Search results for: 'Winder machine s'

REFERENCE NUMBER: M-0461 COMPLETE COMBED COTTON RING SPINNING MILL -10,560 SPINDLES -YEAR 1993 QUANTITY AVIAILABLE: 1 Learn More

REFERENCE NUMBER: M-3995 (88032BRV8RC) K SOFT CONE WINDER SAVIO ESPERO RL YEAR 1998 - 48 HEADS SOFT CONE WINDER "SAVIO ESPERO R.L." MACHINE WITH 48 HEADS YEAR 1998 SUITABLE FOR NORMAL CONES AND CONES FOR DYEING FOR SYNTHETIC/MIX AND COTTON YARN WAXING DEVICE IS MOUNTED ON EACH WINDING POSITION SPLICER ARE AVAILABLE ON 12 WINDING POSITIONS. IT'S MESDAN, TYP 492 AND 36 WINDING POSITIONS ARE WITH KNOTTER, MESDAN, TAPY 410 CAN CONFIRM THAT THE MACHINE HAS AUTO DOFFING YARN COUNT IS: SINGLE YARN: NE 20/1 - 100/1, TWISTED YARN: 20/2 - 170/2 UP TO 900 RPM. QUANTITY AVAILABLE: 1 Learn More

TT-5170 SCHONHERR ALPHA 360, WORKING WIDTH 4000mm, YEAR 2004, JACQUARD SCHONHERR ALPHA 360 WORKING WIDTH: 4000mm PRODUCTION YEAR: 2004 BRAND: SCHONHERR MODEL: ALPHA 360 STATE: USED Learn More

TT-2963 SSM ELECTRONIC ASSEMBLY WINDER WITH 20 HEADS, YEAR 1999 SSM ELECTRONIC ASSEMBLY WINDER MODEL DP W WITH 20 HEADS QUANTITY: 1 Learn More

TT-2138 LAROCHE / THIBEAU / ASSELIN / ICBT / FLEISSNER/ SPUNLACE / JETLACE / HYDROENTANGLEMENT LINES, YEAR 2000 Learn More

T-9752 KARL MAYER CARBON MACHINES BIAXIAL AND MULTIAXIAL PROPERTIES: SINCE ALL FIBERS POINT IN ONE DIRECTION, THE SCRIM CAN BE IDEALLY DRAPED GOOD SOAKABILITY WITH LITTLE RESIN CONSUMPTION CAN BE DRAPED VERY WELL AROUND CURVES AND EDGES EASY TO CUT ELECTRICALLY CONDUCTIVE, INFUSIBLE HIGH STRENGTH AND RIGIDITY DUE TO GRAPHITE-LIKE FIBER STRUCTURE BIOCOMPATIBLE TRANSPARENT TO X-RAYS LOW SPECIFIC WEIGHT IDEAL FOR SURFACE USE (LITTLE FIBER IMPRINTS) IDEAL FOR PROCESSING WITH EPOXY RESIN! TEXTILE SEMI-FINISHED PRODUCTS MADE OF PRE-SPREAD AND PLANE-PARALLEL LAID FIBERS FORM THE GROUP OF UNIDIRECTIONAL FABRICS. THE FIBERS ARE USUALLY LAID AT 0°, MORE RARELY AT 90°. BY LAYING THE UD FABRICS ALONG THE LINES OF FORCE ACTING IN THE COMPONENT, THE LIGHTWEIGHT POTENTIAL OF THE CARBON FIBER IS OPTIMALLY EXPLOITED. UD FABRICS CONSIST OF ONE OR MORE SUPERIMPOSED FIBER LAYERS FIXED WITH AN EPOXY-COMPATIBLE BINDER THREAD. THE SPECIAL SPREADING TECHNIQUE PRODUCES FABRICS WITH HIGH FIBER PARALLELISM, WITHOUT KNOTS AND FIBER TWIST. SPREAD FIBERS ABSORB THE RESIN BETTER, RESULTING IN HIGHEST LAMINATE STRENGTHS. QUANTITY: 3 LINES Learn More

REFERENCE NUMBER: C-1147 CARD WIRE WINDERS E.F, WIDTH 2500MM SPECIFICATIONS: CARD WIRE WINDERS E.F 2500 MM WORKING WIDTH WITH 2 VERTICAL AXLES WITH CHAIN DRIVEN TRANSPORTS, CYLINDER WITH MOTOR AND FREQUENCY VARIATOR 1 MACHINE WITH 14 SPINDLES 1 MACHINE WITH 11 SPINDLES QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: K-9424 MURATA 377 FTO & MURATA 607 WINDER MURATA 377 FTO YEAR: 1995-1997 QUANTITY: 2 MURATA 607 ASSEMBLING WINDER YEAR: 1995 QUANTITY: 2 QUANTITY AVAILABLE: 4 Learn More

REFERENCE NUMBER: M-1758 (6602BHBBE5U) GEOTEXTILE CALENDER MACHINE -5700mm- YEAR 2004 MAKE: BOMBI MECCANICA ITALY 5.7 M WIDE GEOTEXTILE CALENDER MACHINE YEAR: 2004 IS IN PERFECT CONDITION FEW HOUR PRODUCTION IT IS CONNECTED AND CAN BE SHOWN TO CUSTOMERS VOLTAGE: 440V / 60 HZ / 3 PHASES UNWINDER ACCUMULATORS WITH ROLLS, 50M OF CONTENT 2 ROLLS CALENDER 5.7 WIDE 200,000 KCAL/HR GAS OIL HEATER UPPER HOOD FOR THE SMOKE COLLECT METAL DETECTOR INSTALLED ON TOP OF CALENDER ADJUSTING 2 ROLLS TEMPERATURE INDEP. ACCUMULATORS WITH ROLLS, 50 M LONG CROSS CUTTER W/6 LONG SLITTERS, AND EXIT BELT WINDER OPTION ROLL DISCHARGER 2.3 M WINDER, SPEED UP TO 30 M/MIN, READY TO BE SYNCHRONIZED 2.3 M WIDE, EDGE TRIMMERS WITH 2 DISC BLADES FELT WIDTH: 5.5 METER WEB THICKNESS AT ENTRY: AROUND 1 TO 2 mm WEB PREPARATION AT THE INLET: CROSS LAPPING AND NEEDLING PRODUCTION LINE SPEED: UP TO 25 M/MIN TYPE OF TREATMENT: HEAT SETTING, SMOOTHING OF THE SURFACES AND CALIBRATION, CUTTING AND ROLLING UP FELT WEIGHT: 90 TO 300 GSM FIBERS: POLY COTTON BLEND, POLYESTER, ACRYLIC, POLYPROP THERMOSETTING TEMEPRATURE: UP TO 225°C QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More