Search results for: 'ventilator'

NON-INVASIVE VENTILATOR
CERTIFICATE: CE
MEDICAL VENTILATOR
TECHNICAL PARAMETERS OF DOUBLE LEVEL VENTILATOR
VENTILATOR TYPE: ELECTRIC CONTROL
SCOPE OF APPLICATION: TREATMENT AND TITRATION OF SLEEP APNEA HYPOPNEA SYNDROME, SEVERE SNORING, AND RESPIRATORY INSUFFICIENCY.
DISPLAY INTERFACE: 3.5-INCH LED SCREEN, CHINESE OPERATING SYSTEM
*VENTILATION MODE: CPAP, S, S/T, T
PRESSURE RANGE:
PRESSURE RANGE: 4-30CMH2O (±0.5CMH2O)
PRESSURE ACCURACY: + 0.5CMH2O
PARAMETER SETTING:
DELAYED BOOST: 0-60MIN, SET THE DIVISION INTERVAL 5MIN
INITIAL PRESSURE: 4CMH2O TREATMENT PRESSURE / RESPIRATORY PRESSURE SETTING
THERAPEUTIC PRESSURE: 4-20CMH2O (IN CPAP MODE)
TARGET TIDAL VOLUME: 150ML - 1500ML, ON/ OFF
MAXIMUM SUCTION PRESSURE: 4-30CMH2O, (CAN BE SET WHEN THE TARGET TIDAL VOLUME FUNCTION IS ON)
MINIMUM SUCTION PRESSURE: 4-30CMH2O (NOT HIGHER THAN THE SUCTION PRESSURE), (CAN BE SET WHEN THE TARGET TIDAL VOLUME FUNCTION IS ON)
INSPIRATORY PHASE PRESSURE: 4-30CMH2O
EXPIRATORY PRESSURE: 4-30CMH2O
EXPIRATORY DECOMPRESSION: PATIENT, OFF, 1-3, THREE ADJUSTABLE
MANUAL VOLTAGE REGULATION: 0-2 GEAR, 0-2CMH2O (ONLY AVAILABLE IN CPAP MODE)
INSPIRATORY SENSITIVITY: 1-8 STALLS
EXPIRATORY SENSITIVITY: 1-8 STALLS
RESPIRATORY FREQUENCY: 3-40 TIMES / MIN
INSPIRATORY TIME: 0.3-3.0S
BACKUP RATE: ON / OFF, DEFAULT 10
PRESSURE RISE TIME: 1-4 STALLS
HUMIDIFIER: 1-5 ADJUSTABLE IN 5 GEARS
*TITRATION FUNCTION: SUPPORT MANUAL AND AUTOMATIC PRESSURE TITRATION, BUILT-IN REMOTE WIRELESS COMMUNICATION MODULE, COMPLETE THE RANDOM SWITCHING OF SINGLE AND DOUBLE LEVEL MODES IN THE TITRATION PROCESS, AND CONTROL MORE THAN 11 VENTILATOR PARAMETERS AT THE SAME TIME.
AUXILIARY FUNCTION: AUTOMATIC AIR LEAKAGE COMPENSATION, AUTOMATIC STARTUP, AUTOMATIC SHUTDOWN, DELAYED SHUTDOWN, SCREEN BACKLIGHT ADJUSTMENT
MONITORING PARAMETERS: PRESSURE, TIDAL VOLUME, RESPIRATORY RATE, MINUTE VENTILATION VOLUME, AIR LEAKAGE VOLUME, INSPIRATORY TIME, BLOOD OXYGEN SATURATION
WAVY CURVE: PRESSURE TIME WAVEFORM, FLOW RATE TIME WAVEFORM
ALARM PROMPT: PIPELINE AND MASK FALLING OFF, AIR LEAKAGE PROMPT, POWER INTERRUPTION, TREATMENT MACHINE FAILURE, HUMIDIFIER FAILURE, LOW VOLTAGE, HIGH RESPIRATORY RATE, LOW RESPIRATORY RATE, LOW MINUTE VENTILATION VOLUME, LOW BLOOD OXYGEN, REPLACEMENT OF FILTER COTTON, FULL SD CARD, RE INSERTION OF SD CARD
*DATA MANAGEMENT:
NETWORK DATA: BMC + RESPIRATORY HEALTH MANAGEMENT CLOUD PLATFORM
SD CARD DATA: RESART NPAP DATA ANALYSIS SOFTWARE
PARTS:
SD CARD: STANDARD
SD CARD SLOT: STANDARD
PIPING: 9 22MM, 1.8M LONG
FACE SHIELD: F2 NOSE MASK AS STANDARD
NOISE: LESS THAN 30DB
ENVIRONMENT CONDITION:
TEMPERATURE:
(WHEN USED) 5 -35 C
(DURING TRANSPORTATION AND STORAGE) -20 C -55 C
ATMOSPHERIC PRESSURE:
(WHEN USED) 760-1060HPA
(DURING TRANSPORTATION AND STORAGE) 760-1060HPA
WORKING HOURS: MORE THAN 8 HOURS
POWER SUPPLY REQUIREMENTS:
AC VOLTAGE: 100-240V
FREQUENCY: 50HZ/60HZ
INPUT POWER: LESS THAN 2A
WATERPROOF LEVEL: IP22 - DRIP PROOF EQUIPMENT
INSTRUMENT SIZE: 290mm X 180mm X 134mm
WEIGHT: 1.5KG (EXCLUDING HUMIDIFIER) 2.5KG (INCLUDING HUMIDIFIER)
ITEM 001
QUANTITY: 10 SETS-999 SETS
ITEM 002
QUANTITY: 1,000 SETS-9,999SETS
ITEM 003
QUANTITY: ≥10,000 SETS

Learn More

INVENTORY NUMBER: E-6016 TRUTZSCHLER PREPARATION LINE FOR COTTON FIBERS YEAR 2003 FOR SALE AS A COMPLETE PLANT ONLY TRUTZSCHLER COTTON PROCESSING MACHINE, C/O, MODEL SC 1552002 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION DETAILS: MAIN FEATURES: - THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS; - HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS; - CONVEYOR WIDTH: 2200mm; - WORKING WIDTH: 2000mm; - MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C; - HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW; - VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS; - ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS; - INSTALLED ELECTRIC POWER: 200 KW. APPROX.; - MECHANICAL SPEED: 2÷15 METERS PER MINUTE; - CONVEYOR DRIVING: BY A.C. MOTORS; - MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More

REFERENCE NUMBER: G-8444 PUNCHING MACHINE MODEL FST 11 MACHINE AVAILABLE FOR AUTOMATIC DRILLING IN SHEETS OF PU FOAM, MEMORY FOAM, LATEX, EVA, NEOPRENE. WITH 20mm THICKNESS UP 2 DRILLINGS PER SECOND ARE PERFORMED; E.G.: ONE MOULD FOR 2mm DIAM. HOLES AND 50mm WHEEL BASE OF PUNCH, 7mm X 3.5 CROSSED HOLE PITCH: THE MACHINE WILL PERFORM NO 2310 HOLES EACH DRILLING CYCLE WITH 4620 HOLES PER SECOND IN TOTAL. THAT MEANS THE MACHINE CAN DRILL A FOAM SHEET DIM. 1000X1100mm EACH 20 SECONDS WITH 92400 HOLES IN TOTAL. TWO DRILLING TYPES ARE POSSIBLE: CONTINUOUS DRILLING “A-PERFORM” (NO DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS –SEE TAB. 31A); CONTINUOUS DRILLING “B-PERFORM” (WITH FIXED DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS). THE DISTANCE CAN BE MODIFIED BY OPERATOR). UP TO 150 20mm-THICKNESS MATTRESSES CAN BE PRODUCED IN ONE HOUR; BY INCREASING THE THICKNESS THE PRODUCTION WILL REDUCE. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-8444-A PUNCHING MACHINE MODEL FST 11 FOR LATEX MACHINE AVAILABLE FOR AUTOMATIC DRILLING IN SHEETS OF PU FOAM, MEMORY FOAM, LATEX, EVA, NEOPRENE. WITH 20mm THICKNESS UP 2 DRILLINGS PER SECOND ARE PERFORMED; E.G.: ONE MOULD FOR 2mm DIAM. HOLES AND 50mm WHEEL BASE OF PUNCH, 7mm X 3.5 CROSSED HOLE PITCH: THE MACHINE WILL PERFORM NO 2310 HOLES EACH DRILLING CYCLE WITH 4620 HOLES PER SECOND IN TOTAL. THAT MEANS THE MACHINE CAN DRILL A FOAM SHEET DIM. 1000X1100mm EACH 20 SECONDS WITH 92400 HOLES IN TOTAL. TWO DRILLING TYPES ARE POSSIBLE: CONTINUOUS DRILLING “A-PERFORM” (NO DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS –SEE TAB. 31A); CONTINUOUS DRILLING “B-PERFORM” (WITH FIXED DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS). THE DISTANCE CAN BE MODIFIED BY OPERATOR). UP TO 150 20mm-THICKNESS MATTRESSES CAN BE PRODUCED IN ONE HOUR; BY INCREASING THE THICKNESS THE PRODUCTION WILL REDUCE. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4749 (1111ASRPXX10) L RECYCLING PLANT FOR FABRIC CUTTING (1) X MONDEJAR CUTTING MACHINE MODEL CUTTEX 1000, YEAR 1992 (1) X CHUTE FEED FOR ACCUMULATION MATERIAL WITH VENTILATOR (1) X ROLANDO BIELLA ITALY TEARING MACHINE YEAR 1973, NR.6 DRUMS (PLUS 1 SPARE) WORKING WIDTH 1000mm AND ELECTRICAL PANEL COMPLETE WITH 1 ENZIMAGE (1) LLORPIC AUTOMATIC VERTICAL PRESS MODEL ALCOY, YEAR 1994 WITH CHUTE FEED FOR ACCUMULATION MATERIAL VENTILATOR AND ELECTRICAL BOX (4) X BONINO CARDS MODEL CC150/170 YEAR 1992, WITH BRIEST AND FIX FLATS BONINO CHUTE FEED (LIKE FBK533) EXIT CAN 40” X 48” WITH AUTOMATIC CHANGER QUANTITY AVAILABLE: 1 Learn More

J-5381 MACHINE TO PRODUCE PILLOW FILLING OF POE/EVA TO FILL PILLOWS WITH POE/EVA WITH DENSITY 20 TO 90 DENSITY (KGS/CUBIC METER) WITH THICKNESS BETWEEN 10mm AND 200mm QUANTITY: 1 Learn More

TT-7505 BIANCO/CORINO/MARIO CROSTA/GUIDO/ALEA/SPEROTTO RIMAR/TMT/BISIO/SOC.AN.COMI/F.REGIS/KARL MAYER/ROSTONI/COMAT/SAVIO ESPERO MACHINES FOR SALE, YEAR 1986 TO 2006 Learn More

TT-4121 SAMPLE WARPING, WARPING AND FINISHING MACHINES, WIDTH 1800mm TO 2500mm, YEAR 1986 TO 2006 Learn More

T-9509 MENZEL COATING RANGE, WORKING WIDTH 2600mm, 35 METERS PER MINUTE GENERAL DESCRIPTION: DIFFERENT METHODS OF PRODUCTION CAN BE REALIZED, MACHINE IS DESIGNED FOR COATING ON A PRECISELY HIGH COATING ROLLER OR AS AN AIR DOCTOR BLADE. EQUIPPED WITH A COLLISION CONTROL SYSTEM AVAILABLE IMMEDIATELY Learn More