Search results for: 'automatic V'''

REFERENCE NUMBER: M-4863 (1111HCMTXX10) L THIES TRD-III JET DYEING MACHINE YEAR 2013 THIES TRD III JET DYEING MACHINE BOUGHT NEW IN APRIL 2013 USED APPROXIMATELY 15 TIMES 2 TUBES, BUT YOU CAN CLOSE ONE TUBE AND RUN ONE TUBE IF SMALLER BATCH IS NEEDED 150 KGS PER PORT , TOTAL FOR THE MACHINE 300 TO 330 KGS ONE STOCK TANK TWO SIDE TANKS ORGATEX SOFTWARE, YOU CAN PROGRAM THE MACHINE FROM YOUR COMPUTER AND NETWORK THE MACHINE TO THIS COMPUTER AND TRANSFER FILES FROM THE COMPUTER TO THE MACHINE AND VICE VERSA QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3010

PORTER 2000 AUTOMATIC FLANGER

 

MODEL: PFM 2000

IT INCLUDES SEWING TABLE WITH MOTOR, VACUUM SYSTEM, BOBBIN HOLDER, SEWING ARM AND FABRIC PULLING SYSTEM,NEEDLE POSITIONER

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-4566 (1111225RSJ10U) L THERMOPLASTIC HOTMELT COATING LINE MP ENGINEERING TYPE HM59-SD3 YEAR 2005 WIDTH 102” (2590mm) YEAR: 2005 TYPE: HM59-SD3 MATR: 404/04 ROLL FACE: 2600mm (102”) WORKING WIDTH: 2400mm (95”) VOLTAGE: 480/3/60 CONTROL VOLTAGE: 110/60 CONSISTING OF: CAROUSEL 3 POSITION LET-OFF, ENTRY ON ACCUMULATOR WITH HOT-WIRE SEAMING DEVICE, 8000 VOLT STATIC ELIMINATOR, PNEUMATICALLY OPERATED FABRIC HOLDING DEVICE FOR TENSION CONTROL, ACCUMULATOR WITH 8-ROLLS UP AND 9-ROLLS DOWN APPROX.. 80-YARD CAPACITY, COMPENSATING ARM ON EXIT SIDE. ROLLS ARE 4” DIA. X 102” FACE ALUMINUM, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. SECOND ACCUMULATOR WITH ROLL CRADLE FOR SECOND SUBSTRATE LET-OFF, ACCUMULATOR WITH 9-ROLLS UP AND 10 ROLLS DOWN, APPROX.. 54 YARD CAPACITY, ROLLS ARE 4’ DIA. X 102” FACE ALUMINUM, INCLUDES 8000 VOLT STATIC ELIMINATOR AND PNEUMATIC FABRIC HOLDING FOR TENSION, PENDULUM TYPE GUIDING DEVICE ON EXIT SIDE, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. OVERHEAD GANTRY WITH ACCESS STAIRS ON RIGHT SIDE OF FIRST ACCUMULATOR, EXTENDS OVER THE EXTRUDER WITH JIB MOUNTED FOR EASE IN REMOVING DIE FROM MACHINE, GUIDING/CENTERING DEVICE MOUNTED ONTO GANTRY FEEDING COATING HEAD. MP ENGINEERING EXTRUDER/APPLICATOR TYPE HM59-SD3, MATR. NO. 402/04, WITH 102” DIE, 98” RUBBER-BELT WITH PNEUMATIC CYLINDERS FOR BELT TENSION AND GUIDING, HEATED CYLINDER BACKING TO DIE, OPERATOR PLATFORM, CONTROLS MOUTNED IN DOOR AND OPERATOR TOUCH SCREEN PANEL. (NOTE: THESE ARE PRESENTLY MOUNTED ON PRODUCTION LINE AND WILL BE REMOVED AND PLACED BACK INTO/ONTO APPLICATOR. 480/3/60 COATEM SISTEMI C.R.L. IMBALLAGIO & HOT MELT EXTRUDER, S/N 50701, TYPE/MODEL CE-200, WITH DIGITAL MICROPROCESSOR AND INVERTER FOR SPEED VARIATION, DESIGNED TO WORK MAINLY WITH POLYESTER, POLYAMIDE AND POLYURETHANE BUT CAN ALSO EXTRUDE ABS, POLYTHENE, POLYPROPYLENE AND ADHESIVES LIKE EVA ADHESIVES. 480/3/60 CONAIR DRYER CD-300, PL-D-196-1, MODEL D03H4101310, S/N 9D0597, 480/3/60, AND HOPPER. THIRD ACCUMULATOR FOR BONDED PRODUCT WITH 6-ROLLS UP AND 7-ROLLS DOWN, APPROX…60-YARD CAPACITY, ROLLS ARE 6” DIA. X 102” FACE ALUMINUM, WITH DRAW-ROLL TENSION DEVICE MOUNTED ONTO EXIT, OVERHEAD CARRIER ROLLS AND FRAMEWORK DELIVERY TO ELECTRIC A-FRAME WINDER WITH 102” FACE LAY-ON ROLL, AND SEMI-AUTOMATIC BATCHER FOR INDIVIDUAL ROLLS, 2-ROLL SURFACE WINDING 102” FACE WIDTH, OVERHEAD CORE FEED, FABRIC CENTERING DEVICE, ELECTRIC SCISSOR CUT-OFF, KICK-OUT TO 2-ROLL BED, OPERATOR PLATFORM AND OPERATOR CONTROLS. ALL MACHINES PRODUCED BY MP CONFORMS TO EEC DIRECTORY 89/392 CEE (CE MARK) TECHNICAL FEATURES OF THE LINE, ACCORDING TO DWG 100-904/1C ROLLERS WIDTH 2600mm WORKING WIDTH 2400mm MAXIMUM DIAMTER OF THE ROLLS OF PU FOAM 1500mm MAXIMUM DIAMETER OF THE UNWOUND ROLLS OF FABRIC 600 ° 1500 MAXIMUM DIAMETER OF THE REWOUND ROLLS 500 ° 1500 (IN CASE YOU ARE REWINDING ROLLS OF FABRIC LAMINATED TO PU FOAM, THE MAXIMUM DIAMETER IS 1750mm) ADJUSTABLE MECHANIC SPEED: 5 TO 50 M/MIN MAIN POWER SUPPLY + NEUTRAL + EARTH 480+N+E/60 V/HZ VOLTAGE ON CONTROL PANELS 110/60 V/HZ INSTALLED POWER FOR MOTORS 22KW INSTALLED POWER FOR IR HEATER 14,25KW INSTALLED POWER TO HEAT THE SLOT-DIE 32KW INSTALLED POWER FOR THE THERMAL OIL HEATING UNIT FOR THE CALENDERING ROLLERS 32,2KW INSTALLED POWER FOR THE CHILLER 12,9KW A.C. MOTORS, DRIVER, ELECTRIC CABLES ARE ACCORDING TO CEI NORMS BACKGEAR ROLLERS, WITH PAINTED SURFACE OR ALUMINUM MADE WITH DIAMETER 100/120/150mm COMPRESSED AIR CONSUMPTION, AT 6 BAR 1500LT/H COOLING WATER CONSUMPTION (WATER MUST HAVE A TEMPERATURE NOT HIGHER THAN 10°C) 5500LT/H ADJUSTABLE TENSION ON THE REWOUND MATERIALS 5 A 35 KG. PAINTING GREEN RAL 6027 E BLUE MARINE RAL 5021 A.C. MOTORS CONTROL THE SPEED OF THE MACHINES, AND ARE AUTOMATICALLY SYNCHRONISED THROUGH ELECTRONIC DRIVES (INVERTER) AND PNEUMATIC DANCER UNITS (COMPENSTAORS) ESTRUDER: CAPACITY UP TO 200 KG/H (DEPENDING ON THE VISCOSITY OF THE ADHESIVE TO BE EXTRUDED) POWER OF THE MOTOR AND RESISTANCES: 90KW MAXIMUM MELTING TEMPERATURE: 220°C MATERIALS TO BE PROCESSED NONWOVENS 30:150 GR/M2 SYNTHETIC AND NATURAL FABRICS (EXCLUDING STRETCHY FABRICS) WITH WEIGHT 100:600 GR/M2 SCRIMS FOR BACKING FABRIC WITH WEIGHT 70:120 G/M2 MAXIMUM THICKNESS OF PU FOAM 15mm MINIMUM THICKNESS OF PU FOAM 2mm DENSITY OF PU FOAM 22/40 KG/M3 THERMOPLASTIC ADHESIVE TO BE COATED THERMOPLASTIC HOTMELTS (COPOLYAMMIDE, COPOLYESTER, EVA AND POLYURETHANE THERMOPLASTIC HOTMELT GRANULES) DATA REFERRING TO PRODUCTION THE PRODUCTION SPEED CAN CHANGE, DEPENDING ON THE KIND OF HOTMELTS, ON THEIR MELTING TEMPERATURE, ON THEIR VISCOSITY, AND ON THE GRAMS PER SQUARED METER TO BE COATED QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: A-1115 BRAZZOLI H.T. DYEING MACHINES TERRY TOWEL YEAR 2002 Brazzoli H.T. Dyeing machines, for terry towel fabrics. Type Saturno Luft HTF. Year 2002 Capacity 400kg each machine, these machines can also be operated coupled to dye one lot of 800kg. Supplied with main motor and pump, automatic valves for steam and water functions. Add tank + dosing pump. Electrical panel with Microprocessor controls. QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4787 (1111BGJWXX10) L BLACK CLAWSON EXTRUSION COATER LAMINATOR YEAR 1992 WEB WIDTH 1575mm BLACK CLAWSON EXTRUSION COATER LAMINATOR YEAR 1992 WEB WIDTH 1575mm (62 INCHES) L/D(S): 30:1 DRIVE SYSTEM: 250HP DC DRIVE SPEED: 305 MPM (1000 FPM) EXTRUDER(S): BLACK CLAWSON PRIME COATER: NONE SIZE(S): 4-1/2” PRIMARY UNWIND: NONE SECONDARY UNWIND: NONE REWIND: NONE DRYER TYPE: NONE EQUIPPED WITH MODEL 111 EXTRUSION COATER WITH 30” DIAMETER X 72” FACE CHILL ROLL PRESSURE ROLL ASSEMBLY WITH 12” DIAMETER, 6” DIAMETER NIP ROLL AND LEAD-IN SPREADER ROLL 11” DIAMETER SECONDARY CHILL ROLL; SLITTING STATION MODEL 400 EXTRUDER MOUNTED ON XYZ CARRIAGE WITH 250HP DC MOTOR 4-1/2” DIAMETER SCREW IS ELECTRICALLY HEATED AND WATER COOLED; VALVED ADAPTER 72” CLOEREN AUTOMATIC DYE WITH EDGE BEAD REDUCTION AND EXHAUST HOOD QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-9758 PICANOL OPTIMAX LOOMS YEAR 2007 WIDTH 2200mm PICANOL LOOMS MODEL: OPTIMAX 4 - R 220 WIDTH: 2200mm YEAR: 2007 4 COLORS STAUBLI DOBBY TYPE 2861 WITH 14 SHAFTS INSTALLED ACCESSORIES ON EACH LOOM: (16) HEALD FRAMES (4) WEFT-ACCUMULATORS IRO LUNA (1) WARP-BEAM DIAMETER 1000mm BATCHING MOTION WITH AUTOMATIC INSPECTION SYSTEM ELECTRONIC TAKE-UP 6,000 HEDDLES 6,000 DROPPERS 650 RPM 380 VOLTS, 50 HZ RUNNING DENIM FABRICS QUANTITY AVAILABLE: 12 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

BENNINGER ZELL HIGH PERFORMANCE SIZING MACHINE, 1995 TYPE: BEN – SIZETEC SWA TKD 2T8 BB USABLE WIDTH: 2200mm MACHINE TYPE: BEAM TO BEAM SINGLE SIZE BOX CONSISTING OF DOUBLE DIP, DOUBLE NIP ROLLERS WET SPLITTING ZONE 8 DRYING CYLINDERS WAXING DEVICE SIZE KITCHEN WITH COOKER TYPE SHEARTRONIC 700, CAPACITY 700 LITRES, SIZE STORAGE TANK TYPE V10T, CAPACITY 1000 LITRES AUTOMATIC DELIVERY SYSTEM TO SIZE BOX UPGRADED WITH HMI SYSTEM TOUCH SCREEN IN 2011 Learn More

REFERENCE NUMBER: K-9834 GIUDICI RG-30TA AIR TEXTURIZER YEAR 1998 - 24 POSITIONS CAN PROCESS FDY, POY, ETC. AIR TEXTURIZER MANUFACTURER: GIUDICI ITALY MODEL: RG-30TA YEAR: 1998 INSTALLED IN 1999 WITH VERY LOW WORKING HOURS 24 POSITIONS SPEED UP TO 1,000 METERS PER MINUTE FOR SINGLE, PARALLEL, CORE EFFECT YARNS FOR POY OR FDY YARNS FOR POLYESTER, NYLON, OR POLYPROPYLENE FOR DENIERS 150 UP TO 3,000 WITH APPROPRIATE JETS HEAVY DUTY CREEL FOR UP TO 80 RUNNING ENDS SUPPLY PACKAGES UP TO 30 POUNDS PNEUMATIC THREADING YARN CUTTERS FOR ONE AND TWO ENDS ELECTRONIC YARN SENSORS ON THE CREEL FIRST SET OF HEATED GODETS 105mmɸ WITH SEPARATOR ROLLS SECOND SET OF HEATED GODETS 105mmɸ WITH SEPARATOR ROLLS STAINLESS STELL AIR JET BOX SOUND PROOF AND WATER PROOF WITH PLEXIGLASS COVERS WETTING NOZZLES 24 NEW JETS BY INTERNATIONAL MACHINERY SALES IMF WATER SUPPLY PIPING AND INDIVIDUAL SOLENOID VALVES WATER AND SPRAY EXHAUST SYSTEM THIRD GODET HEATED TO CONTROL SHRINKAGE AND OVERFEED TAKE UP YARN OILING SYSTEM BY KISS ROLL TAKE UP PACKAGE 250mm TRAVERSE BY 290mm DIAMETER INDIVUDAL AUTOMATIC DOFFING SYSTEM COMPUTERIZED CONTROLS TO OVERSEE: -MACHINE AND SHAFT SPEED -DRAW RATIOS INFINITELY -TAKE UP SPEED -TRAVERSE SPEED AND RIBBON BREAKING -WINDING ANGLE -WEIGHT OF EACH INDIVIDUAL TAKE UP PACKAGE -TEMPERATURE OF EACH GODET -ELECTRONIC YARN SENSORS STATUS MACHINE DIMENSIONS: LENGTH 7880mm, WIDTH 5305mm, HEIGHT 3350mm ELECTRICAL: 480/380/3/60-50 KW TOTAL DRIVE: 50.25 KW HEATING: 50.25 IN EXCELLENT CONDITION MACHINE WILL BE RECONDITIONED AND TESTED QUANTITY AVAILABLE: 1 Learn More