Search results for: 'Process+of+clea'

M-6053 SPUNBOND PRODUCTION LINE, WORKING WIDTH 4040mm TO 4500mm

OFFER 001
SPUNBOND PRODUCTION LINE
WORKING WIDTH: 4040mm
WEIGHT: 130 TO 250 G/M2

OFFER 002
POLYMER CLEANING GROUP

OFFER 003
CRYSTALLIZING GROUP

OFFER 004
DRYING GROUP

OFFER 005
PNEUMATIC CONVEYING SYSTEM

OFFER 006
EXTRUDER HOPPER

OFFER 007
EXTRUDER

OFFER 008
FILTERING UNIT

OFFER 009
MELT TRANSFER LINE

OFFER 010
SPINNING BEAM

OFFER 011
SPINNING PACKS

OFFER 012
FILAMENTS QUENCHING SYSTEM

OFFER 013
FILAMENTS DRAWING AND DISTRIBUTION SYSTEM

OFFER 014
WEB FORMING CONVEYOR BELT

OFFER 015
CREEL FOR APPLICATION OF REINFORCING FILAMENTS

OFFER 016
PRE-NEEDLING MACHINE

OFFER 017
NEEDLING MACHINE

OFFER 018
THERMOSETTING UNIT

OFFER 019
OUTLET CALENDER

OFFER 020
FOULARD

OFFER 021
BINDER PREPARATION SYSTEM

OFFER 022
DRYER

OFFER 023
OUTLET CALENDER

OFFER 024
AUTOMATIC WINDER

OFFER 025
AIR COMPRESSORS (FOR FILAMENTS STRETCHING EJECTORS)

OFFER 026
DIATHERMIC OIL HEATING SYSTEM

OFFER 027
CHILLED WATER CIRCULATION AND GENERATION SYSTEM

OFFER 028
EQUIPMENT FOR CLEANING CYCLE, SPECIAL TOOLS

OFFER 029
FIBRE DUST RECOVERY SYSTEM

OFFER 030
EDGES RECOVERY SYSTEM

OFFER 031
SPINNING SECTION STEEL STRUCTURE

OFFER 032
DISTRIBUTION ELECTRIC CABINETS

OFFER 033
PROCESS ELECTRIC SYSTEM OF EXISTING MACHINES ACCORDING TO THE ACTUAL LAYOUT

OFFER 034
CABLES AND CABLING MATERIALS

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: A-2510 NANOSPIDER - ELECTROSPIN FIRST – (ROUNDED TANKS) NEW GENERATION NS PRODUCTION LINE ALLOWS NANOFIBERS TO BE PRODUCED ON A FULLY-INDUSTRIAL SCALE FOR A NUMBER OF APPLICATIONS FEATURES: • CONSTRUCTION USING SELF - EXTINGUISHING MATERIALS • VENTILATED SPINNING CHAMBER, PREVENTING THE ESCAPE OF SOLVENT FUMES • GROUNDING ROD FOR CHARGE DISSIPATION AND AUTOMATIC GROUNDING SYSTEM • FOUR EMERGENCY - STOP BUTTONS ARE PLACED ON THE CORNERS OF THE UNIT • ONE EMERGENCY - STOP BUTTON IS PLACED ON THE SERVICE CONTROL PANEL • THE TWO UPWARD SLIDING DOORS ARE EQUIPPED WITH AUTOMATIC DOOR LOCKS WITH LIMIT SWITCHES TO PREVENT ACCIDENTAL OPENING AND WILL ALSO SHUT DOWN THE UNIT IF A SLIDING DOOR IS ACCIDENTALLY OPENED • THE FOUR LOWER SWING OPEN DOORS HAVE LIMIT SWITCHES THAT WILL SHUT DOWN THE UNIT IF THE DOOR IS ACCIDENTALLY OPENED • FIRE SUPPRESSION SYSTEM FOR THE SPINNING CHAMBER WITH MANUAL ACTIVATION VIA BUTTON ON THE CONTROL PANELS • THE EQUIPMENT IS PRODUCED ACCORDING TO CE STANDARDS • RECOMMENDED ROOM LAYOUT: THE LAYOUT WILL BE OPTIMIZED ACCORDING TO BUYER NEEDS • LIGHTS ON THE FRONT AND BACK OF MACHINE SPECIFICATIONS: POLYMER (PROCESS) TANKS COMPONENT IS CONSISTING FROM FOLLOWING PARTS • CYLINDRICAL TANKS ON WHEELS, ONE FOR FRESH POLYMER • CYLINDRICAL TANKS ON WHEELS, ONE FOR WASTE • MIXING CAPABILITY (PNEUMATIC MIXTURE) FOR IN AND OUT TANKS - PNEUMATIC DRIVEN AGITATOR • CLEANING SHOWER FOR BOTH IN AND OUT TANK • TWO CYLINDRICAL SHAPED TANKS ON THE WHEELS IN ONE TUB • BURST DISK FOR EACH TANK • QUICK COUPLINGS STÄUBLI HCB 08 WORKING VOLUME OF TANKS IS 60 LITERS FOR EACH TANK CLEANING TANKS COMPONENT IS CONSISTING FROM FOLLOWING PARTS • TANK WITH VOLUME OF 60 LITERS WILL BE DIVIDED INTO TWO SECTIONS: 30 L FOR CLEAN,30 L USED CLEANING SOLUTION • CYLINDRICAL TANK ON WHEELS - SIZE ROUGHLY HALF OF THE PROCESS TANKS • BURST DISK FOR EACH TANK VOLUME 30 + 30 LITERS WILL BE POSSIBLE TO USE MULTIPLE TIMES FOR CLEANING SITE PREPARATION / CONNECTION REQUIREMENTS ALL POWER SUPPLY IS REALIZED FOR FULL LINE INCLUDING PERIPHERAL PARTS. IT IS JUST NECESSARY TO CALCULATE INCREASE OF ELECTRICAL POWER, SPACE AND AIR FLOW VOLTAGE: 220 VOLTZ AND 50/60Hz, MAIN CIRCUIT BREAKER 32 A POWER CONSUMPTION: UP TO 12 KW PRESSURE AIR: 5 TO 8 BAR, CONNECTION POINT CAPACITY 1000 L/min INERT GAS: 0.5 BAR, CONNECTION POINT CAPACITY 200 L/min PROCESS AIR INLET/OUTLET: UP TO 1000 M3/H PRODUCT SIZE AND WEIGHT LENGTH: APPROX. 2800 mm WIDTH: APPROX. 3300 mm HEIGHT: APPROX. 3000 mm WEIGHT: APPROX. 2500 KG SCOPE OF SUPPLY SPINNING CHAMBER • WITH WIRE COLLECTING ELECTRODE • LIFTING MECHANISM OF CART CAPABLE OF ADJUSTING THE DISTANCE BETWEEN THE COLLECTING AND SPINNING ELECTRODE BETWEEN 150 AND 250 mm VIA THE CONTROL PANEL • HV PROTECTING COVERS • SLIDING DOORS WITH ILLUMINATION • AIR INLET AND OUTLET WITH HOMOGENIZER AND FANS EXTINGUISHING SYSTEM • SWITCHBOARD SPINNING CART • 2 X PROCESS DOUBLE - TANKS (ONE CART ON WHEEL, EACH WITH IN AND OUT TANK) • CDS – CHEMICAL DISTRIBUTION SYSTEM • SEPARATE SPINNING MODULE EACH WITH MOVABLE CARRIAGE WITH SPINNING HEAD, ENERGY CHAIN • HV COVERS • WIRE SPINNING MECHANISM • WIRE ALIGNMENT MECHANISM • SET OF WIRE SPOOL 0.2 mm AND 0.3 mm MAIN OPERATOR PANEL – CONTROL SYSTEM HV POWER SUPPLIES SYSTEM (MAXIMUM AVAILABLE RATINGS + 80 KV DC / - 60 KV DC) SET OF SPINNING NOTCHES – FOR ROR 1 X CLEANING TANKS SERVICE OPERATION PANEL AUTOMATIC DISCHARGER R & D MODE ENABLE ELECTRO SPINNING FROM 4 WIRES ONLY – ONE MODULE PREPARATION FOR DRIVEN ENDLESS BELT COLLECTING ELECTRODE NOT IN SCOPE OF SUPPLY • SPARE WIRE FOR SPINNING • SPARE POLYMER CONTACT COMPONENT: CDS (PUMPS, VALVES, HOSES), SPINNING CARRIAGES WITH SPINNING HEADS, ENERGY CHAINS WITH POLYMER HOSES • SET OF SPINNING NOTCHES – NOT NECESSARY FOR ROR • ENDLESS BELT COLLECTING ELECTRODE REWINDING 1600 mm FULL THE NS LINE ALLOWS THE PRODUCTION OF NANOFIBERS ON A SUBSTRATE MATERIAL ONLY. THE SUBSTRATE MATERIAL MUST BE PRESENT IN THE SPINNING UNIT DURING THE SPINNING PROCESS. MOST NANOFIBER PRODUCTS USE TEXTILE, PAPER, OR FOIL SHEETS IN ROLLS AS A SUBSTRATE MATERIAL. UNWIND AND REWIND EQUIPMENT ALLOWS BIDIRECTIONAL REWINDING OF THE SUBSTRATE MATERIAL. THE ROLL GOODS EXCHANGE AND INSERTION IS MANUAL. MANIPULATION TOOLS ARE USUALLY NECESSARY BOTH UNWIND AND REWIND CONTAINS STEEL FRAMES WITH MOTORS, WHICH DRIVE THE UNWINDING AND WINDING PNEUMATIC SHAFTS SPEED IS CONTROLLED BY A SPECIAL RUBBER CYLINDER. THE PNEUMATIC SHAFTS ARE INFLATABLE AND SUITABLE FOR USE WITH PAPER CORES FEATURES: MAIN ROLL UNWINDER • THE SIDE-WALLS OF UNWINDER ARE CONNECTED BY WELDED CROSS-BEAMS WHICH ENSURE RELATIVE POSITION OF THE SIDE-WALLS AND STABILITY OF THE MACHINE. THE BEAMS CAN ALSO BE USED TO HANDLE THIS PART OF THE MACHINE. THERE ARE MACHINED MOUNTING AREAS ON INNER SURFACES OF THE SIDE-WALLS FOR THE WINDING SHAFT SAFETY CHUCKS, WINDING SHAFT DRIVE AND BEARING BODIES OF THE BALANCED STAINLESS STEEL FREE-RUNNING ROLLERS. THE SURFACES OF THE STAINLESS STEEL FREE RUNNING ROLLERS ARE MACHINED • THE UNWINDER IS EQUIPPED SWINGING SPLICING TABLE. MAT SPLICING IS SOLVED BY THE CUSTOMER (E.G. DOUBLE STICKY TAPE) • THE POSITION OF THE DANCER IS MONITORED IN CONTACTLESS MANNER BY MEANS OF A CAM AND AN ANALOGUE SENSOR. INFORMATION FROM DANCER SERVES FOR THE RIGHT FUNCTION OF THE UNWINDER. ON THE UNWINDER THERE IS PLACED STOP BAR, WHICH FIXES THE MATERIAL AGAINST MOVEMENT WHEN THE LINE IS STOPPED. THE STOP BAR WILL BE PLACED ACCORDING TO TECHNICAL POSSIBILITIES TO THE NEAREST ROLL OF UNWINDING AXE WINDER • THE SIDE-WALLS OF WINDER ARE CONNECTED BY WELDED CROSS-BEAMS WHICH ENSURE RELATIVE POSITION OF THE SIDE-WALLS AND STABILITY OF THE MACHINE. THE BEAMS CAN ALSO BE USED TO HANDLE THIS PART OF THE MACHINE. THERE ARE MACHINED MOUNTING AREAS ON INNER SURFACES OF THE SIDE-WALLS FOR THE WINDING SHAFT SAFETY CHUCKS, WINDING SHAFT DRIVE AND BEARING BODIES OF THE BALANCED STAINLESS STEEL FREE-RUNNING ROLLERS. THE SURFACES OF THE STAINLESS STEEL FREE-RUNNING ROLLERS ARE MACHINED • COMPENSATOR SPLITS THE WINDING TENSION FROM PRODUCTION LINE AND THE WINDER. TO INCREASE THE FRICTION COEFFICIENT AND THUS TO PREVENT SLIDING OF THE WOUND MATERIAL, COMPENSATOR ROLLER SURFACE IS FINISHED WITH A GLUED TEXTILE STRAP WITH A LAYER OF THE RUBBER. THE WOUND MATERIAL CONTACTS THE OPPOSITE SIDE TO THAT ONE WITH NANOFIBERS • THE POSITION OF THE DANCER IS MONITORED IN CONTACTLESS MANNER BY MEANS OF A CAM AND AN ANALOGUE SENSOR. INFORMATION FROM DANCER SERVES FOR THE RIGHT FUNCTION OF THE WINDER • ON THE WINDER THERE IS PLACED THE STOP BAR, WHICH FIXES THE MATERIAL AGAINST MOVEMENT WHEN THE LINE IS STOPPED. THE STOP BAR WILL BE PLACED ACCORDING TO TECHNICAL POSSIBILITIES TO THE NEAREST ROLL OF UNWINDING AXE BANANA ROLL • ROLL IS PLACED TO ADJUSTABLE BEARINGS FOR EASY SETTING OF CORRECT SPREADING EFFECT. ROLL SURFACE IS RUBBER COATED. THE BANANA ROLL IS DRIVEN TO SECURE ITS ROTATION AT LOW WINDING TENSIONS LONGITUDINAL CUTTING • INDIVIDUAL CUTTING HEADS CAN BE MANUALLY ADJUSTED TO THE DESIRED WIDTH. CUTTING IS CARRIED OUT BY PRESSURE AGAINST THE HARDENED CYLINDER - SHREDDER. CUTTING QUALITY IS RECOMMENDED TO TEST THE MATERIAL IN ADVANCE. THE EDGE TRIMS SLIDES ALLOW TO REDIRECT TRIMS TO CUSTOMER BIN OR TRIM WINDER WINDER EDGE GUIDING • THE EDGE GUIDING EQUIPMENT CONSIST OF WINDER BASE FRAME WITH TRANSVERSAL RAILS, ROLLERS MOUNTED ON WINDER MOVING FRAME, LINEAR ACTUATOR AND EDGE SENSOR INSTALLED ON ADJUSTABLE ARM. THE SENSOR MONITORS MATERIAL EDGE AND IN CASE OF EDGE POSITION DEVIATION THE WINDER FRAME IS MOVED RIGHT OR LEFT TO COMPENSATE THE MATERIAL PATH DEVIATION CONTROL SYSTEM • USER CONTROLS OF THE REWINDING IS SOLVED FROM THE MAIN CONTROL PANEL (HMI) OF NANOSPIDER LINE. SERVICE INTERVENTIONS ARE PERFORMED FROM THE SERVICE PANEL LOCATED ON THE DEVICE SPECIFICATIONS: WORKING WIDTH: 1650 mm SPEED: 0.4 TO 40 M/min +/- 1% CORES, INNER DIAMETER: 76 mm (3'') MAX. WINDING FORCE: 2000 N @ 90 mm MIN. WINDING FORCE: 80 N MAX. UNWINDING FORCE: 700 N MIN. UNWINDING FORCE: 40 N MAXIMUM DIAMETER OF ROLL: 1200 mm SAFETY FENCING • SAFETY FENCING IS NEEDED TO AVOID MECHANICAL HAZARDS IN THE CASE OF A RUNNING WINDING. FIRST THREATING OF THE SUBSTRATE IS PERFORMED WITH THE ENGINE DISCONNECTED, IE WITHOUT THE DANGER. ACCURATE FENCING DESIGN FOR COMPLETE SOS (SCOPE OF SUPPLY). VERY OFTEN IS IN SAFETY FENCING PLACE AIR PERMEABILITY TESTER OR OTHER EQUIPMENT BEFORE REWINDING. PROVIDED SAFETY FENCING COMPLIES WITH THE CURRENT MACHINERY DIRECTIVE 2006/42/EC HEIGHT: 1900 mm SAFETY DISTANCE: 120 mm PILLARS: 50 X 50 mm OR 70 X 70 mm MESH SIZE: 50 X 30 mm NUMBER OF DOORS: 1 X UNWINDER 2 X REWINDER SITE PREPARATION / CONNECTION REQUIREMENTS • ALL POWER SUPPLY IS REALIZED THOUGHT NANOSPIDER PRODUCTION LINE. IT IS NECESSARY TO CALCULATE WITH INCREASE OF ELECTRICAL POWER, SPACE AND PRESSURE AIR POWER: 10 KW VOLTAGE: 220 VOLTZ AND 50/60 Hz COMPRESSED AIR: 6 TO 8 BAR (CONNECTION POINT 60 L/min) PRODUCT SIZE AND WEIGHT UNWINDER - WITHOUT ROLL: 2800 X 2100 X 2300 mm WINDER - WITHOUT ROLL 2600 X 2200 X 1400 mm WEIGH – TOTAL 1000 KG (UNWINDER), 1800 KG (WINDER) SCOPE OF SUPPLY • RW SYSTEM • EDGE GUIDE CONTROL • BANANA ROLLER • SLITTING SYSTEM MECHANISM • 1 SLITTING KNIFE SYSTEM • SAFETY FENCING NOT IN SCOPE OF SUPPLY • SPARE PNEUMATIC SHAFT - 3" OR 6" • THE WAY OF MAT STICKING IS SOLVED BY THE BUYER AND IS NOT A PART OF DELIVERY • MACHINE FOUNDATIONS • FIRE PROTECTION • ROLL + SHAFT HANDLING • SUCTION SYSTEM FOR TRIMMED EDGES • THE LINE SPEED MEASURING DEVICE • LASER SENSOR FOR MEASURING OF PACKAGE DIAMETER FOR SIGNIFICANT INCREASING OF THE UN/WINDER CONTROL SENSITIVITY • COMPACTER ROLL ON THE WINDER • WASTE MATERIAL DISPOSAL ADHESION MODULE NS AM 1600 (WITH SHOWER) ADHESION MODULE IS DESIGNED TO ENSURE THAT THE NANOFIBER LAYER DEPOSITED ON A SUBSTRATE MATERIAL ADHERES PROPERLY TO IT WITHOUT ANY DELAMINATING FAILURES. THE EQUIPMENT IS INTENDED FOR APPLICATION OF LIQUID DISPERSION GLUES OR SIMILAR LIQUIDS ONTO THE SURFACE OF DIFFERENT SUBSTRATE MATERIALS WITH SMOOTH OR SLIGHTLY STRUCTURED SURFACES AS E.G. PAPER (FLAT AND CORRUGATED), PLASTIC FILMS, WOVEN OR NON-WOVEN TEXTILES ETC THE GLUE IS DEPOSITED ON A SUBSTRATE IN CONTACT WAY. A STEEL CYLINDER ROTATES IN A TUB FILLED WITH GLUE. GLUE IN THE TUB IS KEPT AT A CERTAIN LEVEL BY THE PERISTALTIC PUMP, WHICH ALSO KEEPS ITS CIRCULATION IN A CLOSED LOOP SPECIFICATION: WORKING WIDTH: ADJUSTABLE FROM 800 TO 1640 mm SUBSTRATE MATERIAL WIDTH UP TO 1700 mm SPEED: 1 TO 40 M/min (LIMIT DEPENDS ON THE TYPE OF SUBSTRATE AND WINDING SYSTEM PARAMETERS AND TYPE OF HOT AIR DRYER). COATING (DRY MASS): 0.5 TO 1.5 GSM (CHANGE BY 0.5 GSM PROVIDES A SIGNIFICANT CHANGE IN ADHESION) FEATURES: THE ADHESIVE MODULE CAN WORK IN TWO MODES • MODE 1 - STEEL CYLINDER IS IN CONTACT WITH A SOFT ROLLER AND THIS FOAM ROLLER COATS THE SUBSTRATE WITH A THIN LAYER OF GLUE – USED MAINLY FOR COATING OF CORRUGATED MEDIA. SOFT ROLLER IS A CONSUMABLE PART • MODE 2 - SUBSTRATE IS IN DIRECT CONTACT WITH STEEL CYLINDER, ADHESIVE IS TRANSFERRED DIRECTLY ONTO SUBSTRATE • SPEED IS THE CRUCIAL PARAMETER OF THE QUALITY OF THE ADHESION TREATMENT. OPERATING SPEED RANGE MUST BE TESTED WITH THE REQUIRED SUBSTRATE MATERIAL AND OPTIMIZED. AT TOO LOW SPEED THE ADHESIVE USUALLY DRIES OUT BEFORE IT REACHES THE SPINNING CHAMBER. ON THE OTHER HAND, TOO HIGH-SPEED LEADS TO INHOMOGENEOUS COATING. • THE HOT AIR DRYER IS USED IN COMBINATION WITH ADHESIVE MODULE. • ADHESION MODULE IS INTEGRATED TO NANOSPIDER PRODUCTION LINE, MAIN CONTROL PANEL IS USED FOR THE OPERATION. SETTING OF ADHESION MODULE STRICTLY DEPENDS ON RECIPE OF RECORD, ADHESION MODULE DOESN´T CONTAIN ANY MEASUREMENT OF AMOUNT OF GLUE. • THE INSIDE OF THE MACHINE IS EQUIPPED WITH A TAP WITH INLET AND DRAINAGE FOR CLEANING. THE WATER IS HEATED IN THE MACHINE FOR BETTER DISSOLUTION OF THE ADHESIVE RESIDUE. THE DEVICE CONTAINS DRAIN PUMP FOR USED WATER. • BETWEEN THE ADHESION MODULE AND THE NANOSPIDER LINE IS A COVERED SINGLE-CYLINDER VENTILATED PORTER FOR BETTER MATERIAL GUIDANCE IN THE TECHNOLOGY. SITE PREPARATION / CONNECTION REQUIREMENTS • ALL POWER SUPPLY IS REALIZED THROUGH NANOSPIDER PRODUCTION LINE. IT IS NECESSARY TO CALCULATE WITH INCREASED ELECTRICAL POWER, SPACE AND PRESSURE AIR • POWER: 7.5 KW • VOLTAGE: 220 VOLTZ AND 50/60 Hz • COMPRESSED AIR: 6 TO 8 BARS (CONSUMPTION 100 L/min) • TAP WATER: G THREAD ½” TO CAPACITY 20 LITERS/min • DRAIN: WASTE WATER PUMP: ½“ HOSE. • MAXIMUM HOSE LENGTH 10000 mm MAX. RECOMMENDED HEAD 3000 mm PRODUCT SIZE AND WEIGHT DIMENSIONS: 2675 X 2430 X 1470 mm + 800 mm COVERS WEIGHT: 1300 KG SCOPE OF SUPPLY • MAIN EQUIPMENT, 2 MOTORS FOR MAIN AND SOFT ROLLERS • COVERS FOR SPACE BETWEEN NANOSPIDER UNIT AND ADHESION MODULE – TENT • CONTROL SYSTEM – SWITCHBOARD – OPERATOR PANEL IS USED FROM NS LINE • MECHANISM FOR WIPING THE ADHESIVE FROM THE MAIN CYLINDER • INITIAL SET OF SOFT ROLLERS (4X) • EXPANSION SHAFT FOR MOHAIR ROLLER WITH SAFETY CLAMPS • TANK WITH PNEUMATIC MIXER (75L) – NOISE APPROX. 75DB • MEASUREMENT OF THE AMOUNT OF COATING – WEIGHT PLATFORM/SCALE • AUTOMATIC LOCK FOR SLIDING DOOR WITH SWITCH LIMIT TO SHUT DOWN THE LINE IF THE DOOR IS ACCIDENTALLY OPENED • THREE SWITCH LIMITS ON DOORS WITH DIRAC KEY ACCESS TO SHUT DOWN THE LINE IF THE DOOR IS ACCIDENTALLY OPENED • TWO EMERGENCY-STOP BUTTONS ON THE CORNERS OF THE MODULE WATER HEATER • SHOWER • DRAIN NOT IN SCOPE OF SUPPLY • SPARE SOFT ROLLERS – CONSUMABLE PARTS • GLUE • OPERATORS PANEL (USE PANEL FROM LINE) • GLUE PREPARATION STATION • ANY OTHER EQUIPMENT OF CLEAN SOFT ROLLER • WATER AND DRAIN CONNECTION – PIPING OPERATION DESCRIPTION GLUE PREPARATION TYPICALITY IS GLUE DELIVERY FROM SUPPLIER IN CONCENTRATION APPROX. 50%. FOR ADHESION MODULE IS USED TYPICALLY CONCENTRATION VALUE BETWEEN 20-30%. IF NO GLUE WEIGHT STATION IS USED, THE FOLLOWING METHOD OF GLUE PREPARATION IS RECOMMENDED • FILL ORIGINAL CONCENTRATION OF GLUE TO GLUE TANK – FOR EXAMPLE MEASURING BY LABORATORY SCALE • FILL (HOT) WATER FOR DILUTING GLUE – MEASURED BY VOLUME (HOT WATER IS RECOMMENDED FOR FASTER MIXING) • MOVE TANK TO COMPRESS AIR SUPPLY AND MIX THE GLUE SOLUTION FOR 10-30 MINUTES BY INTEGRAL MIXER WE RECOMMEND PREPARING ONLY SUCH AMOUNT OF GLUE WHICH IS NECESSARY FOR PRODUCTION – AS APPROX. AFTER 3 DAYS THERE IS RISK OF BIODEGRADATION OF THE PREPARED UNUSED GLUE GLUE DEPOSITION MEASURING (CHECK) – SCALE METHOD TANK WITH GLUE IS PLACED ON WEIGHT PLATFORM (SCALE) AND MEASURE DECREASING OF MASS IN TIME = DEPOSITION ON SUBSTRATE. MEASURING IN TIME LONGER THAN 5 MINUTES IS REQUIRED – DEPENDS ON WEIGHT PLATFORM RESOLUTION AND SETTING OF ADHESION MODULE HOT AIR DRYER HAD 1600/2000 – FIRST FEATURES: • THE HOT AIR DRYER EQUIPMENT PROVIDES ADDITIONAL DRYING OF FINAL PRODUCT. NANOFIBER LAYERS WILL LEAVE THE SPINNING UNIT WITH SOME RESIDUAL HUMIDITY (OR SOLVENT CONTENT) AND THE LAYER MUST BE DRIED BEFORE WINDING. THE HOT AIR DRYER IS NEEDED, WHENEVER THE ADHESION MODULE (APPLYING WATER-BASED GLUES) IS IN OPERATION OR THICKER NANOFIBER LAYERS ARE PRODUCED OF LOW VOLATILE SOLVENT SYSTEMS ARE GENERATED. THE DRYER ALSO REDUCES THE POLLUTION OF THE AMBIENT AIR AS IT IS VENTILATED • THE HOT AIR DRYER MAY NOT PROVIDE COMPLETE DRYING OF PRODUCED NANOFIBER LAYER IF THEY ARE TOO THICK, DENSE OR THE SPEED OF THE LINE IS TOO HIGH, THEREFORE ITS PERFORMANCE MUST BE TESTED ON PARTICULAR NANOFIBER PRODUCTS • THE EQUIPMENT IS PLACED BEHIND THE SPINNING UNIT. THE DRYER CAN USE ADDITIONAL HEATING TO SPEED UP THE DRYING PROCESS. AIR FLOW RATE AND HEATING TEMPERATURE CAN BE SET DIRECTLY FROM THE CONTROL SYSTEM AS REQUIRED BASED ON THE POLYMER SOLUTION AND AMOUNT OF ADHESIVE USED AND ON THE SPEED OF THE WHOLE NS LINE • THE HOT AIR DRYER INCLUDES A CHAMBER WITH NOZZLES, EXHAUST FAN AND RECOVERY FAN AND HEATERS. THE PROCESS AIR IS SUCKED FROM THE ROOM, PARTIALLY RECIRCULATED INSIDE THE CHAMBER AND THEN EXHAUSTED • HOT AIR DRYER IS INTEGRATED INTO NANOSPIDER PRODUCTION LINE, MAIN CONTROL PANEL IS USED FOR ITS OPERATION. SETTING OF HOT AIR DRYER IS STRICTLY DEPENDENT ON RECIPE OF RECORD, ESPECIALLY ON SETTING OF ADHESION MODULE AND TYPE OF SUBSTRATE MATERIAL. EQUIPMENT DOESN´T CONTAIN ANY MEASUREMENT OF AMOUNT OF RESIDUAL WATER • HOT AIR DRYER CONTAINS SUPPORTING ROLLERS. GEOMETRICAL SHAPE OF THIS ROLLER IS SIMILAR TO LETTER “OMEGA”. PURPOSE OF OMEGA CYLINDER IS REDUCTION OF UNSUPPORTED LENGTH OF MATERIAL. SUPPORT OF THE MATERIAL IS TYPICALLY NEEDED EACH 2 TO 3 METERS. IF MATERIAL IS NOT SUPPORTED BY OTHER EQUIPMENT (LIKE REWINDING ADHESION MODULE) IT IS NECESSARY TO USE THESE 3 CYLINDERS. CYLINDER WHICH IS IN CONTACT WITH NANOFIBERS HAS PTFE COATING. CYLINDER IN STANDARD IS NOT DRIVEN (DRIVEN ONE IS ON THE REQUEST FOR SOFT MATERIAL – CAN BE ASSEMBLED AFTER INSTALLATION) • PURPOSE OF USAGE OF TENT AROUND OMEGA CYLINDERS IS DRIVEN BY MECHANICAL SAFETY AND WITH AMBIENT ATMOSPHERE AROUND TECHNOLOGY (REDUCED ODORS, IMPROVED STABILITY OF AMBIENT ATMOSPHERE IN SPINNING CHAMBER). SPECIFICATION: WORKING WIDTH: 1600 mm SUBSTRATE MATERIAL WIDTH: UP TO 1700 mm HEATING TEMPERATURE: UP TO 80 °C POWER HEATING: UP TO 15 KW NOMINAL LENGTH OF DRYING: 2000 mm AIR CHANGE/EXHAUST: MAXIMUM UP TO 500M3/H SITE PREPARATION / CONNECTION REQUIREMENTS • ALL POWER SUPPLY IS REALIZED THROUGH NANOSPIDER PRODUCTION LINE. IT IS NECESSARY TO CALCULATE INCREASE OF ELECTRICAL POWER, SPACE AND AIR FLOW VOLTAGE: 220 VOLTZ 50/60 Hz 24 KW EXHAUST: UP TO 500 M3/H (DN 160) PRODUCT SIZE AND WEIGHT DIMENSIONS: 2200 X 1800 X 2700 mm + 900 mm FOR SUPPORTING ROLLER WEIGHT: 1500 KG SCOPE OF SUPPLY • MAIN EQUIPMENT, 1 PROCESS FAN, INLET AND OUTLET FAN • CONTROL SYSTEM – SWITCHBOARD • TENT WITH NONDRIVEN SUPPORTING ROLLERS • TWO EMERGENCY - STOP BUTTONS (ONE ON FRONT, ONE ON BACK OF HAD) • SIX SWITCH LIMITS ON THE DOORS WITH DIRAC KEY ACCESS TO SHUT DOWN THE LINE IF THE DOOR IS ACCIDENTALLY OPENED NOT IN SCOPE OF SUPPLY • OPERATORS PANEL (USE MAIN PANEL FROM LINE) DATA STORAGE AND REMOTE ACCESS FEATURES: THIS SYSTEM IS PERIODICALLY SAVING SPECIFIC PROCESS DATA AND SETTINGS FROM THE MACHINE. NO DATA STORAGE FROM WINDING SYSTEM. DATA IS ACCESSIBLE BY HTTP PROTOCOL IN LOCAL NETWORK. THIS UNIT ALSO REALIZES REMOTE ACCESS (PRIVATE AND SECURED VPN). WE ARE RECOMMENDING PERMANENT INTERNET CONNECTION FOR BETTER SERVICE CAPABILITY. ALL COMPONENTS ARE PLACED IN 19” RACK FLAT BOX – 9 UNIT TYPE. FOR RIGHT FUNCTION IS NECESSARY PERMANENT POWER SUPPLY 230V/10/16A – STANDARD PLUG. REMOTE CONTROL ENABLES DIAGNOSIS OF MOTOR FUNCTIONS, UPLOADING NEW SOFTWARE VERSIONS, ONLINE DIAGNOSIS OF THE TECHNOLOGY PARAMETERS. FURTHERMORE, THE ONLINE TROUBLESHOOTING WILL BE POSSIBLE TO SPEED UP AND MINIMIZE DOWNTIME IN THE CASE OF BREAKAGE OR MISUSE. ETHERNET COMMUNICATION IS BASED ON: SPECIFICATION: RACK: 19” RACK FLAT BOX COMPUTER: SIEMENS INDUSTRIAL PC OPERATION SYSTEM: WINDOWS + WEB ACCESS (TOSI BOX) SITE PREPARATION / CONNECTION REQUIREMENTS POWER CONSUMPTION: UP TO 1.5 KW VOLTAGE: 230V/10/16A TO STANDARD PLUG CEE7 TO PERMANENTLY CONNECT INTERNET CONNECTION: CONNECTED TO THE BUYER`S INTERNAL NETWORK OR, IF SECURITY IS CONCERN, BUYER`S DMZ (DE-MILITARIZED ZONE) IN ORDER TO GET CONNECTIVITY TO THE INTERNET NETWORK. THE RECOMMENDED SPEED IS AT LEAST 512 KBPS / 512 KBPS. PRODUCT SIZE AND WEIGHT DIMENSIONS: 1000 X 1000 X 1000 mm (19” RACK FLAT BOX) WEIGHT: 50 KG SCOPE OF SUPPLY • 19” RACK FLAT BOX (OR PLACE IN SWITCHBOARD OF MACHINE) • VPN ROUTER • DATA STORAGE MEMORY • WEB ACCESS TO DOWNLOAD DATA NOT IN SCOPE OF SUPPLY • CONNECTION TO INTERNET • OTHER TOSI BOX KEY PMS 60 L– PELLETS ONLY • THE POLYMER MIX STATION (PMS) IS DESIGNED TO PREPARE POLYMER SOLUTIONS SUITABLE FOR FURTHER USE IN THE SPINNING UNIT. THE MIX STATION CONSISTS OF THE MIXER, STAIRS, SWITCHBOARD CABINET, WITH HEATING AND COOLING UNIT, STORAGE TANK AND CONNECTION POINT • THE MIXER IS A DOUBLE WALL VESSEL, WHERE A PREPARED SOLUTION IS STIRRED AND CAN BE HEATED OR COOLED DURING PREPARATION. THE MIXER IS PLACED ON A WEIGHING PLATFORM - SCALE. THE SOLVENTS ARE DELIVERED VIA FIXED PIPING FROM EXTERNAL DRUMS, BARRELS OR CANISTERS, SOLID POLYMERS ARE FILLED IN THROUGH A FUNNEL • THE OPERATION IS ALMOST FULLY AUTOMATED, SO THAT THE OPERATOR NEEDS TO ENTER ONLY A POLYMER SOLUTION RECIPE INTO THE CONTROL SYSTEM VIA A TOUCH SCREEN. SINCE THE MIXING PROCESS IS INITIATED, THE SOLVENTS ARE DOSED AUTOMATICALLY. THE SOLID POLYMER MUST BE ADDED THROUGH A FUNNEL MANUALLY • CONTACT OF OPERATORS AND CHEMICALS USED IS ELIMINATED, AS THE POLYMER MIX STATION AND THE FILLING AND CLEANING STATION ARE CONNECTED STEADILY AND FOR ANY CHANGES IN CONFIGURATION ONLY SAFETY QUICK COUPLINGS NEED TO BE DISCONNECTED AND CONNECTED • THE SPINNING SOLUTION USED IN THE ELECTROSPINNING PROCESS CAN BE REUSED FOR PREPARATION OF A NEW BATCH OF THE SPINNING SOLUTION BY UTILIZING THE STORAGE TANK. THE DEVICE IS DESIGNED FOR OPERATION IN EX ENVIRONMENT AND COMPLIES WITH ATEX DIRECTIVE 2014/34/EU. INSIDE THE MIXING VESSEL IS ZONE 0, ABOVE THE MIXING VESSEL IS ZONE 1, AND WITHIN A 1.5 M RADIUS (SHOWN AS CIRCLE IN ABOVE DRAWING) FROM THE OUTER SURFACE (BODY) OF THE MIXING VESSEL IS ZONE • THE POLYMER MIX STATION SHOULD BE ALWAYS PLACED INTO A SEPARATE EXHAUSTED ROOM EQUIPPED WITH EMERGENCY VENTILATION, AS IT WORKS WITH HIGHER AMOUNT OF CHEMICALS. THE VENTILATION SHOULD BE DESIGNED ACCORDING TO THE LOCAL LEGISLATION REQUIREMENTS, ESPECIALLY TO THE AMOUNT AND TYPE OF CHEMICALS SUPPOSED TO BE USED. DESIGN OF THE ROOMS FOR ATEX COMPLIANCE AND VENTILATING SYSTEM IS NOT INCLUDED IN THE SCOPE OF SUPPLY SPECIFICATION: WORKING VOLUME: 60 LITERS OPERATING TEMPERATURE: 20 TO 80°C MAXIMUM VISCOSITY OF FINAL SOLUTION OF POLYMER: 1000 MPAS MAXIMUM VISCOSITY OF SOURCE COMPONENTS – LIQUIDS: 500 MPAS ACCURACY OF AUTOMATIC DOSING SOURCE CHEMICALS: ± 0.100 KG FEATURES: SITE PREPARATION / CONNECTION REQUIREMENTS ROOM - SIZE DEFINED IN LAYOUT (ROUGHLY 40 M2) - VENTILATION OF ROOM RECOMMENDED 6X PER HOUR (ACCORDING TO LOCAL REGULATION) - SPACE AROUND MIXING VESSEL (1.5 M) IS IN EX ZONE • POWER: 15 KW • VOLTAGE: 220 VOLTZ AND 50/60 Hz • COMPRESSED AIR: 5 TO 8 BAR (CONSUMPTION 600 L/min) PRODUCT SIZE AND WEIGHT DIMENSIONS: 1000 X 2000 X 1000 mm INCL. WEIGHING PLATFORM DIMENSIONS - STAIRS: 1150 X 2000 X 1150 mm DIMENSIONS - CABINET: 1150 X 2050 X 1050 mm INCL. THE BUILT - IN HEATING / COOLING UNIT DIMENSIONS - STORAGE TANK: 800 X 1000 X 1000 mm WEIGHT MIXER AND STAIRS: 1000 KG WEIGHT - CABINET: 400 KG SCOPE OF SUPPLY MIXING VESSEL • INLET FOR PELLETS • 3X INLET FOR LIQUID (SOLVENTS OR USED POLYMER SOLUTION) • LIGHT AND SIGHT GLASS IN LID • MATERIAL IN CONTACT WITH POLYMER SOLUTION – AISI 316L CONTROL PANEL STORAGE TANK – 60 L STAIRS ARE COMPLIANT WITH EN131 FILLING AND CLEANING STATION ALL CONNECTIONS AND PIPING FOR MANIPULATION OF POLYMER SOLUTION AND SOLVENTS BETWEEN SELLER PROVIDED EQUIPMENT NOT IN SCOPE OF SUPPLY PIPING CONNECTION TO CHILLER (PRODUCTION OF COLD WATER) BARRELS FOR FRESH AND WASTE CHEMICALS VENTILATION OF ROOM FIRE EXTINGUISHER CAPABILITY FOR POLYMERS IN POWDER FORM FILLING AND CLEANING STATION + SWITCHBOARD FILLING AND CLEANING STATION IS DESIGNED TO REDUCE CONTACT OF OPERATORS WITH ANY CHEMICALS DURING PROCESSES OF FILLING AND CLEANING. THE EQUIPMENT HAS THE FOLLOWING FUNCTIONS • FILL THE RESERVOIR TANKS WITH A FRESH SPINNING SOLUTION FOR FURTHER USE IN THE SPINNING UNIT • DRAIN THE RESERVOIR TANKS AND REMOVE THE SPINNING SOLUTION AFTER BEING USED IN THE SPINNING UNIT • CLEAN THE RESERVOIR TANKS • CLEAN THE SPINNING CARRIAGE THE FILLING AND CLEANING STATION CONSISTS OF THE EXHAUSTED CHAMBER WITH A TUB FOR CLEANING CHEMICALS FOR MANUAL CLEANING OF SPINNING CARRIAGES AND A SET OF PUMPS. A SCALE FOR MIXING VESSEL IS USED FOR CONTROL OF PRECISE FILLING OF THE RESERVOIR TANKS. OTHER OPERATIONS CAN BE CONTROLLED BY TIMERS. THE EQUIPMENT MUST BE CONNECTED TO AN EXHAUST DESIGN OF FILLING AND CLEANING STATION VARY ACCORDING TO SUPPLIED NANOSPIDER LINE CONFIGURATION DIMENSIONS: 650 (EXCLUDING RAMP) X 2650 X 800 mm WEIGHT: UP TO 400 KG AIR CONDITIONING UNIT • THE ATMOSPHERE IN THE SPINNING CHAMBER IS ONE OF THE MOST IMPORTANT FACTORS, INFLUENCING BOTH FIBER MORPHOLOGY AND PROCESS THROUGHPUT. THE RELATIVE HUMIDITY IN THE RANGE 20 TO 50% AND TEMPERATURE IN THE RANGE 18 TO 30°C IS TARGET FOR MOST POLYMER SOLUTION RECIPES. THE OPTIMAL RELATIVE HUMIDITY AND TEMPERATURE OF THE AMBIENT AIR DIFFER FOR EACH POLYMER SYSTEM AND BOTH FACTORS ARE OPTIMIZED EMPIRICALLY. WHILE FOR ONE POLYMER SYSTEM, THE MOST SUITABLE RH CAN BE 20%, FOR ANOTHER ONE, 35% CAN BE MUCH BETTER. USUALLY, EVEN IF THE ROOMS THE LINE IS INSTALLED IN ARE AIR CONDITIONED, THE PRECISE CONTROL IS NOT EASY AND IS USUALLY TOO EXPENSIVE. THEREFORE, IT IS NECESSARY TO HAVE THE HUMIDITY CONTROL EQUIPMENT CONNECTED DIRECTLY TO THE SPINNING UNIT TO CONTROL RELATIVE HUMIDITY (AND TEMPERATURE) INSIDE THE SPINNING CHAMBER • THE AIR CONDITIONING UNIT IS DESIGNED TO PROVIDE PRECISE CONTROL OF TEMPERATURE AND RELATIVE HUMIDITY OF THE SPINNING UNIT INLET AIR. IT IS POSSIBLE TO SET UP TEMPERATURE AND HUMIDITY INDEPENDENTLY AND KEEP BOTH OUTPUT VALUES IN QUITE NARROW RANGE • THERE ARE TWO MAIN TECHNOLOGICAL COMPONENTS OF THE A/C UNIT: DEHUMIDIFIER AND HUMIDIFIER. THE AIR THAT SHOULD BE DEHUMIDIFIED (PROCESS AIR) ENTERS THE ROTOR. THE WATER MOLECULES ARE ADSORBED IN THE SILICA GEL ROTOR. THE ROTOR IS REACTIVATED THROUGH ANOTHER AIR STREAM WHICH IS HEATED UP TO 100 TO 120 °C. THE MOISTURE LEAVES THE A/C AS WARM WET AIR • THE A/C UNIT IS ABLE TO COVER VERY LOW HUMIDITY AND IS SUBSTANTIALLY MORE EFFECTIVE THAN STANDARD DEHUMIDIFIER WORKING ON CONDENSATION PRINCIPLE. THE A/C UNIT USES CROSS FLOW RECUPERATOR OF WASTE HEAT DURING THE DEHUMIDIFYING PROCESS. IN CASE OF REMOTE ACCESS, WE OFFER REAL-TIME SERVICE SCAN OF THE A/C UNIT AT CUSTOMER’S SITE SPECIFICATION: PROCESS SIDE • PROCESS AIR FLOW (FRESH AIR): (VPA)1000 M3/H • MIN. INLET TEMPERATURE: (TIMIN) 8 °C • MAX. INLET TEMPERATURE: (TIMAX) 30 °C • MIN. INLET HUMIDITY: (ABSHIMIN) 1.5 G / KG • MAX. INLET HUMIDITY: (ABSHIMAX) 13 G / KG • OUTLET TEMPERATURE: (TO) 20 TO 25 °C • MIN. OUTLET HUMIDITY: (ABSHOMIN) 2 G / KG • MAX. OUTLET HUMIDITY: (ABSHOMAX) 9 G / KG • HUMIDITY ACCURACY: (ΔRH) + / - 3,0 % • TEMPERATURE ACCURACY: (ΔT) + / - 1,0 °C • EXTERNAL PRESSURE: (PEXT) 250 PA REGENERATION SIDE • PROCESS AIR FLOW (FRESH AIR): (VRA) 400 M3 / H • MIN. INLET TEMPERATURE: (TIMIN) 18 °C • MAX. INLET TEMPERATURE: (TIMAX) 30 °C • MIN. INLET HUMIDITY: (ABSHIMIN) 1.5 G / KG • MAX. INLET HUMIDITY: (ABSHIMAX) 13 G / KG • EXTERNAL PRESSURE: (PEXT) 150 PA • REACTIVATION HEATER: (QHEL) 10 KW FEATURES: SITE PREPARATION / CONNECTION REQUIREMENTS VOLTAGE: 3 / N / PE 3 X 400 V 50 HZ, 57A COMPRESSED AIR: N/A WATER CONNECTION: TAP WATER, 1 TO 8 BAR, 10 L/HOUR AIR DUCT CONNECTION: PROCESS AIR DN200 – SEE PARAMETERS ABOVE (PROCESS SIDE) WASTE AIR DN160 (< 60°C, <90% RH) COOLING WATER CONNECTION: WATER / GLYCOL MIXTURE RECOMMENDED (MEG 30%), IN / OUT G 1 1/2” WASTEWATER CONNECTION: DN32 (PVC PIPING) PRODUCT SIZE AND WEIGHT DIMENSIONS: 1400 X 2000 X 6000 mm WEIGHT: 2000 KG SCOPE OF SUPPLY MAIN AIR CONDITIONING UNIT TECHNICAL GUIDE CHILLED WATER ACCUMULATOR 400 L (INCLUDED) CIRCULATION PUMP (INCLUDED) REVERSE OSMOSIS SYSTEM (INCLUDED) WATER DRAIN PUMP (INCLUDED) NOT IN SCOPE OF SUPPLY ETHYLENE GLYCOL 30% (-15°C) - APPROX. 1000 L DUCTING BETWEEN THE AC AND NS LINE PIPING BETWEEN AC UNIT AND CHILLER (OR OTHER COOLING SYSTEM) - SEE HYDRAULIC FLOW PLAN BELOW CHILLER (CAN BE OFFERED) OPTIONAL EQUIPMENT AND PARTS REQUIRED FOR THE OPERATION OF NS AC1000 CHILLER – NECESSARY EQUIPMENT IF BUYER DOES NOT HAVE ANOTHER USABLE COOLING SYSTEM ALREADY INSTALLED! • TEMPERATURE STABILITY (± 2°C BY THE SET POINT) • COOLING CAPACITY MIN 20 KW • TEMPERATURE SET POINT OUT 2,0/ IN 5,0 °C ETHYLENE GLYCOL 30% (-15°C) ADDITIONAL SUPPORTIVE VENTILATOR (ACCORDING TO LOCAL NEEDS) SELLER IS NOT RESPONSIBLE FOR SUPPLY OF ANY EXTRA PARTS, WHICH ARE NOT INCLUDED IN THE SCOPE OF SUPPLY, AND WHICH DEPENDS ON EXACT PLACEMENT OF EACH PERIPHERAL PARTS NEEDED FOR THE INSTALLATION ROOM CONDITIONS INTENDED SCOPE OF POLYMERS TO BE USED, RH AND TEMPERATURE OF AMBIENT AIR ARE AMONG THE MOST IMPORTANT ASPECTS. PRIOR TO PURCHASE OF THE UNIT BY THE SELLER THE CUSTOMER MUST AGREE AND SIGN A PROTOCOL CONFIRMING THAT ALL REQUIREMENTS THAT NEED TO BE MET BY THE BUYER WILL BE FULFILLED PRIOR TO INSTALLATION. IF THE REQUIREMENTS ARE NOT MET PRIOR TO INSTALLATION, THE SELLER CANNOT GUARANTEE MEETING THE PROCESS PARAMETERS CHILLER CHILLER IS A MACHINE TO PRODUCE CHILLED WATER, WHICH IS USED FOR TAKING OUT THE HEAT DEVELOPED IN VARIOUS INDUSTRIAL PROCESSES IN NS TECHNOLOGY, CHILLED WATER IS DISTRIBUTED INTO HEAT EXCHANGERS IN NS AC UNIT AND THEN THE WATER IS RE-CIRCULATED BACK TO THE CHILLER TO BE COOLED AGAIN. THE FIRST HEAT EXCHANGER IS USED TO COOL AND DEHUMIDIFY THE INLET AIR (1ST DEHUMIDIFYING STEP) AND THE SECOND HEAT EXCHANGER IS USED FOR FINAL ADJUSTMENT OF THE REQUIRED OUTPUT TEMPERATURE OF THE AIR. DUE TO THE AIR-COOLING PRINCIPLE, THE CHILLER IS PRIMARILY INTENDED FOR OUTDOOR INSTALLATION AND OPERATION. CHILLER MIGHT BE INSTALLED ALSO INSIDE OF BUILDINGS WHERE IT BECOMES THE SOURCE OF NON-NEGLIGIBLE AMOUNT OF WASTE HEAT SPECIFICATION: COOLING CAPACITY: (QC) 25.69 KW AMBIENT TEMPERATURE MAX: 46.0 °C OUTLET / INLET WATER TEMPERATURE: (TO/TI) 2.0/5.0 °C CHILLED WATER ACCUMULATOR TANK: 100 L FEATURES: SITE PREPARATION / CONNECTION REQUIREMENTS TOTAL INPUT POWER: 11.18 KW (400V/ 3 PH / 50HZ) SURROUNDINGS: OUTSIDE PRODUCT SIZE AND WEIGHT DIMENSIONS: 75 X 1450 X 1750 mm (THE CHILLER NEEDS A FREE SPACE OF ABOUT 1.5 M FROM ALL SIDES FOR PROPER OPERATION) NET WEIGHT: 293 KG SCOPE OF SUPPLY MAIN UNIT EC FANS NOT IN SCOPE OF SUPPLY ETHYLENE GLYCOL - 30% (-15°C) PIPING BETWEEN AC UNIT AND CHILLER REGENERATIVE CATALYTIC OXIDIZER 3000-GAS EMISSION LIMITS IN MOST REGIONS DO NOT ALLOW DISCHARGE OF THESE CONCENTRATIONS DIRECTLY INTO THE ATMOSPHERE. COMBUSTION IS CHOSEN AS A UNIVERSAL WASTE AIR TREATMENT METHOD. THE EQUIPMENT SHOULD ALWAYS BE CHOSEN WITH RESPECT TO: PROCESS PARAMETERS • FLOW RATE • CONCENTRATION LOCAL REGULATIONS • EMISSION LIMITS • OTHER CONDITION FINAL FACTORY INSTALLATION • AVAILABLE ENERGY • SPACE – INSIDE OUTSIDE THIS TECHNICAL EQUIPMENT IS ONE OF POSSIBLE SOLUTION, FOR FINAL OFFER WE RECOMMENDED SPECIFIED MORE PRECISELY CATALYTIC OXIDATION WITH REGENERATION / RECUPERATION OF WASTE HEAT (RCO/CO) IN THE CASE OF EXACT PRE-DEFINED CONDITIONS AND CHARACTERISTICS OF THE WASTE GAS, IT IS POSSIBLE TO SUPPLEMENT THE RTO AND TO TECHNOLOGIES WITH CATALYST. THANKS TO THIS CATALYST, OXIDATION OF VOCS OCCURS AT LOWER TEMPERATURES, WHICH REDUCES OPERATING COSTS. TECHNOLOGIES WITH CATALYST REACH AUTOTHERMAL OPERATION AT LOWER CONCENTRATIONS OF VOCS IN THE WASTE GAS. THERMAL OXIDIZER (WITH HEAT RECUPERATION) (TO) THE TECHNOLOGY OF DIRECT COMBUSTION IS ESPECIALLY SUITABLE FOR WASTE GASES WITH HIGHER CONCENTRATIONS OF VOLATILE ORGANIC COMPOUNDS. IN ORDER TO REDUCE FUEL CONSUMPTION, A TUBULAR HEAT EXCHANGER FOR PREHEATING THE WASTE AND COMBUSTION AIR IS ADDED. REGENERATIVE THERMAL OXIDIZER (RTO) RTO SYSTEMS UTILIZE THE TECHNOLOGY OF REGENERATION OF WASTE HEAT CONTAINED IN THE EXHAUST CLEANED OFF-GAS. THERMAL EFFICIENCY OF UP TO 95 % TRANSLATES INTO LOW CONSUMPTION OF AUXILIARY FUEL EVEN FOR RELATIVELY LOW CONCENTRATIONS OF VOLATILE ORGANIC COMPOUNDS IN THE OFF-GAS. RTO TECHNOLOGIES ARE DISTINGUISHED BY THE FOLLOWING CHARACTERISTICS: • LOW CONSUMPTION OF AUXILIARY ENERGY • WIDE TURNDOWN RATIO • OPTIONAL AUTOTHERMAL OPERATION (WITHOUT CONSUMPTION OF AUXILIARY ENERGY) • LONG LIFETIME OF CERAMIC LINING • EASY OPERATION AND MAINTENANCE SPECIFICATIONS: PROCESS AIR VOLUME MAXIMUM: 3000 NM3/H MINIMUM: 1500 NM3/H PRINCIPLE: REGENERATIVE CATALYTIC OXIDIZER ENERGY FOR HEATING: NATURAL GAS 70 KW LOCATION INSIDE (FROM +3°C TO 30°C) ESTIMATED CONSUMPTION: 3000 M3 / H CONCENTRATION: 0 MG TOC / NM3 48 KW CONCENTRATION: 0.5 G / NM3 - DMAC 42 KW EMISSION TOC <20 MG / NM3 CO <100 MG/NM3 NOX <100 MG / NM3 FEATURES: SITE PREPARATION / CONNECTION REQUIREMENTS TOTAL INPUT POWER: 10 KW (400V @ 50HZ) PRESSURE AIR: DEW POINT +3°C (OUTSIDE -40°C) 6 BAR 4 NM3 / H NATURAL GAS: 150 MBAR CALORIFIC / HEATING / ENERGY VALUE: 10.2 KWH/NM3 70KW PRODUCT SIZE AND WEIGHT DIMENSIONS: 3300 mm X 3300 mm X 3400 mm (LOCATION OUTSIDE OR INSIDE) EXTERNAL SWITCHBOARD (APPROX. 1200 X 500 X 2000 mm) NET WEIGHT: 7500 KG SCOPE OF SUPPLY PROCESS CENTRIFUGAL FAN AND MOTOR COMBUSTION CHAMBER WITH CATALYTIC DAMPER SYSTEM – TO CHANGE PROSS AND REGENERATION CATALYTIC HEATER SUPPORTING STEEL STRUCTURE STACK / CHIMNEY Ø300M - 7M – FREE STANDING EXTERNAL SWITCHBOARD + CABLE UP TO 1000 mm NOT IN SCOPE OF SUPPLY CIVIL WORKS AND ANCHORING CONNECTION DUCTWORKS BETWEEN PRODUCTION NANOSPIDER LINE AND WAT CONNECTION TO UTILITIES UP TO THE BATTERY LIMITS PROCESS FLUIDS (FUEL, COMPRESSED AIR) WASTE DISPOSAL LIFTING EQUIPMENT • START-UP EMISSION ANALYSIS CONTINUOUS ANALYZER EMISSION. CABLE TRACE FOR CONNECTION BURNING UNIT AND SWITCHBOARD Learn More

C-3980 KRAFT PAPER MAKING MACHINE WITH GAS BOILER, CAPACITY 3 TO 5 T/D, NET PAPER WIDTH 1200mm

KRAFT PAPER MAKING MACHINE
WITH GAS BOILER
CAPACITY: 3 TO 5 T/D KRAFT PAPER MACHINE
1092 KRAFT CORRUGATED PAPER MACHINE
WITH RECYCLE PAPER AS RAW MATERIAL
TECHNICAL PARAMETER:
OUTPUT: KRAFT PAPER, CORRUGATED PAPER
WEIGHT: 60 TO 180G/M2
NET PAPER WIDTH: 1200mm

QUANTITY: 1

Learn More

C-3994 BARGEMOUNTED POWER PLANT, CAPACITY 220MW

A. ONCE THROUGH STEAM GENERATOR
B. BARGE
C. CHILLERS
D. AIR COMPRESSOR
E. GAS TURBINE
F. STEAM TURBINE
G. FEEDWATER SYSTEM
H. CLOSED COOLING WATER SYSTEM
I. AUXILIARY COOLING WATER SYSTEM
J. CONDENSATE POLISHING UNIT (CPU)
K. WASTE WATER SYSTEM
L. PLANT ELECTRICAL SYSTEM
M. BLACK START DG SET
N. PLANT CONTROLS AND INSTRUMENTATION
O. PLANT FIRE FIGHTING SYSTEM
P. START UP VACUUM SYSTEM
Q. STEAM TURBINE DEAERATING CONDENSER

QUANTITY: 1 PLANT

Learn More

TT-2363 LION AUTOMATIC BLOWER, NOZZLES 2, YEAR 2011 QUANTITY: 1 Learn More

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

TT-2026 AUTOMATIC GLUE SPRAY MACHINE, WIDTH 850 TO 2200mm WITH BRIDGE AND CONVEYOR AND PRESS AT THE EXIT AUTOMATIC GLUE SPRAY MACHINE APPLICATION: THE AUTOMATIC GLUE SPRAY MACHINE IS HIGHLY AUTOMATED. THROUGH INFRARED MEASUREMENT, IT CAN AUTOMATICALLY IDENTIFY THE HEIGHT AND WIDTH OF THE MATERIAL, AND AUTOMATICALLY ADJUST THE POSITION OF THE GLUE NOZZLE FOR SPRAYING ACCORDING TO THE DETECTION HEIGHT. AUTOMATIC GLUE SPRAY MACHINE CAN COMPLETE SUCH PROCESSES AS AUTOMATICALLY GLUE SPRAYING, PNEUMATIC TURNING OVER OF THE UNIT AND AUTOMATICALLY PRESSING. WITH PLC CONTROL, HIGH PRODUCTION EFFICIENCY, SINGLE SPRAYING IS ABOUT 30 SECONDS PER SHEET. IT IS SUITABLE FOR SHEETS WITH WIDTH OF 850 TO 2200mm AND HEIGHT OF 5 TO 400mm THE GLUE SPRAYING MACHINE IS SUITABLE FOR FOAM, LATEX, MATTRESS AND HOME TEXTILE INDUSTRIES. Learn More

REFERENCE NUMBER: M-1480

SLITTER REWINDER 1800mm WIDTH AND 1000mm DIAMETER-NEW MACHINE

 

TECHNICAL CHARACTERISTICS:

 

UNWINDER

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1100mm

MINIMUM WIDTH: 420mm

MAXIMUM WEIGHT: 300kgs

CORE ID: 3”

 

REWINDER:

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1000mm

MINIMUM WIDTH: 100mm

MAXIMUM WEIGHT PER SHAFT: 300kgs

CORE ID: 3”

 

MATERIAL:

TYPE: 100% PP NONWOVEN

MINIMUM: 10gsm

MAXIMUM: 150gsm

 

TENSION:

MAXIMUM: 2 PLI

 

SPEED:

METERS PER MINUTE: 250

 

DESCRIPTION:

REWINDER MACHINE FOR NONWOVEN ROLLS: UP TO 1000 mm DIAMETER AT UNWINDER AND 1200 mm AT REWINDER.

THE WORKSTATION OFFERS EASY ACCESS TO THE TENSION CONTROL AREA AS WELL AS THE TRIMMING AREA; THIS WAY, ANY MODIFICATION ON THE MATERIAL MEASUREMENTS CAN BE DONE SAFELY.

THE WORKSTATION WILL DELIVER MODULES OF ROLLED MATERIAL WITH SPECIFIC DENSITY, AND SEPARATED FROM EACH OTHER IN ORDER TO KEEP OPERATION CONDITIONS WITHIN REQUIRED QUALITY CONTROLS.

 

UNWINDER WITH SHAFT:

THERE IS A CENTRAL UNWINDING SYSTEM SUPPORTED BY A 3” STEEL EXPANSION SHAFT.

THERE IS A TENSION CONTROL SYSTEM THAT WORKS THROUGH A PNEUMATIC DISK BRAKE WITH A REPLACEABLE PADS SYSTEM.

THE UNWINDER HAS A PIVOTABLE ROLLER SYSTEM WHEREBY TENSION MAY BE MODIFIED ON ONE END TO REDUCE TENSION DIFFERENCE ON MATERIAL IF NECESSARY.

THE SAFETY CHUCK HAS A MECHANICAL MOVEMENT SYSTEM FOR SHAFT INSERTION.

THE UNWINDER HAS AN ULTRASONIC OR LASER SENSOR FOR A REAL MEASURING OF ROLL DIAMETER. THIS INFORMATION WILL HELP TO KEEP A SPECIFIC TENSION ON MATERIAL DURING ALL THE PROCESS.

 

CUTTING:

THE LONGITUDINAL SHEAR CUT SYSTEM GUARANTEES CLEAN AND SAFE TRIMMING AT EVERY MODULE. THE CUTTING SYSTEM ADAPTED TO THE MAIN TRANSMISSION GUARANTEES AN OVER SPEED THAT MAY BE REGULATED ACCORDING TO THE MATERIAL DURING EVERY STAGE OF PROCESS. THE PNEUMATIC ACTIVATION KNIVES WILL ALLOW A FAST MODIFICATION OF THE CUTTING MEASUREMENTS.

THIS ROLLER IS LOCATED AT AN EASY ACCESS AREA FOR THE OPERATOR TO BE ABLE TO MAKE CHANGES ON THE CUTTING WIDTH SAFELY. THE COUNTER KNIVES ARE ASSEMBLED TO THE ROLLER BY 3 SETSCREWS THAT FIX THEIR POSITION ON THE ROLLER. THE COUNTERKNIVES HAVE TWO FACES, SO WHEN THE FIRST FACE HAS AN IMPORTANT WEAR, IT WILL BE REMOVED FROM THE ROLLER AND THE NEW FACE WILL BE PLACED INSTEAD. THIS WILL EXTEND THE LIFESPAN OF THIS IMPORTANT COMPONENT.

SHEAR CUT KNIVES: THERE IS AN ADJUSTMENT MECHANISM TO PLACE THEM ON THE COUNTER KNIFE AND TO ADJUST THE CUTTING LOAD ACCURATELY. THE COUNTER KNIVES ARE SUPPORTED TOWARDS THE ROLLER IN ORDER TO OBTAIN A CUTOFF. THE SPEED ON THIS SYSTEM IS AN OVER SPEED IN RELATION TO THAT OF THE MATERIAL, IN ORDER TO GENERATE A CLEAN CUT.

LONGITUDINAL SHEAR CUT: PNEUMATIC ACTIVATION.

COUNTER KNIVES ROLLER WITH 3 SUPPORT PLANES FOR THE COUNTER KNIVES; 120° DISPLACEMENT FROM EACH OTHER.

19 SLITTERS ARE INCLUDED.

 

REWINDER:

PERIPHERAL REWINDER FOR NONWOVEN. THIS SYSTEM HAS A COUPLE OF MAIN ROLLERS WHERE THE MATERIAL ROLL IS FORMED.

THIS SYSTEM HAS LINEAR GUIDES FOR COMPACTION THROUGH WICH A NIP IS OBTAINED ON THE MATERIAL. THE REWINDER WILL HAVE A TRANSMISSION BASED ON A VECTORIAL-TYPE MOTOR ADAPTED TO A CYCLOIDAL REDUCER. THE TRANSMISSION HAS A MECHANICAL TORQUE CONTROL SYSTEM TO CONTROL THE TORQUE DIFFERENTIAL BETWEEN MAIN ROLLS.

THIS SYSTEM WILL HAVE A 3” EXPANSION SHAFT WHERE THE CARDBOARD CORES WILL BE INSERTED AND THE MATERIAL ROLLS WILL BE FORMED.

 

FABRIC OPENING SYSTEM:

THIS SYSTEM IS BASED ON A VARIABLE CURVATURE SYSTEM BY A CENTER KNOB AND IT IS A BAR- TYPE SYSTEM. THIS KNOB IS THERE TO CONTROL THE CURVATURE OF THE BAR WHERE MATERIAL SLIDES THROUGH. THE SLIDING BAR IS MADE OUT OF AN ULTRA LOW FRICTION MATERIAL IN ORDER TO GENERATE A SMOOTH SLIDING OF MATERIAL WITHOUT ANY TENSION ADDED. THIS WILL REDUCE WRINKLES IN A SIGNIFICANT WAY.

 

AUTOMATIC TENSION SYSTEM:

THERE IS AN OPEN LOOP AUTOMATIC TENSION CONTROL SYSTEM WITH A SENSOR FOR DIAMETER MEASURING. BY THIS SYSTEM, A REAL VALUE OF DIAMETER IS OBTAINED AT THE REWINDER. PRESSURE OF PNEUMATIC BRAKE VARIES DURING PROCESS.

 

MANUAL POSITIONING (OPTIONAL):

THE MANUAL POSITIONING SYSTEM IS BASED ON THE POSITION CONTROL OF THE COUNTER KNIVES. THE MODULE IS POSITIONED AT A DESIRED CUTTING PARAMETER AND THE COUNTER KNIFE WILL PHYSICALLY COME ACROSS IT. THE REAL POSITION OF MODULE WILL BE SHOWN ON A SCREEN THAT OPERATOR WILL BE CONSTANTLY SUPERVISING. THIS SCREEN WILL SHOW THE REAL MEASUREMENTS OF THE CARRIAGE IN RELATION TO THE LAST ONE OR AS AN ABSOLUTE REFERENCE. OPERATOR WILL BE ABLE TO RESET THE MEASUREMENT ONCE THE COUNTER KNIFE IS REPLACED AND WILL REPEAT THIS PROCESS EVERY TIME A COUNTER KNIFE IS POSITIONED.

A DISPLAY WILL SHOW THE DESIRED POSITION IN MILLIMETERS OR INCHES.

THIS SYSTEM CAN SHOW MEASUREMENT IN AN EITHER ABSOLUTE OR INCREASING WAY.

POSITION TOLERANCE: +/- 0.30 mm.

THE POSITIONER IS INSTALLED ON A SUPPORT THAT WILL BE LOCATED ON THE REWINDER BENCHES. THEREFORE, THERE WILL BE AN EASY ACCESS TO SYSTEM AND AN EASY REPETITION OF POSITIONING PROCESS.

 

UNLOADING ROLL TABLE:

A HYDRAULIC PIVOTEABLE TABLE WILL HAVE AS MAIN FUNCTION THE UNLOADING OF FINISHED ROLLS THAT THEN WILL BE LOCATED ON FLOOR LEVEL. THIS SYSTEM WILL EJECT THE ROLL AND THEN IT WILL BE RECEIVED AT THE PIVOTING TABLE FOR AN EFFICIENT UNLOADING.

THE UNLOADING TABLE WILL ALSO WORK AS A PROTECTION FOR THE OPERATOR.

THIS EQUIPMENT WILL HAVE SECURITY CURTAINS AT FRONT TO KEEP OPERATOR FROM ENTERING THE REWINDING AREA. THERE WILL BE AN EMERGENCY STOP BUTTON OR WIRE WHERE OPERATOR WORKS AND WILL ALSO HAVE PHYSICAL PROTECTION WITH SECURITY SWITCHES AT CUTTING AREA.

 

CONTROL:

HMI CENTRAL CONTROL SYSTEM WITH TOUCH SCREEN TO PROGRAM THE OPERATION CYCLE AND ALL THE MATERIAL CHARACTERISTICS. OPERATOR WILL HAVE ACCESS TO ALL OPERATION PARAMETERS IN ORDER TO BE ABLE TO MAKE CHANGES ON THE EQUIPMENT OPERATION CONDITIONS, AND THEREFORE OBTAIN MATERIAL ROLLS WITH SPECIFIC DENSITIES.

TRANSMISSION: VECTORIAL MOTO REDUCER WITH 1000:1 TORQUE.

DIGITAL METER COUNTER WITH DISPLAY AND AUTOMATIC STOP AT DEFINED DISTANCE.

 

DOCUMENTS INCLUDED:

THE MACHINE WILL BE DELIVERED WITH THE FOLLOWING DOCUMENT:

OPERATION MANUAL

MAINTENANCE MANUAL

SAFETY MANUAL

ELECTRIC DIAGRAMS

CONTROL SYSTEM MANUAL

PLC BACKUP

REQUIREMENTS:

ELECTRIC 15 KW, 440 VAC, TRI PHASE.

PNEUMATIC 6 BAR - 60 LTS. / MIN.

 

DUCTS AND WIRING:

DUCTS AND WIRES RUNNING FROM UTILITIES SOURCES TO THE CONTROL PANEL AND FROM THE CONTROL PANEL TO THE MACHINE WILL BE AT CUSTOMER COSTS AND MUST BE DONE ACCORDING TO THE INSTRUCTIONS SHOWN IN OUR DIAGRAMS

 

SIEMENS PLC

Learn More

P-5075 BUHLER VARIABLE PROFILE ROASTER 20 KILOS

THIS ROASTER OFFERS EXACTLY WHAT CUSTOMERS NEED TO PRODUCE TOP-QUALITY COFFEE. AN INNOVATIVE AND EASY-TO-USE PLC CONTROL SYSTEM ENSURES CONSTANT QUALITY DURING PRODUCTION BUT ALSO RETAINS THE ABILITY TO INFLUENCE THE PROCESSING WHEN NECESSARY. OPTIMIZED PARAMETERS CAN BE SAVED IN THE MACHINE’S MEMORY AND RE-USED. THE MACHINE IS MADE OF STAINLESS STEEL AND OTHER HIGH-QUALITY MATERIALS WHICH PROVIDE SUPERIOR HYGIENE AND MAKE CLEANING COMFORTABLE. THIS ROASTER PROVES THAT DURABILITY AND A MODERN DESIGN CAN BE COMBINED.

THE ROASTER BECOMES A PLUG-AND-PLAY MACHINE BY THE COMBINATION OF SEPARATE COOLING AND HEATING FANS WHICH ALLOW TO ROAST AND COOL AT THE SAME TIME WITH THE INCLUDED CYCLONE. HOT AIR IS THE BEST CHOICE TO ENSURE A UNIFORM ROAST, BECAUSE OF THE HOMOGENOUS HEAT TRANSFER.

THE VARIABLE DRUM SPEED OF THE ROASTING CHAMBER AND THE TWO STEP BURNER ALWAYS DELIVER THE BEST CONDITIONS FOR THE PRODUCT – NO MATTER IF THE BEANS ARE HEAVY AND SMALL AT THE BEGINNING OF THE PROCESS OR IF THEY HAVE ALREADY BECOME LIGHTER TOWARDS TO THE END OF THE ROAST. THE HELICOIDAL BLADES POWERED BY A VARIABLE DRUM SPEED DRIVE OFFER A PERFECT BLENDING AND AN OPTIMAL HEAT EXCHANGE AT ANY TIME OF THE PROCESS. MOREOVER, THE ERGONOMICALLY DESIGNED ROASTER PROVIDES MAXIMUM SAFETY.

THIS ROASTER WAS DESIGNED TO PROVIDE SMALL AND MEDIUM-SIZED COMPANIES WITH A FLEXIBLE HIGH-QUALITY SOLUTION. THE SOPHISTICATED DESIGN OF THE ROASTING MACHINE PLUS MODERN PROCESS TECHNOLOGY ENSURES A HIGH-QUALITY COFFEE PRODUCT THAT IS UNIFORMLY ROASTED – FROM THE SURFACE TO THE CORE OF EVERY SINGLE COFFEE BEAN.

THE COFFEE AND THE HOT AIR TEMPERATURE AS WELL AS THE ROASTING TIME PER BATCH IS PERMANENTLY MONITORED VIA THE TOUCH SCREEN. THE MACHINE’S DESIGN FEATURES AND INSULATING MATERIALS REDUCE INERTIA AND HEAT LOSS TO A MINIMUM, WHICH IMPACTS POSITIVELY ON WORKING ENVIRONMENTS AND FUEL CONSUMPTION.

FEATURES:
AUTOMATIC AND EASY-TO-USE PLC CONTROL SYSTEM WITH INTEGRATED TOUCH PANEL, PARAMETER MEMORY, TEMPERATURE TREND AND SAFETY FEATURES.
GOOD VALUE FOR MONEY.
INDIRECT, CONVECTIVE HOT-AIR SYSTEM FOR UNIFORM ROASTING.
FULL RANGE HEAT CONTROL - BURNER MODULATES BETWEEN 130,000 BTU ALL THE WAY DOWN TO A MERE 20,000 BTU
VARIABLE DRUM SPEEDS OFFER OPTIMAL HEAT TRANSFER AND PRODUCT QUALITY.
FUNCTIONAL AND ATTRACTIVE MACHINE DESIGN MADE OF HIGH-QUALITY MATERIAL.
STATE-OF-THE-ART TECHNOLOGY AND A PLC CONTROL SYSTEM OFFER USER-FRIENDLY AND EFFICIENT COFFEE ROASTING.
A WIDE VARIETY OF GREEN COFFEE CHARACTERISTICS AND BLENDS CAN BE PROCESSED TO HIGH-CLASS COFFEE PRODUCTS.
A USER-FRIENDLY AUTOMATION-PANEL ALLOWS THE PERFECT CONTROL OVER VARIOUS PROCESS PARAMETERS.
UL LISTED AND MADE RIGHT HERE IN MINNEAPOLIS.
GAS CONSUMPTION: RATED AT MAXIMUM - UP TO 150,000BTU (44KW/HR) OPERATES BEST BETWEEN 75 - 80,000 BTU

OPTIONAL FEATURES:
PNEUMATIC FEEDER
PNEUMATIC DESTONER/DISCHARGE UNIT
AFTERBURNER

QUANTITY: 1

Learn More

REFERENCE NUMBER: T-6565

PERSONAL PROTECTIVE EQUIPMENTS FOR SALE

 

ITEM 001

DISPOSABLE PROTECTIVE CLOTHING

MODEL: 500B

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

SIZES: S, M, L, XL, XXL, 3XL

 

FEATURES:

GARMENTS ARE COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

ONE-PIECE COVERALL WITH HOOD, ZIPPER AT FRONT OPENING COVERED BY FLAP, ELASTICATED CUFFS, ANKLES, HOOD AND WAIST.

STANDARDS: EN 14126: 2003, CE5-B, CE6-B

 

APPLICATIONS:

TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALSDUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTIONEPIDEMIC PREVENTION SERVICESAPPLICATION FOR GARMENTS INCLUDE THOSE FOUND IN PHARMACEUTICAL HANDLING, CHEMICALPROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 40PCS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 40 PCS / CARTON

WEIGHT: 13 KG / CARTON

INDUSTRIAL

 

ITEM 002

DISPOSABLE PROTECTIVE CLOTHING

MODEL: 400B

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

SIZES: S, M, L, XL, XXL, 3XL

 

FEATURES:

GARMENTS ARE COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.ONE-PIECE COVERALL WITH HOOD,ZIPPER AT FRONT OPENING COVERED BY FLAP, ELASTICATED CUFFS, ANKLES, HOOD AND WAIST, HEAT SEALED SEAMS WITH TAPE.

STANDARDS: EN 14126: 2003, CE4-B, CE5-B, CE6-B

 

APPLICATIONS:

IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

APPLICATIONS FOR IT INCLUDE MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 40PCS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 40 PCS / CARTON

WEIGHT: 13.5KG / CARTON

INDUSTRIAL

 

ITEM 003

DISPOSABLE PROTECTIVE BOOT COVER

MODEL: BT500

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE BOOT COVER

SIZES: 480mmIN HEIGHT X 350mm IN SOLE LENGTH

 

FEATURES:

BOOT COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE5-B, CE6-B

 

APPLICATIONS:

TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS.

DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION.

EPIDEMIC PREVENTION SERVICES.

APPLICATION FOR BOOT COVER INCLUDE THOSE FOUND IN PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 150 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 150 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 10.6KG / CARTON

INDUSTRIAL

 

ITEM 004

DISPOSABLE PROTECTIVE BOOT COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: BT501

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE

BOOT COVER SIZES: 480mm IN HEIGHT X 350mm IN SOLE LENGTH

 

FEATURES:

SLIP-RETARDANT SOLE, BOOT COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE5-B, CE6-B

 

APPLICATIONS:

TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS.

DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION.

EPIDEMIC PREVENTION SERVICES.

APPLICATION FOR THIS INCLUDE THOSE FOUND IN PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 150 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 150 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 11.1 KG / CARTON

INDUSTRIAL

 

ITEM 005

DISPOSABLE PROTECTIVE BOOT COVER

MODEL: BT400

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE BOOT COVER

SIZES: 500mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

BOOT COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE4-B, CE5-B, CE6-B

 

APPLICATIONS:

IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

APPLICATIONS FOR IT INCLUDE MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 150 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 150 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 11.6 KG / CARTON

INDUSTRIAL

 

ITEM 006

DISPOSABLE PROTECTIVE BOOTS COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: BT401

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE BOOT COVER

SIZES: 500mmIN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

SLIP-RETARDANT SOLE, BOOT COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YETREPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE4-B, CE5-B, CE6-B

 

APPLICATIONS:

IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

APPLICATIONS FOR IT INCLUDE MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 150 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 150 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 11.2KG / CARTON

INDUSTRIAL

 

ITEM 007

DISPOSABLE PROTECTIVE SHOES COVER

MODEL: ST500

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE SHOE COVER

SIZES: 300mmIN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

SHOE COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDINGAN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE5-B, CE6-B

 

APPLICATIONS:

TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION.

EPIDEMIC PREVENTION SERVICES.

APPLICATION FOR SHOE COVER INCLUDE THOSE FOUND IN PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 7.3KG / CARTON

INDUSTRIAL

 

ITEM 008

DISPOSABLE PROTECTIVE SHOES COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: ST501

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE SHOE COVER

SIZES: 300mmIN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

SLIP-RETARDANT SOLE, SHOE COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE5-B, CE6-B

 

APPLICATIONS:

TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS.

DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION.

EPIDEMIC PREVENTION SERVICES.APPLICATION FOR THIS INCLUDE THOSE FOUND IN PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm
WEIGHT: 7.8 KG / CARTON

INDUSTRIAL

 

ITEM 009

DISPOSABLE PROTECTIVE SHOES COVER

MODEL: ST400

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE SHOE COVER

SIZES: 300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

SHOE COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.

ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.

BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT.

STANDARDS: EN 14126: 2003, CE4-B, CE5-B, CE6-B

 

APPLICATIONS:

IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS. APPLICATIONS FOR IT INCLUDE MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / BOX

CARTON SIZE: 650 X 400 X 400mm

WEIGHT: 8.3 KG / CARTON

INDUSTRIAL

 

ITEM 010

DISPOSABLE PROTECTIVE SHOES COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: ST401

MATERIAL: NON-WOVEN MICROPOROUS LAMINATE FILM

PRODUCT NAME: DISPOSABLE PROTECTIVE SHOE COVER

SIZES: 300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

SLIP-RETARDANT SOLE, SHOE COVER IS COMPOSED OF NON-WOVEN MICROPOROUS LAMINATE FILM, 65G/M2, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT.

PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS.
ANTI-STATIC PROPERTIES.

PROTECTION AGAINST INFECTIOUS DISEASES.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT. STANDARDS: EN 14126: 2003, CE4-B, CE5-B, CE6-B

 

APPLICATIONS:

IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS. APPLICATIONS FOR IT INCLUDE MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEARINDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / BOX

CARTON SIZE: 650 X400 X 400mm

WEIGHT: 8.8 KG / CARTON

INDUSTRIAL

 

ITEM 011

DISPOSABLE PROTECTIVE CLOTHING

MODEL: TK1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC

SIZES: 170/M (165-175), 175/L (170-180), 180/XL(175-185)

 

FEATURES:

1.GARMENTS ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.GARMENTS IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YETREPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.TUNNELLED ELASTICATION AT WRISTS, ANKLES AND FACE, THUMB LOOPS5.

5.ANTI-STATIC PROPERTIES

6.PROTECTION AGAINST INFECTIOUS DISEASESCERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS
2.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION

3.EPIDEMIC PREVENTION SERVICES

4.PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 60PCS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 60 PCS / CARTON

WEIGHT: 13 KG / CARTON

STANDARDS: EN14126-2003, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 012

DISPOSABLE PROTECTIVE CLOTHING

MODEL: JT1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC

SIZES: 170/M (165-175), 175/L (170-180), 180/XL(175-185)

 

FEATURES:

1.GARMENTS ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.GARMENTS IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.BLUE TAPED SEAMS FOR OPTIONAL PROTECTION AND GOOD VISIBILITY

5.TUNNELLED ELASTICATION AT WRISTS, ANKLES AND FACE, THUMB LOOPS

6.ANTI-STATIC PROPERTIES

7.PROTECTION AGAINST INFECTIOUS DISEASES

 

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 4-B, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

2.MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONSAND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 60PCS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 60 PCS / CARTON

WEIGHT: 13.5 KG / CARTON

STANDARDS: EN14126-2003, CE4-B, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 013

DISPOSABLE PROTECTIVE BOOT COVER

MODEL: XT1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 480mmIN HEIGHT X 350mm IN SOLE LENGTH

 

FEATURES:

1.BOOT COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.BOOT COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRONIN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.SHOE COVER WITH ELASTIC TOP5.ANTI-STATIC PROPERTIES6.PROTECTION AGAINST INFECTIOUS DISEASES

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS

2.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION

3.EPIDEMIC PREVENTION SERVICES

4.PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / CTN

STANDARDS: EN14126-2003, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 014

DISPOSABLE PROTECTIVE BOOT COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: BT1S

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

 SIZES: 480mm IN HEIGHT X 350mm IN SOLE LENGTH

 

FEATURES:

1.ANTISLIP DESIGN ON THE SOLE

2.BOOT COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

3.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

4.BOOT COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

5.SHOE COVER WITH ELASTIC TOP6.ANTI-STATIC PROPERTIES7.PROTECTION AGAINST INFECTIOUS DISEASES

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVEAGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS

2.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION

3.EPIDEMIC PREVENTION SERVICES

4.PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / CTN

STANDARDS: EN14126-2003, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 015

DISPOSABLE PROTECTIVE BOOT COVER

MODEL: XT-JT1MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 500mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.BOOT COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.BOOT COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.BOOT COVER WITH ELASTIC TOP

5.BLUE TAPED SEAMS FOR OPTIONAL PROTECTION AND GOOD VISIBILITY

6.ANTI-STATIC PROPERTIES

7.PROTECTION AGAINST INFECTIOUS DISEASES

'CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 4-B, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

 2.MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / CTN

STANDARDS: EN14126-2003, CE4-B, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 016

DISPOSABLE PROTECTIVE BOOT COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: XT-JT1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 500mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.BOOT COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.BOOT COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.BOOT COVER WITH ELASTIC TOP

5.BLUE TAPED SEAMS FOR OPTIONAL PROTECTION AND GOOD VISIBILITY

6.ANTI-STATIC PROPERTIES

7.PROTECTION AGAINST INFECTIOUS DISEASES

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 4-B, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

2.MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE: 200 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 200 PAIRS / CTN

STANDARDS: EN14126-2003, CE4-B, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 017

DISPOSABLE PROTECTIVE SHOE COVER

MODEL: ST1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.SHOE COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.SHOE COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.SHOE COVER WITH ELASTIC TOP

5.ANTI-STATIC PROPERTIES

6.PROTECTION AGAINST INFECTIOUS DISEASES

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS

2.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION

3.EPIDEMIC PREVENTION SERVICES

4.PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE: 250 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 250 PAIRS / CARTON

STANDARDS: EN14126-2003, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

 

ITEM 018

DISPOSABLE PROTECTIVE SHOE COVER (WITH ANTISLIP STRIP ON THE SOLE)
MODEL: ST1S

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.ANTISLIP DESIGN ON THE SOLE

2.SHOE COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

3.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

4.SHOE COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

5.SHOE COVER WITH ELASTIC TOP6.ANTI-STATIC PROPERTIES7.PROTECTION AGAINST INFECTIOUS DISEASES

CERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.TRAFFIC CONTROLLING, ROAD CONTROLLING, TRANSPORTATION OF HAZARDOUS CHEMICALS

2.DUTY IN KEY AREAS, POLICE FOR SENSITIVE INCIDENTS, CUSTOMS BORDER INSPECTION

3.EPIDEMIC PREVENTION SERVICES

4.PHARMACEUTICAL HANDLING, CHEMICAL PROCESSING, THE OIL AND GAS INDUSTRY, GENERAL MAINTENANCE AND OPERATIONS, AUTOMATIC SPRAY PAINTING AND MANY OTHERS.

 

PACKAGE:

250 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 250 PAIRS / CARTON

STANDARDS: EN14126-2003, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 019

DISPOSABLE PROTECTIVE SHOE COVER

MODEL: ST-JT1

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES:300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.SHOE COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

2.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

3.SHOE COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

4.SHOE COVER WITH ELASTIC TOP

5.BLUE TAPED SEAMS FOR OPTIONAL PROTECTION AND GOOD VISIBILITY

6.ANTI-STATIC PROPERTIES

7.PROTECTION AGAINST INFECTIOUS DISEASESCERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 4-B, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

2.MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE:

250 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 250 PAIRS / CARTON

STANDARDS: EN14126-2003, CE4-B, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 020

DISPOSABLE PROTECTIVE SHOE COVER (WITH ANTISLIP STRIP ON THE SOLE)

MODEL: ST-JT1S

MATERIAL: DUPONTTM TYVEK® 1422A FABRIC, 41G/M2

SIZES: 300mm IN HEIGHT X 420mm IN SOLE LENGTH

 

FEATURES:

1.ANTISLIP DESIGN ON THE SOLE

2.SHOE COVER ARE COMPOSED OF FLASH SPUN HIGH DENSITY POLYETHYLENE, PROVIDING AN IDEAL BALANCE OF PROTECTION, DURABILITY AND COMFORT

3.BREATHABLE, LIGHTWEIGHT AND FLEXIBLE MATERIAL FOR EXCEPTIONAL WEARER COMFORT

4.SHOE COVER IS PERMEABLE TO BOTH AIR AND WATER VAPOUR, YET REPELS WATER-BASED LIQUIDS AND AEROSOLS. IT OFFERS AN EXCELLENT BARRIER AGAINST FINE PARTICLES AND FIBRES (DOWN TO 1 MICRON IN SIZE), IS ULTRA-LOW-LINTING. SILICON NON-ADDED

5.SHOE COVER WITH ELASTIC TOP

6.BLUE TAPED SEAMS FOR OPTIONAL PROTECTION AND GOOD VISIBILITY

7.ANTI-STATIC PROPERTIES8.PROTECTION AGAINST INFECTIOUS DISEASESCERTIFICATIONS: CHEMICAL PROTECTIVE CLOTHING, CATEGORY III, TYPE 4-B, 5-B AND 6-B, EN 14126 (PROTECTIVE CLOTHING AGAINST INFECTIVE AGENTS), ANTISTATIC TREATMENT (EN 1149-5) -ON BOTH SIDES

 

APPLICATION:

1.IT CAN PROVIDE BARRIER AND PROTECTION FOR MEDICAL STAFF TO DIRECTLY CONTACT WITH PATIENTS OR SUSPECTED PATIENTS.

2.MAINTENANCE AND DISMANTLING JOBS IN THE NUCLEAR INDUSTRY, PHARMACEUTICAL MANUFACTURING OR IN RESEARCH AND BIOSECURITY LABORATORIES, AS WELL AS IN MEDICAL APPLICATIONS AND WHEN EXPOSED TO BIOLOGICAL HAZARDS.

 

PACKAGE:

250 PAIRS / CTN

CARTON SIZE: 650 X 400 X 400mm

MOQ: 250 PAIRS / CARTON

STANDARDS: EN14126-2003, CE4-B, CE5-B, CE6-B

MEDICAL / INDUSTRIAL

 

ITEM 021

MEDICAL GOGGLES (AUTOCLAVAB LE, REUSABLE)

DESIGN: RETRO WIDE VIEWING ANGLE, AIRTIGHT ANTI-FOG LIQUID SPLASH AND LEAKAGE, VENTILATION DESIGN, SUITABLE FOR MOST CORRECTIVE GLASSES, ULTRA-LIGHT WEIGHT, COMFORTABLE TO WEAR FOR A LONG TIME WITHOUT STRIAE, CAN WITHSTAND HIGH TEMPERATURE STERILIZATION IN HOSPITAL 121 °C / 30MIN / REUSABLE 15 TIMES, CAN MAINTAIN STRONG ANTI-FOG AFTER STERILIZATION (KN GRADE) LENS: MEDICAL GRADE POLYCARBONATE -IMPACT RESISTANT, STRONG ANTI-FOG (KN GRADE) COVER BODY: MEDICAL GRADE HIGH TEMPERATURE TPR -SUPER COMFORTABLE, LONG-TERM WEAR WITHOUT MARKS, HIGH NOSE BRIDGE SEAL, VENTILATION DESIGN, AND BLOCK PARTICLES OF 0.5μM DIAMETER, SUITABLE FOR MOST CORRECTIVE GLASSES.

HEADBAND: 24mm MEDICAL SILICONE -THREE-STAGE ADJUSTABLE

NET WEIGHT: 101.8

EXECUTIVE STANDARD: CE: EN166: 2001; ANSI Z87.1: 2005

 

PACKAGE:

WEIGHT: 102G (1 PAIR+PRODUCT SPECIFICATION)

BOX SIZE: 195X 75X 90mm

CARTON SIZE: 660 X 460 X 420mm

PACKAGE: 1 PAIR / BAG, 10 PAIRS / BOX, 12 BOXES / CARTON

MOQ: 10 PAIRS / BOX

STANDARDS: CE, EN166

MEDICAL / INDUSTRIAL

 

ITEM 022

GOGGLES

FUNCTION: ANTI UV 99%, ANTI ENERGY IMPACT, OPTICAL CLASS 1 OF TRANSMITTANCE ANTI DROPLETS AND SPLASHES OF LIQUIDS, ANTI MOLTEN METALS ANDHOT SOLIDS, ANTI FOG

DESIGN: CLASSIC UNIVERSAL STYLE, VENTILATION VALVE DESIGN -REDUCE THE NEGATIVE PRESSURE FEELING OF WEARING FOR A LONG TIME, ELASTIC BELT PULL CARD DESIGN -CONVENIENT FOR THE WEARER TO TIGHTEN

STANDARD: GB 14866, EN 166 ANSI Z87.1CERTIFICATION: CE: EN 166 (3 4 9 B)

 

APPLICATION:

MANUFACTURE, LABORATORY, MEDICAL PLACE

PACKAGE: WEIGHT: 102G (1 PAIR+PRODUCT SPECIFICATION)

BOX SIZE: 195X 75X 90mm

CARTON SIZE: 660 X 460 X 420mm

 

PACKAGE:

1 PAIR / BAG, 10 PAIRS / BOX, 10 BOXES / CARTON

MOQ: 10 PAIRS / BOX

STANDARDS: GB14866, EN 166 Z87.1

INDUSTRIAL

 

ITEM 023

GOGGLES

COVER BODY:

1.IMPORTED MODIFIED PVC -OUTSTANDING CHEMICAL RESISTANCE, BLUE-TINT-PANORAMIC VIEW

2.BEVELED MICROPORE DISTRIBUTION AERODYNAMIC DISTRIBUTION -LONG-TERM WEAR WILL NOT BE UNCOMFORTABLE DUE TO NEGATIVE PRESSURE
3.DEEP SPACE -YOU CAN WEAR IT FREELY WHEN WEARING GLASSES

 

LENS:

1.IMPORTED MODIFIED POLYCARBONATE -NATURAL EXCELLENT ALL-WEATHER IMPACT RESISTANCE, WHILE EXCEEDING THE HIGHEST LEVEL OF LIGHT TRANSMITTANCE STANDARD, CLOSE TO THE THEORETICAL TRANSMITTANCE LIMIT OF THE MATERIAL ITSELF

2.ANTI-FOG COATING PROCESS (AF) -NO INFLUENCE OF WATER VAPOR

3.UV PROTECTION 99% -AVOID LONG-TERM DAMAGE TO THE EYE BY UV RAYS HEADBAND: ONE-PIECE COVER BODY -HIGH STRENGTH AND LONG SERVICE LIFE; EASY TO PULL AND LOOSEN ACCORDING TO THE HEAD CIRCUMFERENCE AFTER WEARING; COTTON-LIKE MATERIAL -COMFORTABLE SWEAT ABSORPTION

 

APPLICATION: WORKING ENVIRONMENT WITH THE RISK OF CHEMICAL LIQUID, ULTRAVIOLET, FOREIGN OBJECT IMPACT, ALTITUDE WIND AND SAND, FOG (ANTI-CHEMICAL CORROSION, LIQUID SPLASHING ANTI-UV ULTRAVIOLET ANTI-FOG ANTI-IMPACT)

EXECUTIVE STANDARDS: EN 166 (1 FT); EN 170 (2C-1.2); ANSI Z87.1; GB 14866PRODUCT CERTIFICATION: CE

 

PACKAGE:

WEIGHT: 109G (1 PAIR+PRODUCT SPECIFICATION)BOX SIZE: 195X 75X 90mm

CARTON SIZE: 660 X 460 X 420mm

PACKAGE: 10 PAIRS / BOX, 12 BOXES / CARTON

MOQ: 10 PAIRS / BOXEN 166 (1 FT); EN 170 (2C-1.2); ANSI Z87.1; GB 14866

INDUSTRIAL

 

ITEM 024

MEDICAL SAFETY GOGGLES

BODY: CLASSIC UNIVERSAL TYPE, MEDICAL GRADE SILICA GEL -EXCELLENT ANTI SKIN ALLERGY, LONG-TIME WEAR COMFORT, EXCELLENT LIQ/ GAS TIGHTNESS, AND CAN ADAPT TO CORRECTIVE GLASSES

LENS: MODIFIED POLYCARBONATE PC -EXCELLENT IMPACT RESISTANCE AND DOUBLE-SIDED ANTI FOG COATING

STANDARD: GB32166.1-2016, EN 61000

CERTIFICATION: CE: EN61000

 

PACKAGE: OUTER SIZE: 810 X 352X 428mm

1UNIT/BAG 10 BAGS/BOX

20BOXES/CTN GW: 15KGS

MOQ: 10 PAIRS / BOX

STANDARD: GB32166.1-2016

CERTIFICATION: CE: EN166

MEDICAL STAFF, CLEAN ROOM

 

ITEM 025

MEDICAL SAFETY GOGGLES

BODY:CLASSIC UNIVERSAL TYPE, MEDICAL GRADE SILICA GEL -EXCELLENT ANTI SKIN ALLERGY, LONG-TIME WEAR COMFORT, VENTILATION VALVE DESIGN -REDUCE NEGATIVE PRESSURE FEELING FOR A LONG TIME, AND CAN ADAPT TO CORRECTIVE GLASSES

LENS: MODIFIED POLYCARBONATE PC -EXCELLENT IMPACT RESISTANCE AND DOUBLE-SIDED ANTI FOG COATING

STANDARD: GB32166.1-2016, EN 61000

CERTIFICATION: CE: EN61000

 

PACKAGE: CARTON SIZE: 810 X 352X 428mm

1UNIT/BAG 10 BAGS/BOX

20BOXES/CTN GW: 15KGS

MOQ: 10 PAIRS / BOX

STANDARD: GB32166.1-2016

CERTIFICATION: CE: EN166

MEDICAL STAFF, CLEAN ROOM

 

ITEM 026

DISPOSABLE MEDICAL FACE SHIELD (NON STERILE)

FEATURES: PREVENT THE RISK OF CROSS INFECTION DUE TO SPLASHING OF LIQUID INFECTION SOURCES SUCH AS SALIVA/BLOOD. HIGH TRANSMITTANCE FILTER MATERIAL -MINIMIZE COLOR DIFFERENCE AND EYE DISCOMFORT, LIGHT AND FLEXIBLE -SUITABLE FOR LONG TIME WEARING WITHOUT WEIGHT BEARING. AND WILL NOT EASILY OCCUR BENDING AND FRACTURE PHENOMENON. SOFT AND CUSHIONED FOREHEAD AND ELASTIC BAND MAKE IT EASY TO WEAR, LIGHT AND COMFORTABLE WITHOUT ANY LIGATURE MARKS. ANTI FOG-AVOID WATER VAPOR ACCUMULATION ON THE SHIELD, WHICH MAY AFFECT THE VISUAL OBSERVATION. SURFACE COATING-TO AVOID SCRATCHES AFFECTING THE LIGHT TRANSMITTANCE AND DURABILITY OF THE SHIELD. FUNCTION: PREVENT LIQUID SPLASHING AND ANTI-FOG.

 

APPLICATION: WORKING ENVIRONMENT WITH RISK OF CROSS INFECTION CAUSED BY SPLASHING OF SALIVA / BLOOD AND OTHER LIQUID INFECTION SOURCES, SUCH AS HOSPITAL, POLICE STATION, CHECKPOINT, JAIL, ETC.

SPECIFICATION: 3200 X 2200 X 2mm

MEAS: 690mm X 390 X 400mm/8.4KGS1 UNIT/SMALL BAG 10 SMALL BAG / MEDIUM BAG, 20 MEDIUM BAG /CTN

 

PACKAGE: CARTON SIZE: 480 X 330 X 380mm

1UNIT/BAG 10 SMALL-BAGS/MIDDLE BAGS 20 MIDDLE BAGS/CTN (200PCS/CARTON)

GW: 15KGS

STANDARDS: CE: EN166

MEDICAL / INDUSTRIAL

 

ITEM 027

SAFETY GLASSES

LENS: CLEAR, OPTICAL 1 CLASS, FT IMPACT RESISTANCE; ANTI-UV99%, ANTI-FOG

DESIGN: CLASSIC STYLE, COMMON 3D FACIAL, SOFT SILICONE NOSE PADS, ADJUSTABLE LEG

CONFORM: BS EN 166/ANSI Z87.1/GB14866

PACKAGE: 1 PAIR / BAG, 300BAGS / CARTON

INDUSTRIAL

 

ITEM 028

SAFETY GLASSES

LENS: CLEAR, OPTICAL 1 CLASS, FT IMPACT RESISTANCE; ANTI-UV99%, ANTI-FOGDESIGN: STREAMLINE STYLE, COMMON 3D FACIAL, (OPTIONALLY EXCLUSIVE HEADBAND)

CONFORM: BS EN 166/ANSI Z87.1/GB14866

EXCLUSIVE PRIMOP-100 (CG5118100) HEADBANDPURE COTTON REPLACE LEG, 360°EXTREME OPERATING FOCUS ON THE FRONT

PACKAGE: 1 PAIR / BAG, 300BAGS / CARTON

INDUSTRIAL

 

ITEM 029

SAFETY GLASSES

LENS: CLEAR, OPTICAL 1 CLASS, FT IMPACT RESISTANCE; ANTI-UV99%, ANTI-FOG

DESIGN: CLASSIC STYLE, COMMON 3D FACIAL, SOFT SILICONE NOSE PADS, ADJUSTABLE LEG

CONFORM: BS EN 166/ANSI Z87.1/GB14866

PACKAGE: 1 PAIR / BAG, 300BAGS / CARTON

INDUSTRIAL

 

ITEM 030

DISPOSABLE MEDICAL NITRILE INSPECTION GLOVES (POWER-FREE)

SPECIFICATIONS: SKY BLUE, NITRILE MATERIAL, POWDER-FREE, NON STERILE, FOR DISPOSABLE MEDICAL EXAMINATION, UNIVERSAL FOR LEFT AND RIGHT HAND.

WATER IMPERVIOUS: G-1 /AQL 1.5

UNIT WEIGHT: 4.6G (SIZE M) LENGTH: 240mm

SIZE: S / M / LSHELF LIFE: 3 YEARS

STANDARD: GB10213-2006 "DISPOSABLE RUBBER INSPECTION GLOVES"

CERTIFICATION: ISO13485 MEDICAL DEVICE MANUFACTURER SYSTEM CERTIFICATION US FDA 510 (K)

SHIPPING: 20GP: 1380 CTN, 40GP: 2860 CTN, 40HQ: 3220 CTN

PACKAGE: 100 PCS / BOX, 10 BOXES / CARTON, 5.4 KG/ CARTON (SIZE S), 5.8 KG / CARTON (SIZE M) 6.3 KG / CARTON (SIZE L).

OUTER CARTON SIZE 340X250X250 mm

COLOR BOX SIZE 240X120X65 mm

MOQ: 500 PAIRS / CARTON

MEDICAL / INDUSTRIAL

 

ITEM 031

DISPOSABLE MEDICAL LATEX INSPECTION GLOVES (POWER-FREE)

SPECIFICATIONS: WHITE, NATURAL LATEX MATERIAL, POWDER-FREE, NON-STERILE, FOR DISPOSABLE MEDICAL EXAMINATION, UNIVERSAL FOR LEFT AND RIGHT HANDS

WATER-IMPERMEABLE: G-1 / AQL 1.5

SINGLE WEIGHT: 6.0G (SIZE M), LENGTH: 240mm

SIZE: S / M / L

SHELF LIFE: 3 YEARS

STANDARD: GB10213-2006 "DISPOSABLE RUBBER INSPECTION GLOVES"

CERTIFICATION: ISO13485 MEDICAL DEVICE MANUFACTURER SYSTEM CERTIFICATION US FDA 510 (K)

SHIPPING: 20GP: 1310 CTN, 40GP: 2727 CTN, 40HQ: 3015 CTN

PACKAGE: 100 PCS / BOX, 10 BOXES / CARTON 6.6 KG / CARTON (S) 7.1 KG / CARTON (M) 7.7 KG / CARTON (L)

OUTER CARTON SIZE: 365X250X245 mm

COLOR BOX SIZE 235X120X70 mm

MOQ: 500 PAIRS / CARTON

MEDICAL / INDUSTRIAL

 

ITEM 032

INFRARED THERMOMETER

MODEL: FJDT802

POWER SUPPLY: 9V

MEASURING RANGE: BODY MODE 32°C-42°C

MEASURING ACCURACY: INFRARED BODY 0.1-0.3°C, SURFACE±1.5%

MEASURING DISTANCE: INFRARED 3-50mm, SUFACEDISTANCE COEFFICIENT RADIO 12: 1

RESPONSE TIME: 0.8 SECOND

AUTO POWER-OFF: ≤ 15SECONDS RECORD DATA 32GROUPS

FEVER ALARM DIDI ALARM WHEN FEVER

TRANSPORTATION STORAGE: AMBIENT TEMPERATURE -20~55°C, RELATIVE HUMIDITH≤ 93%

WORKING ENVIRONMENT: AMBIENT TEMPERATURE 16~35°C, RELATIVE HUMIDITH≤ 85

 

FEATURES:

SIMPLE ONE-HANDED OPERATION

LASER TARGETING

LCD WITH BACK LIGHT°C/°F SELECT SWITCH

LASER ON/OFF SWITCH

AUTOMATIC POWER OFF

DISPLIAY HOLD FUNCTION

MEASURING: 50mm-150mm(2IN-5.9IN)

THE OPERATOR CAN BRING THIS INSTRUMENT AROUND WORK WITH CARRYING CASE WHICH CAN BE FIT ON THE BELT.

LED BACK LIGHT SYSTEM FOR OPERATION UNDER POOR LIIUMINATION.

 

PACKAGE: 40 PCS/CARTON

WEIGHT: 8.4KG

OUTER CARTON SIZE: 410 X 330 X 440mm
STANDARDS: CE

MEDICAL / INDUSTRIAL

 

ITEM 033

INFRARED THERMOMETER

OPERATING VOLTAGE: DC 3V

BATTERY MODEL: AAA X 2

BATTERY LIFE: ALKALINE DRY BATTERY FOR AROUND 20, 000 MEASUREMENTS

MEASURE TIME: ABOUT1~2 SECOND

MEASURING RANGE: FOREHEAD MODE: 32.0°C-42.9°C (89.6°F-109.2°F)

OBJECT MODE: 0.0°C-93.0°C (32.0°F-199.4°F)

ACCURACY(LABORATORY): ±0.2°C (±0.4°F)

MEMORY: 20 TEMPERATURE READINGS

LOW-BATTERY ALERT: THE LOW-BATTERY SYMBOL IS DISPLAYED IF THE POWERVOLTAGE IS LOWER THAN 2.5 V±0.1V

AUTOMATIC POWER-OFF: THE THERMOMETER AUTOMATICALLY POWERS OFF IF IT IS NOTUSED IN 8±1 SECONDS

OUTER DIMENSIONS(mm): 140X40X40mm

WEIGHT (G): (WITHOUT BATTERIES): 68G

OPERATING ENVIRONMENT: TEMPERATURE: 16°C~ 35°C (60.8°F-95°F)

HUMIDITY: 15%-95% RH, NON-CONDENSING

ATMOSPHERIC PRESSURE: 86-106 KPA

PACKAGE: 100 PCS/CARTON

PRODUCT PACKAGE SIZE: 1720 X650 X46mm

OUTER CARTON SIZE: 4900 X4000 X350mm

GROSS WEIGHT: 13KG

MEDICAL

 

ITEM 034

DISPOSABLE PPROTECTIVE MASK

MADEOF WHITE THREE-LAYER NON-WOVEN FABRIC.

STANDARD: T / CTCA 7-2019 "GENERAL PROTECTIVE MASK"

APPLICATION: SUITABLE FOR THE PROTECTION IN DAILY LIFE TO FILTER OUT POLLEN, BACTERIAL PARTICLES AND BLOCK OUT NASAL OR ORAL EXHALATION OR SPRAY POLLUTANT FACE MASK.

PACKAGE: 50 PCS / BAG, 60 PACKS / CARTON

CARTON SIZE: 700 X400 X400mm

WEIGHT: 12KG

STANDARDS: T/CTCA 72019

INDUSTRIAL

 

ITEM 035

DISPOSABLE PPROTECTIVE MASK

SIZE: 175 X 95mm

STANDARD: Q / AKKZ-001-2020

DISPOSABLE INDUSTRIAL MASK, TWO LAYERS OF NON-WOVENFABRIC, MIDDLE MELT-BLOWN FABRIC

APPLICATON: NON-MEDICAL, NEW INDUSTRIAL DISPOSABLE PROTECTIVE MASK FOR COVID-19

VALIDITY PERIOD: 1 YEAR

 

PACKAGE: 2000 PCS / CARTON

CARTOON SIZE: 530 X380 X340mm

WEIGHT: 10KG

STANDARDS: T/CTCA 72019 Q/AKKZ-001-2020

INDUSTRIAL

 

ITEM 036

DISPOSABLE THREE-DIMENSIONAL PROTECTIVE MASK (SIZE M)

NON WOVEN THREE-LAYER MASK

SIZE: 145mmX 90mm

MATERIAL: PP NON-WOVEN (SPUNBOND), MELT-BLOWN CLOTH FILTER LAYER

FEATURES: THREE LAYERS OF PROTECTION, MOISTURE-PROOFNON-WOVEN FABRIC ON THE OUTER LAYER, MELT-BLOWN FABRIC ON THE MIDDLE LAYER AND SKIN FRIENDLY NON-WOVEN FABRIC ON THE INNER LAYER; IT WAS EXPORTED TO JAPANESE PHARMACEUTICAL STORES.

 

APPLICATION: CHILDREN AND PEOPLE WITH SMALL FACE

 

PACKAGE: 50 PCS / BOX, 2000PCS / BOX

SIZE: 530mmX 380mmX 430mm

WEIGHT: 7.6KG

STANDARDS: CE GB/T32610-2016

INDUSTRIAL

 

ITEM 037

DISPOSABLE THREE-DIMENSIONA L PROTECTIVE MASK (SIZE L)

NON WOVEN THREE-LAYER MASK

SIZE: 175mmX 90mm

MATERIAL: PP NON-WOVEN (SPUNBOND), MELT BLOWN CLOTH FILTER LAYER

FEATURES: THREE LAYERS OF PROTECTION, MOISTURE-PROOF NON-WOVEN FABRIC ON THE OUTER LAYER, MELT-BLOWN FABRIC ON THE MIDDLE LAYER AND SKIN FRIENDLY NON-WOVEN FABRIC ON THE INNER LAYER; IT WAS EXPORTED TO JAPANESE PHARMACEUTICAL STORES.

 

APPLICATION: ADULTS

 

PACKAGE: 50 PCS / BOX, 2000PCS / BOX SIZE: 530mmX 440mmX 430mm

WEIGHT: 8KG

STANDARDS: CE GB/T32610-2016

INDUSTRIAL

 

ITEM 038

KN95 PROTECTIVE MASK

MATERIAL: PP NON-WOVEN FABRIC, FILTER MATERIAL, EAR BAND, NOSE BRIDGE

FEATURES: FIVE LAYERS OF PROTECTION PROVIDES HIGH EFFICIENCY FILTERING; ADJUSTABLE NOSE BRIDGE TOFIT THE FACE; WIDENED ELASTIC COTTON ROPE, WHICH CAN BE EASILY PULLED WITHOUT TENSION.

 

APPLICATION: ADULTS

 

PACKAGE: 50PCS / BOX, 2000PCS / CARTON

CARTON SIZE: 600 X 600 X 570mm

WEIGHT: 17KGMOQ:2,000PCS/CTN

STANDARDS: CE GB2626-2006 FDA

INDUSTRIAL

 

ITEM 039

N95 PROTECTIVE MASK

N95 GB19083-2010

PACKAGE: 1PC / BAG, 350 PCS / CARTON

CARTON SIZE: 520 X 480 X 300mm

WEIGHT: 7KG

MOQ: 500,000PCS

STANDARDS: CE GB19083-2010

MEDICAL / INDUSTRIAL

Learn More