NEW SURPLUS) TURBINES STORED TO SIEMENS RECOMMENDATION. NOTE: THIS IS A PACKAGE DEAL AND REQUIRES BUYER TO PURCHASE ALL 3 UNITS. POI AND POF REQUIRED UPFRONT. QUANTITY: 3 Learn More

REFERENCE NUMBER: M-0428-SHORT VERSION CATTLE SLAUGHTERING AND PROCESSING EQUIPMENT FOR 200 CATTLES PER DAY 200 CATTLES PER DAY QUANTITY AVAILABLE: 1 Learn More

C-3994 BARGEMOUNTED POWER PLANT, CAPACITY 220MW

A. ONCE THROUGH STEAM GENERATOR
B. BARGE
C. CHILLERS
D. AIR COMPRESSOR
E. GAS TURBINE
F. STEAM TURBINE
G. FEEDWATER SYSTEM
H. CLOSED COOLING WATER SYSTEM
I. AUXILIARY COOLING WATER SYSTEM
J. CONDENSATE POLISHING UNIT (CPU)
K. WASTE WATER SYSTEM
L. PLANT ELECTRICAL SYSTEM
M. BLACK START DG SET
N. PLANT CONTROLS AND INSTRUMENTATION
O. PLANT FIRE FIGHTING SYSTEM
P. START UP VACUUM SYSTEM
Q. STEAM TURBINE DEAERATING CONDENSER

QUANTITY: 1 PLANT

Learn More

REFERENCE NUMBER: F-1227 EPS BLOCK (6000×1200×600mm) PRODUCTION LINE (NEW) CONSIST OF: 1. EPS BATCH PRE-EXPANDER MODEL SJ1400 2. EPS AUTO AIR-COOLING BLOCK MOLDING MACHINE SB6000 3. EPS CUTTING MACHINE PSC6000 4. CNC CUTTING MACHINE SCS3000 5. AUTO SHAPE MOLDING MACHINE WITH VACUUM SZ-172 6. AUXILIARY EQUIPMENT QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: V-0025 COTTON PAD, BALL, SWAB MACHINES M-5138 SQUARE COTTON PAD PRODUCTION MACHINE M-5139 COTTON GAUZE PAD PRODUCTION MACHINE M-5140 MACHINE TO PRODUCE VARIOUS TYPES OF COTTON PADS M-5141 COTTON PAD PRODUCTION MACHINE M-5142 MAKEUP REMOVING COTTON PAD PRODUCTION MACHINE M-5143 ROUND COTTON PAD MAKING MACHINE M-5144 SQUARE ABSORBENT COTTON PAD PRODUCTION MACHINE M-5145 ROUND ABSORBENT COTTON PAD PRODUCTION MACHINE M-5146 ROUND COTTON PADS MAKING MACHINE M-5147 COTTON PAD MAKING MACHINE M-5148 COTTON PAD MAKING MACHINE M-5168 COTTON PADS MAKING MACHINE M-5169 COTTON Q-TIP MAKING MACHINE (100PCS/BAG) M-5170 COTTON BALL MAKING MACHINE (NEW) M-5171 COSMETIC COTTON PAD (GLOVE SHAPE) MAKING MACHINE M-5172 COSMETIC COTTON PAD MAKING MACHINE (ROUND PAD) M-5101 MEDICAL COTTON BALL MAKING MACHINE 20KG/HOUR QUANTITY AVAILABLE: 17 Learn More

P-5039 COMPLETE PLANT WITH DYEING – FINISHING – WEAVING - SEWING

PLAIN DYEING AND FINISHING EQUIPMENT:
7 DYEING MACHINES
9 AUTOMATIC DOSING SYSTEM
10 DYEING MACHINE – JIGGER
11 DYEING MACHINE – JIGGER
15 INSPECTION MACHINE
16 MACHINES FOR BONDING PIECES (GOODS)
18 WINDING MACHINE
19 INSPECTION MACHINE
20 MEASURING WINDING MACHINE
21 HEAT EXCHANGER
DOUBLING MACHINE

YARN DYEING AND DRYING:
1 DYEING APPARATUS
2 DYEING APPARATUS
3 DYEING APPARATUS
4 PRESSURE DRYING APPARATUS – TANDEM
5 DYEING APPARATUS
6 DYEING APPARATUS
7 THE LOADING AND UNLOADING DEVICE
8 BRIDGE CRANE
9 PROCESS WATER REGENERATION + TANK

SEWING:
8 SEWING MACHINE FOR WASHING GLOVES
9 CONTROL TABLES
10 PACKING MACHINES

DOUBLING, TWISTING, WARPING AND WEAVING:
3 WINDING MACHINE
4 MOBILE REGALS FOR YARN STORAGE

WARPING AND WEAVING:
1 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
2 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
3 WARPING MACHINE
4 SIZING MACHINE
5 SIZING MACHINE
13 COMPRESSOR FOR COMPRESSED AIR
14 KNOTTING MACHINES
15 ELEVATOR FOR BEAMS
16 ELEVATOR FOR BEAMS
17 PUNCH MACHINE
18 ELEVATOR FOR BEAMS
19 MOBILE REGALS FOR BEAM STORAGE

WEAVING SAURER 1;2;3;4:
STAUBLI JACQUARD – WITH 560 HOOKS X 4 – 10 PIECES
STAUBLI JACQUARD – WITH 768 HOOKS X 4 – 4 PIECES
STAUBLI JACQUARD – WITH 1120 HOOKS X 2 - 2 PIECES
STAUBLI JACQUARD – WITH 912 HOOKS X 2 – 1 PIECE

WEAVING SILK:
WEAVING MACHINE – LOOMS SM 93
CONTROL TABLE

READY MADE DEPARTMENT FOR TERRY BATHROBES:
CUTTING TABLE – BULLMERWERK – 1 PIECE
SEWING MACHINE – JUKI – 2 PIECES
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE –LEVIS – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – JUKI – 2 PIECE
SEWING MACHINE – MAUSER SPECIAL – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – 1 PIECE
SEWING MACHINE – NECCHI – 4 PIECES
SEWING MACHINE – PFAFF – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE

LABOR MACHINES:
APPARATUS FOR MEASURING ZTWIST, TURN/ROLL – TORSIOMETER
APPARATUS FOR MEASURING THE FRICTION COEFFICIENT
LIGHTING CHAMBER
AA WINDING APPARATUS FOR THE DYEING TUBE THE SAMPLING DEVICE
WINDING APPARATUS FOR COLOR STANDARDS
YARN DYEING APPARATUS PRETEMA MULTICOLOR
DYNAMOMETER FOR SPINNING
SPEKTROFOTOMETER DATACOLOR INTERNATIONAL – LABOR MACHINE
APPARATUS FOR THE VISUAL APPEARANCE OF THE YARN – LABOR MACHINE

ADDITIONAL DESCRIPTION

PLAIN DYEING AND FINISHING EQUIPMENT:
7. DYEING MACHINE
SCHIRM
MODEL: SURFER
YEAR: 1994
CAPACITY : 380 – 400 KG
TECHNICAL INFORMATION:
WOVEN TERRY DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
SEDOMAT PC 3100
QUANTITY: 1 (NO 94)

9. AUTOMATIC DOSING SYSTEM
LAWER
YEAR: 2002
CHEMICAL DISPENSING SYSTEM
20 PVC TANKS (CAPACITY 200 L TO 1200 L)
2 EXTERNAL TANKS CAPACITY 1500 L
TRANSFER PUMP
QUANTITY: 1

10. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 3000MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR -FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
DIMENSIONS LENGTH 65000 MM X WIDTH 43000 MM X HEIGHT 25000 MM
INSTALLED ELECTRIC POWER: 3 X 63 A
QUANTITY: 1(NO 54)

11. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 1600MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
THE HYDRAULIC SYSTEM HAS FAILED/NOT WORKING
DIMENSIONS LENGTH 5,300 CM X WIDTH 4,300 CM X HEIGHT 2,500 CM
QUANTITY: 1(NO 53)

15. INSPECTION MACHINE
MONFORTS
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

16. MACHINE FOR BONDING PIECES (GOODS)
GEBRUDER DOHLE
MODEL: 799/03
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 2

18. WINDING MACHINE
MARK: AEG
TECHNICAL INFORMATION:
WINDING GOODS
QUANTITY: 1

19. INSPECTION MACHINE
MONFORTS
MODEL: MBH
YEAR: 1977
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

20. MEASURING WINDING MACHINE
MENZEL
MODEL: MWE2
YEAR: 1986
TECHNICAL INFORMATION:
WINDING DIFFERENT LENGTHS OF GOOD
QUANTITY: 1

21. HEAT EXCHANGER
PT-S
YEAR: 2002
TECHNICAL INFORMATION:
RECUPERATION
QUANTITY: 1

23. DOUBLING MACHINE
MODEL: MLH
YEAR: 1975
TECHNICAL INFORMATION:
DOUBLING AND COMPOUNDING GOODS
QUANTITY: 1

YARN DYEING AND DRYING:
1. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN : MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
QUANTITY: 2 PCS (NO 12, NO 14)

2. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 850
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY;
6 INCHES BOBBIN : MAX 144 KG, MIN. 58 KG
5 INCHES BOBBIN : MAX 100 KG, MIN. 42 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
THICKNESS OF PLATE = 30 CM
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2.00 CM
DIMENSIONS: LENGTH 3100MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
INSTALLATION OF THE SOIL = 60CM DEEPER
(APPLY TO ALL INSTALLATION)
QUANTITY: 1(NO 18)

3. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS TYPE 600
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN: MAX 84 KG, MIN. 34 KG
5 INCHES BOBBIN: MAX 59 KG, MIN. 26 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
DIMENSIONS: LENGTH 2500MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC POWER: 17 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
QUANTITY: 1(NO 16)

4. PRESSURE DRYING APPARATUS – TANDEM
JASPER
YEAR: 1998
TECHNICAL INFORMATION:
DIMENSION: LENGTH 290CM WIDTH 3300MM X HEIGHT 1800MM X HEIGHT 2900MM
CUPBOARD FOR ELECTRONICS
LENGTH 250CM X WIDTH 60CM
QUANTITY: 2 TANDEM WORKING AS ONE UNIT

5. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN: MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 98˚ C
PRESSURE: UP TO 4.5 BAR
MANUAL PROCESSOR
DIMENSIONS: LENGTH 2800MM X WIDTH 3100MM X HEIGHT 2500MM X HEIGHT 2900MM
(WITH A DOSING DEVICE IN THE FORM OF "V")
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS: LENGTH 2500MM X WIDTH 60MM
QUANTITY: 1 (NO 13)

6. DYEING APPARATUS
THEN
MODEL: HL 40/7,8
YEAR: 1986
WIDTH: 1800MM
5 INCHES BOBBIN: MAX 12 PIECES
WORKING TEMPERATUR: UP TO 140˚ C
HEIGHT: 2160MM
PRESSURE: UP TO 4,5 BAR
INSTALLED ELECTRIC POWER – 3X16 A
TECHNICALINFORMATION: DYEING APPARATUS
DIMENSIONS: LENGTH 1600MM
QUANTITY: 1

7. THE LOADING AND UNLOADING DEVICE
JASPER
YEAR: 1998
TECHNICAL INFORMATION; LOADING DEVICE FOR BOBBINS
THICKNESS OF PLATE = 300MM (APPLY TO ALL INSTALLATIONS)
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2000MM (APPLY TO ALL INSTALLATION)
DIMENSIONS : Ø 1700MM : HEIGHT1600MM
INSTALLED ELECTRIC POWER : 10KW
QUANTITY: 1

8. BRIDGE CRANE
TECHNICAL INFORMATION:
THE CARGO TRANSFER
QUANTITY : 2

9. PROCESS WATER REGENERATION + TANK
JASPER
TECHNICAL INFORMATION:
STORAGE OF WATER FOR THE PRODUCTION PROCESS
QUANTITY : 1

SEWING:
8. SEWING MACHINE FOR WASHING GLOVES
TEXPA ARBTER
MODEL: WASCHLA 10
YEAR: 1994
TECHNICAL INFORMATION:
SEWING WASHING GLOVES, FITTING LABELS AND CORD.
QUANTITY: 1

9. CONTROL TABLES
TECHNICAL INFORMATION:
GOOD INSPECTION AND WEIGHING
QUANTITY: 3

10. PACKING MACHINE
BECK
TECHNICAL INFORMATION:
PACKING TOWELS INTO FOIL
QUANTITY: 1

3. WINDING MACHINE
SCHLAFHORST
MODEL: BKN
YEAR: 1975
TECHNICAL INFORMATION:
96 PIECES SPINDLES (2 X 48 SPINDLES)
QUANTITY: 2

4. MOBILE REGALS FOR YARN STORAGE
INCLUDED SELLING YARN
QUANTITY: 3

WARPING AND WEAVING:
1. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
HACOBA
MODEL: USK T1000/SM
YEAR: 1990
TECHNICAL INFORMATION:
ELEKTRONIC COMPUTER, AUTOMATIC SETTING OF CONE,
DEVICE FOR CROSSING THE FLOOR DIVISION THREADS
PRELIMINARY SETTING : OF LENGTH IN METERS (YARN LEGTH RECORDER), NUMBER OF REVOLUTIONS, …
CONE CREEL/CREELS 2 X 32 CROSS-WOUND COME (MAX. DIAMETER CROSS-WOUND IS 225 MM)
WETTING TROUTH FOR COLD STARCHING BY APPLICATOR ROLLER
MAXIMUM WARPING WIDTH : 240 CM/ WARPING WIDTH (MARKED) 240 CM
QUANTITY: 1

2. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
SUCKER MÜLLER HACOBA
MODEL: USK -S/SM
YEAR: 1998
TECHNICAL INFORMATION:
MAXIMUM WARPING WIDTH : 2000MM
QUANTITY: 1

3. WARPING MACHINE
BENNINGER
MODEL: 97126 FB
YEAR: 1978
TECHNICAL INFORMATION:
MAX. NUMBER OF CONES 704
QUANTITY: 1

4. SIZING MACHINE
BENNINGER ZELL
MODEL: BZ-7M
YEAR: 1975
TECHNICAL INFORMATION:
MAXIMUM WORKING WIDTH 2400MM
TOTAL BEAM 8 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
SIZING KITCHEN
QUANTITY: 1

5. SIZING MACHINE
BENNINGER ZELL
MODEL: XK Z6F
YEAR: 1986
TECHNICAL INFORMATION:
MAX. WORKING WIDTH 240 CM
TOTAL BEAM 12 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
QUANTITY: 1

13. COMPRESSOR FOR COMPRESSED AIR
KAESER
MODEL: CS 76, ABT 72
YEAR: 2003
NO. OF MASHINES: 3

14. KNOTTING MACHINE
KNOTEX
MODEL: AS/2 8013 EA03
YEAR: 2002
TECHNICAL INFORMATION:
WITH TWO TROLLEY SIZE 2500MM
QUANTITY: 5

15. ELEVATOR FOR BEAMS
GENKINGER
MODEL: EE-KHHR
YEAR: 1998
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

16. ELEVATOR FOR BEAMS
HUBTEX
MODEL: KHHW
YEAR: 1988
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

17. PUNCH MACHINE
GROSSE
MODEL: LSE 600
YEAR: 1998
TECHNICAL INFORMATION:
PUNCHING CARDS
QUANTITY: 1

18. ELEVATOR FOR BEAMS
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

19. MOBILE REGALS FOR BEAM STORAGE
TECHNICAL INFORMATION:
UP - DOWN MOVING REGALS
QUANTITY: 13

WEAVING SAURER 1;2;3;4:
1. STÄUBLI JACQUARD
WITH 560 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 10

2. STÄUBLI JACQUARD
WITH 768 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 4

3. STÄUBLI JACQUARD
WITH 1120 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

4. STÄUBLI JACQUARD
WITH 912 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MASHINES: 1

WEAVING SILK:
1. WEAVING MACHINE
SOMET
MODEL: MASTER SM93
YEAR OF CONSTRUCTION: 1990
TECHNICAL INFORMATION:
WITH STÄUBLI JACQUARD, JC4 CONTROLLER
5-6 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

2. CONTROL TABLE
TECHNICAL INFORMATION:
GOOD INSPECTION
NUMBER OF MACHINES: 1

READY MADE DEPARTMENT FOR TERRY BATHROBES:
1. CUTTING TABLE
BULLMERWERK
MODEL: KOMET II
TECHNICAL INFORMATION:
CUTTING GOODS BY CUTTING PATTERNS FOR TERRY
BATHROBES
QUANTITY: 1

2. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
QUANTITY: 2

3. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

5. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
TRIPLE STICH OVERLOK
QUANTITY: 1

6. SEWING MACHINE
LEWIS
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
BLIND STICH
QUANTITY: 1

7. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

8. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY PRODUCTS
OVERLOK
QUANTITY: 2

9. SEWING MACHINE
MAUSER SPECIAL
TECHNICAL INFORMATION:
SEWING NAPKINS
OVERLOK
QUANTITY: 1

10. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

11. SEWING MACHINE
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 1

12. SEWING MACHINE
NECCHI
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR
BONDING GOODS
QUANTITY: 4

13. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

14. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

LABOR MACHINES:
1. APPARATUS FOR MEASURING ZTWIST, TURN/ROLL - TORSIOMETER
MARK: CALDERARA BOSI
YEAR: 1989
QUANTITY: 1

2. APPARATURS FOR MEASURING THE FRICTION COEFFICIENT -
ZWEIGLE
MODEL: µ-METER G 530
TYPE: 530
YEAR: 1972
TECHNICAL INFORMATION:
NOT WORKING
QUANTITY: 1

3. LIGHTING CHAMBER

MARK: DATACOLIR INTERNATIONAL
YEAR: 2004
TECHNICAL INFORMATION:
FROM 4 TYPES OF LIGHT ONLY WORKS 1
QUANTITY: 1

4.AA WINDING APPARATURS FOR THE DYEING TUBE THE SAMPLING DEVICE
ZWEIGLE (REUTLIGEN)
QUANTITY: 1

5. WINDING APPARATURS FOR COLOR STANDARDS
IZDELANO V SVILANITU
YEAR: 2001
QUANTITY: 1

6. YARN DYEING APPARATURS PRETEMA MULTICOLOR
PRETEMA
MODEL: TYPE MC-320
YEAR: 1982
TECHNICAL INFORMATION:
V 22 W 1800
DIMENSIONS: LENGTH 119 CM X WIDTH 61 CM X HEIGHT 126 CM
INSTALLED ELECTRIC POWER: 1800 W
QUANTITY: 1

7. DYNAMOMETER FOR SPINNING
KARL SCHRÖDER
YEAR: 1977
QUANTITY: 1

8. SPEKTROFOTOMETER DATACOLOR INTERNATIONAL
DATACOLOR INTERNATIONAL
MODEL: SPECTRAFLASH SF600 PLUS CT
YEAR: 1999
TECHNICAL INFORMATION:
RATINGS: 100-240 V ̴47-63 HZ, 100 VA
NOT WORKING (DO NOT KNOW THE TYPE OF TROUBLE)
QUANTITY: 1

9. APPARATURS FOR THE VISUAL APPEARANCE OF THE YARN
ZWEIGLE KG REITLINGEN
QUANTITY: 1

QUANTITY: 1 COMPLETE PLANT

Learn More

J-3004 FIBRILLATED RAFFIA TAPE EXTRUSION LINE – NEW, 120mm PP FIBRILLATED YARN EXTRUDER LINE MODEL: NOVASTAR-120 EXTRUSION LINE FOR PRODUCTION OF PP FIBRILLATED YARN RAW MATERIAL: PP GRANULE FINISHED PRODUCTS: NON-TWISTED TAPE YARN, FIBRILLATED YARN FOR TWINE RANGE OF PRODUCT: 10,000 TO 30,000 DENIER 10000 DENIER APPROXIMATELY 17 TO 19 YARN 16000 DENIER APPROXIMATELY 11 TO 12 YARN 22000 DENIER APPROXIMATELY 8 TO 9 YARN 28000 DENIER APPROXIMATELY 6 TO 7 YARN 32000 DENIER APPROXIMATELY 5 TO 6 YARN EXTRUSION THROUGHPUT: 300 KG PER HOUR EXTRUSION CAPACITY: 180 TO 250 KG PER HOUR (PRODUCT CAPACITY DEPEND ON FILAMENT SIZE) EXTRUDER SCREW DIAMETER: Ø 120mm T-DIE WIDTH: 1300mm TAKE-OFF ROLLER WIDTH: 1200mm TAKE-OFF LINE SPEED: 160 METERS PER MINUTE (MAXIMUM) OPERATION SIDE: RIGHT TO LEFT, OR LEFT TO RIGHT Learn More

REFERENCE NUMBER: A-2481 ENTRY LEVEL SINGLE NOZZLE ELECTROSPINNING UNIT - STARTER KIT THIS ELECTROSPINNING SYSTEM IS DESIGNED FOR LOW-COST, SMALL-SCALE NANOFIBER RESEARCH, PRODUCING RESULTS FROM A SINGLE-NOZZLE CONFIGURATION IN A COMPACT UNIT. SPINNING DISTANCE, FLOW RATE AND APPLIED VOLTAGE ARE EASILY ADJUSTABLE IN SIDE-BY-SIDE SPINNING SYSTEM. SPECIFICATIONS: SPINNING-TYPE: SIDE BY SIDE SPINNING CHASSIS: ENCLOSED CHASSIS FOR SPINNING AREA COLLECTOR MATERIAL: STAINLESS STEEL TOTAL WEIGHT: APPROX.10 KGS DIMENSIONS: 210 X 170 X 190 mm HIGH VOLTAGE POWER SUPPLY VOLTAGE RANGE: 0 TO 30 KV VOLTAGE PRECISION: 0.1 KV MAX CURRENT: 0.170 MA HIGH PRECISION MICRO PUMP FLOW RATE: 0.01 TO 4464 ML/H (BD 60 ML SYRINGE) FLOW RATE PRECISION: 0.01 ML/H AVAILABLE SYRINGES STANDARD: ALL TYPES ARE AVAILABLE FEEDING AREA DIRECTLY FEED INTO NOZZLE NUMBER OF NOZZLES: 1 NOZZLE NOZZLE MATERIAL: STAINLESS STEEL COMPATIBLE WITH ALL STANDARD SYRINGE NOZZLES SPINNING DISTANCE DISTANCE BETWEEN NOZZLE AND COLLECTOR: 0 TO ∞ DISTANCE ADJUSTMENT METHOD: MANUAL DISTANCE CONTROL STATIONARY PLATE COLLECTOR MATERIAL: STAINLESS STEEL DIMENSIONS OF STATIONARY PLATE: 180 X 300 mm UNIQUE USER INTERFACE 4.3" TOUCH SCREEN CONTROL PANEL WITH WELL DESIGNED USER FRIENDLY INTERFACE FULLY ABLE TO CONTROL ALL PARAMETERS TECHNICAL REQUIREMENTS POWER: 220 VOLTS AND 50/60 HZ @ MAX 25A GROUNDING: EXTERNAL GROUNDING LINE AREA: MIN. 500 X 1000 mm WORKBENCH ABLE TO CARRY MINIMUM 8 KGS. Learn More