T-8260 ALBRECHT BAUMER IS-M, 40 METERS PER MINUTE, CUT HEIGHT 1300mm, YEAR 1987

REFERENCE NUMBER: T-8260 ALBRECHT BAUMER IS-M, 40 METERS PER MINUTE, CUT HEIGHT 1300mm, YEAR 1987 MAKE: ALBRECHT BAUMER MODEL: IS-M SPEED: 0 TO 40 METERS PER MINUTE CUTTING HEIGHT: 1300mm KNIFE MEASUREMENTS: 10 x 0.45 x 10350mm POWER SUPPLY: 380 VOLTS, 3-PHASE, 50 Hz POWER REQUIREMENT: 4 KW YEAR: 1987 RIGHT TABLE: 2435mm BUN WIDTH (RIGHT TABLE): 2200mm BUN LENGTH: 2580mm LEFT TABLE: 2435mm BUN WIDTH (LEFT TABLE): 2200mm BUN LENGTH: 2580mm) INCLUDES: • OPERATIONS MANUAL • SPARE PARTS CATALOGUE • DRAWINGS • SPARE PARTS NUMBERS • ELECTRICAL DIAGRAM • THREE EXTRA CUTTING BLADES • PROTECTIVE GRILLS CAN BE PROGRAMMED TO CUT AUTOMATICALLY AND THE PROGRAMS CAN BE STORED FOR FUTURE USE. MACHINE CAN CUT IN BOTH DIRECTIONS (KNIFE CUTS FORWARDS AND BACKWARDS) EQUIPPED WITH GRINDING DISKS FOR SHARPENING THE BLADE WORKING TABLE SHEETS ARE MADE OF ANODIZED ALUMINUM FOR EASY DISPLACEMENT OF THE FOAM BLOCKS WORKING TABLE CAN BE EXTENDED WITH 750mm BY TURNING DOWN THE SIDE SUPPORT IN GOOD CONDITION INFORMATION BELOW IS FROM ALBRECHT BAUMER’S WEBSITE, SPECIFIC TO THIS MODEL: MATERIAL: BLOCK AND SHEET WARE FROM PUR SOFT FOAM, NONWOVEN MATERIAL, RUBBER FOAM, LATEX, EPDM FOAM AND BASOTECT, ROCK WOOL AND GLASS WOOL AS WELL AS PUR RIGID FOAM, EPP CUTTING BLADE: PRECISION-GROUND CIRCULATING GROUND KNIFE WITH WIDTH OF 6 TO 20mm, AVAILABLE EITHER AS TOOTHED KNIFE OR AS SET KNIFE MOTOR-DRIVEN UPPER KNIFE PROTECTION UNIT MOTOR-DRIVEN GRINDING UNIT RIGHT SIDE STOP WORKING TABLE WITH ANODIZED ALUMINUM SURFACE PNEUMATIC KNIFE TENSIONING SUPPORT THE MACHINE IS IN GOOD CONDITION AND READY TO CUT IS-M VERTICAL CUTTING MACHINE: VERY HIGH CUTTING PRECISION FOR HIGHEST CUTTING STANDARDS SECOND TILTABLE LEFT SIDE STOP FOR EASY LOADING OF THE MACHINE UTILIZATION OF THE LEFT TABLE HALF AS TURNTABLE FOR PRECION RECTANGLE CUTS UTILIZATION OF A FREQUENCY-CONTROLLED KNIFE DRIVE FOR THE CUTTING OF SPECIAL FOAMS AIR CUSHION SYSTEMS FOR AN EFFORTLESS HANDLING OF LARGE BLOCKS MATERIAL FIXING BY AN OPTIONAL HOLDING DOWN SYSTEM MINIMAL SPACE REQUIREMENT DUE TO A STATIONARY TABLE AND A MOVABLE CUTTING UNIT MINIMIZATION OF CUTTING TIMES AS IT IT POSSIBLE TO CUT IN BOTH DIRECTIONS - EMPLOYMENT OF A KNIFE TWISTED BY 180° POSSIBILITY OF A CUSTOMIZED AND CUSTOM-DESIGNED DESIGN DUE TO A NUMBER OF DIFFERENTLY CONFIGURABLE TABLE DIMENSIONS OF BOTH TABLE HALVES. SPECIAL DESIGN WITH SET KNIFE FOR THE CUTTING OF INSULATING MATERIAL (E.G. MINERAL WOOL, PUR RIGID FOAM OR POLYSTYRENE (EPS)) KEY FACTS: APPLICATION MATTRESSES, FURNITURE, PACKAGING AND AUTOMOTIVE INDUSTRY, CONSUMER GOODS/HOUSEHOLD GOODS INDUSTRY, SPECIAL APPLICATIONS SUCH AS CERAMIC FILTERS (RETICULATED FOAMS), VERTICAL CUTTING MATERIAL BLOCK AND SHEET WARE FROM PUR SOFT FOAM, NON-WOVEN MATERIAL, RUBBER FOAM, LATEX, EPDM FOAM AND BASOTECT®, ROCK WOOL AND GLASS WOOL AS WELL AS PUR RIGID FOAM, EPP CUTTING TOOL PRECISION-GROUND CIRCULATING GROUND KNIFE WITH WIDTHS OF 6-20 MM, AVAILABLE EITHER AS TOOTHED KNIFE OR AS SET KNIFE TECHNICAL DATA: STANDARD MOTOR-DRIVEN UPPER KNIFE PROTECTION UNIT MOTOR-DRIVEN GRINDING UNIT RIGHT SIDE STOP WORKING TABLE WITH ANODIZED ALUMINIUM SURFACE PNEUMATIC KNIFE TENSIONING SUPPORT OPTIONS AIR CUSHION SYSTEM CONTINUOUSLY ADJUSTABLE KNIFE SPEED COOLING UNIT GRINDING DUST EXTRACTION UNIT HOLDING DOWN DEVICE INCREASE OF SIDE STOP FROM 750mm TO 1000mm LEFT SIDE STOP LEFT WORKING TABLE AS TURNTABLE OPTICAL KNIFE GRINDING CONTROL VERSION WITH ANGLE-TOOTHED KNIFE VERSION WITH SET KNIFE • SPECIAL DESIGN WITH SET KNIFE FOR THE CUTTING OF INSULATING MATERIAL SUCH AS EPP AND ROCK WOOL LEFT WORKING TABLE AS TURNTABLE • EASY, EFFICIENT AND PRECISE CUTTING OF RECTANGULAR PARTS WITHOUT MANUAL TURNING OF THE MATERIAL • FOR EXAMPLE FOR THE CUTTING OF ADHESIVE LAMINATED GOODS AIR CUSHION SYSTEM • AIR CUSHION GENERATED BY A FAN • LEFT AND RIGHT WORKING TABLE CAN BE EQUIPPED WITH AN AIR CUSHION • RECOMMENDED FOR MULTIPLE TURNING OF THE BLOCK DURING TRIMMING • VERY EASY MOVING OF THE BLOCK ON THE TABLE HOLDING DOWN DEVICE • HOLDING DOWN DEVICE IN CONNECTION WITH TURNTABLE • ACHIEVEMENT OF MINIMAL CUTTING TOLERANCES OPTICAL KNIFE GRINDING CONTROL • BETTER CONTROL OF THE KNIFE GRINDING AT BOTH BEVELS DUE TO A MICROSCOPE MEASURING MAGNIFYING GLASS WITH ILLUMINATION • OPTIMUM CUTTING RESULTS AND TOLERANCES. QUANTITY: 1