TT-1355 SPRAY DRYER, CAPACITY OF EVAPORATION 50L/H

REFERENCE NUMBER: TT-1355 SPRAY DRYER, CAPACITY OF EVAPORATION 50L/H SPRAY DRYER CAPACITY OF EVAPORATION: 50L/H ELECTRICAL HEATING, 3 PHASE 380V 50Hz DESIGN BASIS 1. DRY PRODUCT: ORIGINAL MOISTURE CONTENT 60-90% 2. INLET AIR TEMPERATURE: ADJUSTABLE FROM 100°C TO 200°C 3. AIR OUTLET TEMPERATURE: 80C-90C (ADJUSTABLE ACCORDING TO THE MOISTURE CONTENT OF THE FINISHED PRODUCT) 4. MAXIMUM WATER EVAPORATION: 50 ^/H (RELATED TO SPECIFIC MATERIAL CHARACTERISTICS) 5. PRODUCT PARTICLE SIZE: 80-200 MESH (VARIES ACCORDING TO DIFFERENT RAW MATERIALS) EQUIPMENT CHARACTERISTICS AND METHODS 1. ATOMIZATION METHOD: HIGH-SPEED CENTRIFUGAL ATOMIZATION. 2. FEEDING SYSTEM: FEEDING PUMP FEEDS. (FREQUENCY) 3. RECEIVING METHOD: COLLECT FROM THE BOTTOM OF THE TOWER TO THE NEXT POINT OF THE CYCLONE SEPARATOR. 4. HEATING METHOD: ELECTRIC HEATING. 5. TOTAL EQUIPMENT POWER: 72KW PROCESS EXPLANATION THE TREATED FEED LIQUID IS PUMPED FROM THE FEED TO THE CENTRIFUGAL ATOMIZER AT THE TOP OF THE DRYING TOWER. THE ROTATIONAL SPEED OF THE CENTRIFUGAL ATOMIZER IS 18500R.P.M. UNDER THE ACTION OF CENTRIFUGAL FORCE, THE FEED LIQUID IS ATOMIZED UNIFORMLY AND ENTERS THE TOWER. AFTER THE NORMAL TEMPERATURE AIR IS TREATED BY THE HIGH-EFFICIENCY AIR FILTER, IT ENTERS THE HEATING SYSTEM. WHEN IT IS HEATED TO THE TEMPERATURE REQUIRED BY THE PROCESS, IT ENTERS THE UPPER PART OF THE DRYING TOWER EVENLY THROUGH THE HOT AIR PIPELINE AND HOT AIR DISTRIBUTOR. DRY TO POWDER. THE DRIED POWDER IS SEPARATED FROM THE CYCLONE SEPARATOR THROUGH THE DISCHARGE PIPELINE AT THE BOTTOM OF THE DRYING TOWER, AND THE SEPARATED POWDER IS COLLECTED BY THE BOTTOM BUCKET; THE DUST AND EXHAUST GAS SEPARATED BY THE CYCLONE SEPARATOR ARE THEN INTRODUCED INTO THE WET DUST COLLECTOR THROUGH THE INDUCED DRAFT FAN, AND AFTER DUST REMOVAL TREATMENT EXHAUST INTO THE ATMOSPHERE. DEVICE CONFIGURATION FEEDING SYSTEM: ITEM 001 PERISTALTIC PUMP QUANTITY: 1 SET ITEM 002 FEED PIPE QUANTITY: 1 SET INDUCTION SYSTEM: ITEM 003 INDUCED DRAFT FAN QUANTITY: 1 SET ITEM 004 HOT AIR INSULATION PIPELINE INNER 5=2mm, OUTER 5=1.5mm 304 STAINLESS STEEL INSIDE AND OUTSIDE, ROCK WOOL INSULATION 5=80mm QUANTITY: 1 SET ITEM 005 EXHAUST DUCT 304 STAINLESS STEEL QUANTITY: 1 SET ITEM 006 PIPE CONNECTORS FLANGE 304 STAINLESS STEEL QUANTITY: 1 SET HEATING SYSTEM: ITEM 007 AIR FILTRATION STANDARD CABINET ASSEMBLY QUANTITY: 1 SET ITEM 008 ELECTRIC HEATING ZHENGTAI STAINLESS STEEL ASSEMBLY QUANTITY: 1 SET DRYING HOST AND MATERIAL COLLECTION SYSTEM: ITEM 010 SPRAY DRYING CHAMBER THE INNER DIAMETER IS 2000mm, THE OUTER DIAMETER IS 2150mm, THE INNER AND OUTER WALLS ARE MADE OF 304 STAINLESS STEEL, THE INNER WALL THICKNESS IS 2mm OUTER WALL THICKNESS 1.2mm, WIRE DRAWING QUANTITY: 1 SET ITEM 011 INLET VOLUTE STAINLESS STEEL QUANTITY: 1 SET ITEM 012 HOT AIR DISTRIBUTOR STAINLESS STEEL QUANTITY: 1 SET ITEM 013 CENTRIFUGAL NEBULIZER STAINLESS STEEL /FREQUENCY CONVERSION ADJUSTMENT, MAXIMUM SPEED 18500RPM QUANTITY: 1 SET ITEM 014 OBSERVE THE ACTUAL 00mm ASSEMBLY QUANTITY: 1 SET ITEM 015 OBSERVATION MANHOLE 420X500 304 STAINLESS STEEL QUANTITY: 1 SET ITEM 016 KEEP WARM THICKNESS 50mm ROCK WOOL QUANTITY: 1 SET ITEM 017 CYCLONE SEPARATOR 5=2mm 304 STAINLESS STEEL QUANTITY: 2 SET ITEM 018 UNLOADING BARREL 304 STAINLESS STEEL QUANTITY: 2 SET ITEM 019 AIR HAMMER ASSEMBLY QUANTITY: 2 SET ITEM 020 OPERATING PLATFORM FENCE CARBON STEEL QUANTITY: 1 SET ITEM 021 LADDER CARBON STEEL QUANTITY: 1 SET ITEM 022 MAIN TOWER LEGS CARBON STEEL QUANTITY: 1 SET CONTROL SYSTEM: ITEM 023 CONTROL CABINET PLC CONTROL, SEVEN-INCH TOUCH SCREEN SURFACE SPRAY QUANTITY: 1 SET ITEM 024 BREAKER ASSEMBLY QUANTITY: 1 SET ITEM 025 INTERMEDIATE RELAY ASSEMBLY QUANTITY: 1 SET ITEM 026 ATOMIZER INVERTER ASSEMBLY QUANTITY: 1 SET ITEM 027 CONNECT THE WIRES ASSEMBLY QUANTITY: 1 SET ITEM 028 EMERGENCY BUTTON ASSEMBLY QUANTITY: 1 SET ITEM 029 TERMINALS ASSEMBLY QUANTITY: 1 SET