Search results for: 'Full in'

P-8910 LIFTBOY VERTICAL PLATFORM LIFT THE LIFT CAN BE EQUIPPED WITH SPECIAL SIDE ENTRY OR EXIT, UPPER CASE GATE OR TRANSPORT WHEELS QUANTITY: 1 Learn More

T-6968 JENBACHER J626 GS-H102 4400KW 50Hz 10500V-SURPLUS NEW, YEAR 2018 QUANTITY: 2 Learn More

REFERENCE NUMBER: Y-2076 TEMPERATURE AND HUMIDITY TEST CHAMBER THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS. IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE. ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS. SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES. THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME. THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER. DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED. VOLUME DIMENSION: ABOUT 150L INTERIOR SIZE: W: 600mm H: 600mm D: 460mm THE MAIN TECHNICAL PARAMETERS TEST CONDITION COOL METHOD: AIR COOLED MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS. THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃ TEMPERATURE FLUCTUATION ± 0.5 ℃ TEMPERATURE UNIFORMITY: ≤ 2.0 ℃ TEMPERATURE DEVIATION: ≤ ± 2.0 ℃ TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃ FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD) COOLING RATE: +20 ℃ TO 40 ℃ FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD) QUANTITY: 1 Learn More

REFERENCE NUMBER: A-2478 ADVANCED LEVEL SINGLE NOZZLE ELECTROSPINNING UNIT - STATIONARY PLATE COLLECTOR THIS ELECTROSPINNING UNIT IS A MODEL IN BETWEEN BASIC AND ADVANCED ELECTROSPINNING SYSTEMS. ALL PROCESS PARAMETERS CAN BE ADJUSTED FROM ITS PROGRAMMABLE EASY-TO-USE TOUCH SCREEN PANEL. IT ALSO HAS A SPECIAL DESIGNED ISOLATED CHASSIS AND AN EXHAUST SYSTEM THAT ENABLES WORKING WITH EVAPORATIVE SOLVENTS. THANKS TO THE ADVANCED SAFETY FEATURES, THE DOOR SAFETY SYSTEM AND THE ISOLATED CHASSIS, SCIENTISTS CAN CARRY OUT THEIR EXPERIMENTS IN SAFE CONDITIONS, WITHOUT WORRYING ABOUT ANY RISK OF USERS’ HEALTH ENDANGERMENT. SPECIFICATIONS: SPINNING-TYPE: BOTTOM-UP SPINNING CHASSIS: ELECTROSTATICALLY PAINTED STEEL FEEDING AREA MATERIAL: PE 1000 (HIGH DENSITY, CHEMICAL RESISTANT) COLLECTOR MATERIAL: 7000 SERIES ALUMINUM ALLOY, STAINLESS STEEL LED ILLUMINATION EXHAUST FAN ATMOSPHERE CONTROL (OPTIONAL) TOTAL WEIGHT: APPROX.150 KGS DIMENSIONS: 770 X 675 X 1040 mm HIGH VOLTAGE POWER SUPPLY VOLTAGE RANGE: 0 TO 40 KV VOLTAGE PRECISION: 0.1 KV MAX CURRENT: 0.125 MA HIGH PRECISION MICRO PUMP FLOW RATE: 0.01 TO 4464 ML/H (BD 60 ML SYRINGE) FLOW RATE PRECISION: 0.01 ML/H AVAILABLE SYRINGES STANDARD: ALL TYPES ARE AVAILABLE FEEDING AREA NUMBER OF NOZZLES: 1 NOZZLE NOZZLE INNER DIAMETER: 0.8 mm COMPATIBLE WITH STANDARD SYRINGE NOZZLES MINIMUM REQUIRED SOLUTION FOR SINGLE NOZZLE FEEDING: 2 ML SPINNING DISTANCE DISTANCE BETWEEN NOZZLE AND COLLECTOR: 13 TO 213 mm DISTANCE ADJUSTMENT PRECISION: 1 mm STATIONARY PLATE COLLECTOR MATERIAL: STAINLESS STEEL DIMENSIONS OF STATIONARY PLATE: 370 X 130 mm UNIQUE USER INTERFACE 9" TOUCH SCREEN CONTROL PANEL WITH WELL DESIGNED USER FRIENDLY INTERFACE FULLY ABLE TO CONTROL ALL PARAMETERS SAVING & RECALLING ALL PARAMETERS VIA RECIPE & RECALL FUNCTION SAFETY FUNCTION SAFE DOOR EMERGENCY BUTTON & SAFETY RELAY HV WARNING LIGHT ELECTRICAL ISOLATED & GROUNDED CABINET OVER CURRENT PROTECTION FULLY SEALED CABINET TECHNICAL REQUIREMENTS POWER: 220 VOLTS AND 50/60 HZ @ MAX 25A GROUNDING: EXTERNAL GROUNDING LINE AREA: MIN. 1000 X 1000 mm WORKBENCH ABLE TO CARRY MINIMUM 150 KGS. Learn More

REFERENCE NUMBER: A-2477 ADVANCED LEVEL SINGLE NOZZLE ELECTROSPINNING UNIT - DRUM COLLECTOR MACHINE IS A LABORATORY SCALE ELECTROSPINNING UNIT WITH A SINGLE NOZZLE. THE STANDARD MACHINES HAVE A 500 RPM ROTATING DRUM COLLECTOR AND A FLAT COLLECTOR. THERE ARE OPTIONAL ACCESSORIES UPON REQUEST FOR FUNCTIONALITY IMPROVEMENT. OPERATION PARAMETERS LIKE THE NEEDLE-COLLECTOR DISTANCE AND HIGH VOLTAGE VALUE COULD BE AUTOMATICALLY ADJUSTED FROM THE USER PANEL, WITH HIGH PRECISION. THE SYSTEM COMES WITH AN ENCLOSED CABINET MAKING IT POSSIBLE TO ADD TEMPERATURE AND RELATIVE HUMIDITY CONTROL SYSTEMS. SPECIFICATIONS: SPINNING-TYPE: BOTTOM-UP SPINNING CHASSIS: ELECTROSTATICALLY PAINTED STEEL FEEDING AREA MATERIAL: PE 1000 (HIGH DENSITY, CHEMICAL RESISTANT) COLLECTOR MATERIAL: 7000 SERIES ALUMINUM ALLOY, STAINLESS STEEL LED ILLUMINATION EXHAUST FAN ATMOSPHERE CONTROL (OPTIONAL) TOTAL WEIGHT: APPROX.150 KGS DIMENSIONS: 770 X 675 X 1040 mm HIGH VOLTAGE POWER SUPPLY VOLTAGE RANGE: 0 TO 40 KV VOLTAGE PRECISION: 0.1 KV MAX CURRENT: 0.125 MA HIGH PRECISION MICRO PUMP FLOW RATE: 0.01 TO 4464 ML/H (BD 60 ML SYRINGE) FLOW RATE PRECISION: 0.01 ML/H AVAILABLE SYRINGES STANDARD: ALL TYPES ARE AVAILABLE FEEDING AREA NUMBER OF NOZZLES: 1 NOZZLE NOZZLE MATERIAL: ELECTRICALLY CONDUCTIVE STAINLESS STEEL NOZZLE INNER DIAMETER: 0.8 mm COMPATIBLE WITH STANDARD SYRINGE NOZZLES MINIMUM REQUIRED SOLUTION FOR SINGLE NOZZLE FEEDING: 2 ML SPINNING DISTANCE DISTANCE BETWEEN NOZZLE AND COLLECTOR: 33.5 TO 233.5 mm DISTANCE ADJUSTMENT PRECISION: 1 mm ROTATING COLLECTOR DRUM COLLECTOR MATERIAL: ALUMINUM DIMENSIONS OF DRUM: 100 X 150 mm FIBER DEPOSITION AREA: 314 X 150 mm DRUM ROTATING SPEED: 100 TO 500 RPM SURFACE SPEED: 52.3 CM/S TO 261.6 CM/S STATIONARY PLATE COLLECTOR MATERIAL: STAINLESS STEEL DIMENSIONS OF STATIONARY PLATE: 370 X 130 mm UNIQUE USER INTERFACE 9" TOUCH SCREEN CONTROL PANEL WITH WELL DESIGNED USER FRIENDLY INTERFACE FULLY ABLE TO CONTROL ALL PARAMETERS SAVING & RECALLING ALL PARAMETERS VIA RECIPE & RECALL FUNCTION SAFETY FUNCTION SAFE DOOR EMERGENCY BUTTON & SAFETY RELAY HV WARNING LIGHT ELECTRICAL ISOLATED & GROUNDED CABINET OVER CURRENT PROTECTION FULLY SEALED CABINET TECHNICAL REQUIREMENTS POWER: 220 VOLTS AND 50/60 HZ @ MAX 25A GROUNDING: EXTERNAL GROUNDING LINE AREA: MIN. 1000 X 1000 mm WORKBENCH ABLE TO CARRY MINIMUM 150 KGS. Learn More

REFERENCE NUMBER: T-6543

MEDICAL UNIVERSAL TENSILE TESTING EQUIPMENT

 

SHANDONG INDEPENDENTLY RESEARCH AND DEVELOPMENT THIS COMPREHENSIVE TESTING MACHINE FOR SURGICAL MASK & PROTECTIVE CLOTHING, IT IS WIDELY USED IN A VARIETY OF MASK STRENGTH DETECTION PROJECTS.FEATURES:COMPLY WITH NATIONAL STANDARDS, MEDICAL STANDARDS TESTING REQUIREMENTS, AUTOMATIC SOFTWARE CONTROL SYSTEM, MEET THE REQUIREMENTS OF DATA STORAGE, PRINTING, COMPARISON. THE IMPORTED SERVO MOTOR IS EQUIPPED WITH PRECISION SCREW DRIVE SYSTEM TO ENSURE THE STABILITY OF TEST DATA.

 

TEST STANDARDS:

GB 19082-2009 TECHNICAL REQUIREMENTS FOR DISPOSABLE PROTECTIVE CLOTHING FOR MEDICAL USE (4.5 BREAKING STRENGTH -THE BREAKING STRENGTH OF MATERIALS IN KEY PARTS OF PROTECTIVE CLOTHING SHOULD NOT BE LESS THAN 45N)

(4.6 ELONGATION AT BREAK -THE ELONGATION AT BREAK OF KEY PARTS OF PROTECTIVE CLOTHING SHOULD NOT BE LESS THAN 15%)

SELF-PRIMING FILTER RESPIRATOR FOR RESPIRATORY PROTECTION ARTICLES5.6.2 BREATHING BONNET -BREATHING BONNET SHALL BE SUBJECT TO AXIAL TENSION"DISPOSABLE MASK: 10N FOR 10S" "REPLACEABLE MASK: 50N FOR 10S"

(5.9 HEADBAND -HEADBAND SHOULD BEAR THE TENSION "DISPOSABLE MASK: 10N, 10S" "REPLACEABLE HALF MASK: 50N FOR 10S" "FULL MASK: 150N FOR 10S")

5.10 JOINTS AND CONNECTING PARTS -JOINTS AND CONNECTING PARTS SHALL BE SUBJECT TO AXIAL TENSION

"REPLACEABLE HALF MASK: 50N FOR 10S" "FULL COVER 250N FOR 10S"

GB/T 32610-2016 TECHNICAL SPECIFICATION FOR DAILY PROTECTIVE MASKS

(6.9 BREAKING STRENGTH OF THE MASK BELT AND THE CONNECTION BETWEEN THE MASK BELT ANDTHE MASK BODY ≥ 20N)

(6.10 FASTNESS TO BREATHING BONNET: NO SLIPPAGE, BREAKAGE OR DEFORMATION SHALL OCCUR)

YY/T 0699-2013 DISPOSABLE SURGICAL MASK

(4.4 MASK BELT -THE BREAKING FORCE AT THE CONNECTION POINT BETWEEN EACH MASK BELT AND THE MASK BODY IS NOT LESS THAN 10N)

YY 0469-2011 SURGICAL MASK FOR MEDICAL USE (5.4.2 MASK BELT)

GB/T 3923.1-1997 DETERMINATION OF BREAKING STRENGTH AND ELONGATION AT BREAK OF FABRICS (STRIP METHOD)

DISPOSABLE RUBBER INSPECTION GLOVES (6.3 TENSILE PROPERTIES)

 

INSTRUMENT TECHNICAL PARAMETERS:

SPECIFICATION: 200N (STANDARD) 50N, 100N, 500N, 1000N (OPTIONAL)

ACCURACY: BETTER THAN 0.5RESOLUTION OF FORCE VALUE: 0.1N

DEFORMATION RESOLUTION: 0.001mm

TEST SPEED: 0.01mm/MIN ~ 2000mm/MIN (STEPLESS SPEED REGULATION)

WIDTH OF SAMPLE: 30mm (STANDARD FIXTURE) 50mm (OPTIONAL FIXTURE)

CLAMPING OF SAMPLES: MANUAL (PNEUMATIC CLAMPING CAN BE CHANGED)

STROKE: 700mm (STANDARD) 400mm, 1000mm (OPTIONAL)

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

 

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

Learn More

K-8158 COAL FIRED STEAM POWER PLANT 330 MW YEAR 1983

COAL FIRED STEAM POWER PLANT 330 MW
PLANT FOR RELOCATION
EQUIPMENT AND AUXILIARIES IN EXCELLENT CONDITION

SUMMARY OF MAIN ADVANTAGES:
THE STEAM PLANT IS AVAILABLE NOW AND CAN BE REINSTALLED IN SHORT TIME
POWER AVAILABLE IN SHORT TIME
THE EQUIPMENT IS OFFERED AT ATTRACTIVE CONDITIONS
LOW INVESTMENT COST
THE MAIN EQUIPMENT IS BASED ON STATE OF THE ART DESIGN & EMISSION CONTROL
COMMERCIAL LIFE TIME FOR MANY YEARS TO COME
RELOCATION IN COOPERATION WITH OEM SUPERVISING AND GUARANTEES OVERALL CONCEPT

TECHNICAL DATA OF BOILER:
OEM
STEAM OUTPUT DESIGN PRESSURE LIVE STEAM REHEAT TEMP FUEL

980 T/H
203 BAR
184 BAR / GRAD C

BROWN COAL, APPROXIMATELY 9,000 KJ/KG
HARD COAL POSSIBLE AS WELL (24,000 - 28,000 KJ/KG)

CONSUMPTION APPROXIMATELY 280 T/H AT FULL LOAD WITH BROWN COAL
APPROXIMATELY 110 T/H AT FULL LOAD WITH HARD COAL

GRINDING MILLS: 6

EMISSION SO2 200 MG/NM3 X 200 MG/NM3 ASHES 50 MG/NM3 EXHAUST TEMP 70°C

TECHNICAL DATA STEAM TURBINE:
OEM
OUTPUT
LIVE STEAM: 330/345 MW, 177.5 BAR, 535°C

GENERAL REMARKS:
PLANT HAS GONE IN COMMERCIAL OPERATION IN 1983
PLANT AND EQUIPMENT HAS BEEN IN OPERATION BASICALLY DURING THE WINTER PERIOD AND HAS 84,300 HOURS ACCUMULATED ONLY
ALL EQUIPMENT IS IN EXCELLENT CONDITION AND PROFESSIONALLY PRESERVED

ENTIRE PLANT WITH ALL AUXILIARIES IS AVAILABLE FOR RELOCATION

SCOPE AND CONDITIONS:
DISASSEMBLED, PACKED, AND SHIPPED OR TURNKEY SOLUTION CAN BE NEGOTIATED
RELOCATION WILL BE INCOORDINATION WITH THE OEM WHO IS WILLING TO GIVE A CERTAIN LEVEL OF GUARANTEE FOR THE RELOCATED PLANT

QUANTITY: 1

Learn More

REFERENCE NUMBER: C-3851

MONFORTS STENTER FOR KNITS

MODEL: MONTEX 6500 7F TWINAIR

7 CHAMBERS GAS HEATED

WORKING WIDTH: 2200mm

YEAR: 2012

 QUANTITY: 1

Learn More

REFERENCE NUMBER: K-5014 HOTMELT GLUING MATTRESS PRODUCTION LINE 2200mm 1000 MATTRESSES PER 8-HOUR SHIFT MAXIMUM WIDTH: 2200mm CAPACITY: 1,000 MATTRESSES PER 8-HOUR SHIFT 1ST BRIDGE: 3 PNEUMATICALLY MOVING GUNS WITH 4 NOZZLES ON EACH HOTMELT GUN. CAN BE CONVERTED TO SPRAY AT NO EXTRA COST. 2ND BRIDGE: 2 GUNS FOR THE EDGE: ONE HAS 8 NOZZLES (T-SHAPED), THE OTHER HAS 4 NOZZLES. 3RD BRIDGE: 3 PNEUMATICALLY MOVING GUNS. THEY ARE SPRAY; LINE NOZZLES CAN BE ADDED 4TH BRIDGE: EXACTLY THE SAME AS 3RD BRIDGE. FLOORSPACE DIMENSIONS: 72000mm X 13000mm QUANTITY AVAILABLE: 1 Learn More