Search results for: 'loop loop'

REFERENCE NUMBER: K-3941

LABORATORY COTTON FANCY YARN TWISTER

               

TWO SETS OF THICK YARN FEEDING, WITH CORN YARN ROLLER, TO SPIN COTTON LOOP YARN, SLUB/KNOP YARN, 2 COLOR FANCY YARN

               

CONTROL:TOUCH SCREEN+ PLC

4 SPINDLES

TWISTING DEGREE:ABOUT 200-2000 TIMES/METER

DRAFTING RANGE:ABOUT 2-50

FIBER LENGTH:22mm TO 42mm

OUTPUT:ABOUT 0.25KG-0.5KG

SPINDLE SPEED:12000 RPM

ROLLER SIZE:Φ25/25/25mm

RING SIZE:Φ38-45 mm

TOTAL POWER:750W

VOLTAGE:220/3×380V AC  50/60Hz

MACHINE DIMENSIONS 1000mm×800mm×1600mm

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: A-1876
END OF LINE UNIT T4.0 FOR NEEDLEPUNCHED PRODUCTS – 4000mm

PRODUCT TO BE PROCESSED: NEEDLEPUNCHED NONWOVENS
PRODUCT WIDTH: 4.000 MM

WORKING SPEED: 1 – 20 M/MIN

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-1480

SLITTER REWINDER 1800mm WIDTH AND 1000mm DIAMETER-NEW MACHINE

 

TECHNICAL CHARACTERISTICS:

 

UNWINDER

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1100mm

MINIMUM WIDTH: 420mm

MAXIMUM WEIGHT: 300kgs

CORE ID: 3”

 

REWINDER:

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1000mm

MINIMUM WIDTH: 100mm

MAXIMUM WEIGHT PER SHAFT: 300kgs

CORE ID: 3”

 

MATERIAL:

TYPE: 100% PP NONWOVEN

MINIMUM: 10gsm

MAXIMUM: 150gsm

 

TENSION:

MAXIMUM: 2 PLI

 

SPEED:

METERS PER MINUTE: 250

 

DESCRIPTION:

REWINDER MACHINE FOR NONWOVEN ROLLS: UP TO 1000 mm DIAMETER AT UNWINDER AND 1200 mm AT REWINDER.

THE WORKSTATION OFFERS EASY ACCESS TO THE TENSION CONTROL AREA AS WELL AS THE TRIMMING AREA; THIS WAY, ANY MODIFICATION ON THE MATERIAL MEASUREMENTS CAN BE DONE SAFELY.

THE WORKSTATION WILL DELIVER MODULES OF ROLLED MATERIAL WITH SPECIFIC DENSITY, AND SEPARATED FROM EACH OTHER IN ORDER TO KEEP OPERATION CONDITIONS WITHIN REQUIRED QUALITY CONTROLS.

 

UNWINDER WITH SHAFT:

THERE IS A CENTRAL UNWINDING SYSTEM SUPPORTED BY A 3” STEEL EXPANSION SHAFT.

THERE IS A TENSION CONTROL SYSTEM THAT WORKS THROUGH A PNEUMATIC DISK BRAKE WITH A REPLACEABLE PADS SYSTEM.

THE UNWINDER HAS A PIVOTABLE ROLLER SYSTEM WHEREBY TENSION MAY BE MODIFIED ON ONE END TO REDUCE TENSION DIFFERENCE ON MATERIAL IF NECESSARY.

THE SAFETY CHUCK HAS A MECHANICAL MOVEMENT SYSTEM FOR SHAFT INSERTION.

THE UNWINDER HAS AN ULTRASONIC OR LASER SENSOR FOR A REAL MEASURING OF ROLL DIAMETER. THIS INFORMATION WILL HELP TO KEEP A SPECIFIC TENSION ON MATERIAL DURING ALL THE PROCESS.

 

CUTTING:

THE LONGITUDINAL SHEAR CUT SYSTEM GUARANTEES CLEAN AND SAFE TRIMMING AT EVERY MODULE. THE CUTTING SYSTEM ADAPTED TO THE MAIN TRANSMISSION GUARANTEES AN OVER SPEED THAT MAY BE REGULATED ACCORDING TO THE MATERIAL DURING EVERY STAGE OF PROCESS. THE PNEUMATIC ACTIVATION KNIVES WILL ALLOW A FAST MODIFICATION OF THE CUTTING MEASUREMENTS.

THIS ROLLER IS LOCATED AT AN EASY ACCESS AREA FOR THE OPERATOR TO BE ABLE TO MAKE CHANGES ON THE CUTTING WIDTH SAFELY. THE COUNTER KNIVES ARE ASSEMBLED TO THE ROLLER BY 3 SETSCREWS THAT FIX THEIR POSITION ON THE ROLLER. THE COUNTERKNIVES HAVE TWO FACES, SO WHEN THE FIRST FACE HAS AN IMPORTANT WEAR, IT WILL BE REMOVED FROM THE ROLLER AND THE NEW FACE WILL BE PLACED INSTEAD. THIS WILL EXTEND THE LIFESPAN OF THIS IMPORTANT COMPONENT.

SHEAR CUT KNIVES: THERE IS AN ADJUSTMENT MECHANISM TO PLACE THEM ON THE COUNTER KNIFE AND TO ADJUST THE CUTTING LOAD ACCURATELY. THE COUNTER KNIVES ARE SUPPORTED TOWARDS THE ROLLER IN ORDER TO OBTAIN A CUTOFF. THE SPEED ON THIS SYSTEM IS AN OVER SPEED IN RELATION TO THAT OF THE MATERIAL, IN ORDER TO GENERATE A CLEAN CUT.

LONGITUDINAL SHEAR CUT: PNEUMATIC ACTIVATION.

COUNTER KNIVES ROLLER WITH 3 SUPPORT PLANES FOR THE COUNTER KNIVES; 120° DISPLACEMENT FROM EACH OTHER.

19 SLITTERS ARE INCLUDED.

 

REWINDER:

PERIPHERAL REWINDER FOR NONWOVEN. THIS SYSTEM HAS A COUPLE OF MAIN ROLLERS WHERE THE MATERIAL ROLL IS FORMED.

THIS SYSTEM HAS LINEAR GUIDES FOR COMPACTION THROUGH WICH A NIP IS OBTAINED ON THE MATERIAL. THE REWINDER WILL HAVE A TRANSMISSION BASED ON A VECTORIAL-TYPE MOTOR ADAPTED TO A CYCLOIDAL REDUCER. THE TRANSMISSION HAS A MECHANICAL TORQUE CONTROL SYSTEM TO CONTROL THE TORQUE DIFFERENTIAL BETWEEN MAIN ROLLS.

THIS SYSTEM WILL HAVE A 3” EXPANSION SHAFT WHERE THE CARDBOARD CORES WILL BE INSERTED AND THE MATERIAL ROLLS WILL BE FORMED.

 

FABRIC OPENING SYSTEM:

THIS SYSTEM IS BASED ON A VARIABLE CURVATURE SYSTEM BY A CENTER KNOB AND IT IS A BAR- TYPE SYSTEM. THIS KNOB IS THERE TO CONTROL THE CURVATURE OF THE BAR WHERE MATERIAL SLIDES THROUGH. THE SLIDING BAR IS MADE OUT OF AN ULTRA LOW FRICTION MATERIAL IN ORDER TO GENERATE A SMOOTH SLIDING OF MATERIAL WITHOUT ANY TENSION ADDED. THIS WILL REDUCE WRINKLES IN A SIGNIFICANT WAY.

 

AUTOMATIC TENSION SYSTEM:

THERE IS AN OPEN LOOP AUTOMATIC TENSION CONTROL SYSTEM WITH A SENSOR FOR DIAMETER MEASURING. BY THIS SYSTEM, A REAL VALUE OF DIAMETER IS OBTAINED AT THE REWINDER. PRESSURE OF PNEUMATIC BRAKE VARIES DURING PROCESS.

 

MANUAL POSITIONING (OPTIONAL):

THE MANUAL POSITIONING SYSTEM IS BASED ON THE POSITION CONTROL OF THE COUNTER KNIVES. THE MODULE IS POSITIONED AT A DESIRED CUTTING PARAMETER AND THE COUNTER KNIFE WILL PHYSICALLY COME ACROSS IT. THE REAL POSITION OF MODULE WILL BE SHOWN ON A SCREEN THAT OPERATOR WILL BE CONSTANTLY SUPERVISING. THIS SCREEN WILL SHOW THE REAL MEASUREMENTS OF THE CARRIAGE IN RELATION TO THE LAST ONE OR AS AN ABSOLUTE REFERENCE. OPERATOR WILL BE ABLE TO RESET THE MEASUREMENT ONCE THE COUNTER KNIFE IS REPLACED AND WILL REPEAT THIS PROCESS EVERY TIME A COUNTER KNIFE IS POSITIONED.

A DISPLAY WILL SHOW THE DESIRED POSITION IN MILLIMETERS OR INCHES.

THIS SYSTEM CAN SHOW MEASUREMENT IN AN EITHER ABSOLUTE OR INCREASING WAY.

POSITION TOLERANCE: +/- 0.30 mm.

THE POSITIONER IS INSTALLED ON A SUPPORT THAT WILL BE LOCATED ON THE REWINDER BENCHES. THEREFORE, THERE WILL BE AN EASY ACCESS TO SYSTEM AND AN EASY REPETITION OF POSITIONING PROCESS.

 

UNLOADING ROLL TABLE:

A HYDRAULIC PIVOTEABLE TABLE WILL HAVE AS MAIN FUNCTION THE UNLOADING OF FINISHED ROLLS THAT THEN WILL BE LOCATED ON FLOOR LEVEL. THIS SYSTEM WILL EJECT THE ROLL AND THEN IT WILL BE RECEIVED AT THE PIVOTING TABLE FOR AN EFFICIENT UNLOADING.

THE UNLOADING TABLE WILL ALSO WORK AS A PROTECTION FOR THE OPERATOR.

THIS EQUIPMENT WILL HAVE SECURITY CURTAINS AT FRONT TO KEEP OPERATOR FROM ENTERING THE REWINDING AREA. THERE WILL BE AN EMERGENCY STOP BUTTON OR WIRE WHERE OPERATOR WORKS AND WILL ALSO HAVE PHYSICAL PROTECTION WITH SECURITY SWITCHES AT CUTTING AREA.

 

CONTROL:

HMI CENTRAL CONTROL SYSTEM WITH TOUCH SCREEN TO PROGRAM THE OPERATION CYCLE AND ALL THE MATERIAL CHARACTERISTICS. OPERATOR WILL HAVE ACCESS TO ALL OPERATION PARAMETERS IN ORDER TO BE ABLE TO MAKE CHANGES ON THE EQUIPMENT OPERATION CONDITIONS, AND THEREFORE OBTAIN MATERIAL ROLLS WITH SPECIFIC DENSITIES.

TRANSMISSION: VECTORIAL MOTO REDUCER WITH 1000:1 TORQUE.

DIGITAL METER COUNTER WITH DISPLAY AND AUTOMATIC STOP AT DEFINED DISTANCE.

 

DOCUMENTS INCLUDED:

THE MACHINE WILL BE DELIVERED WITH THE FOLLOWING DOCUMENT:

OPERATION MANUAL

MAINTENANCE MANUAL

SAFETY MANUAL

ELECTRIC DIAGRAMS

CONTROL SYSTEM MANUAL

PLC BACKUP

REQUIREMENTS:

ELECTRIC 15 KW, 440 VAC, TRI PHASE.

PNEUMATIC 6 BAR - 60 LTS. / MIN.

 

DUCTS AND WIRING:

DUCTS AND WIRES RUNNING FROM UTILITIES SOURCES TO THE CONTROL PANEL AND FROM THE CONTROL PANEL TO THE MACHINE WILL BE AT CUSTOMER COSTS AND MUST BE DONE ACCORDING TO THE INSTRUCTIONS SHOWN IN OUR DIAGRAMS

 

SIEMENS PLC

Learn More

C-3994 BARGEMOUNTED POWER PLANT, CAPACITY 220MW

A. ONCE THROUGH STEAM GENERATOR
B. BARGE
C. CHILLERS
D. AIR COMPRESSOR
E. GAS TURBINE
F. STEAM TURBINE
G. FEEDWATER SYSTEM
H. CLOSED COOLING WATER SYSTEM
I. AUXILIARY COOLING WATER SYSTEM
J. CONDENSATE POLISHING UNIT (CPU)
K. WASTE WATER SYSTEM
L. PLANT ELECTRICAL SYSTEM
M. BLACK START DG SET
N. PLANT CONTROLS AND INSTRUMENTATION
O. PLANT FIRE FIGHTING SYSTEM
P. START UP VACUUM SYSTEM
Q. STEAM TURBINE DEAERATING CONDENSER

QUANTITY: 1 PLANT

Learn More

C-3980 KRAFT PAPER MAKING MACHINE WITH GAS BOILER, CAPACITY 3 TO 5 T/D, NET PAPER WIDTH 1200mm

KRAFT PAPER MAKING MACHINE
WITH GAS BOILER
CAPACITY: 3 TO 5 T/D KRAFT PAPER MACHINE
1092 KRAFT CORRUGATED PAPER MACHINE
WITH RECYCLE PAPER AS RAW MATERIAL
TECHNICAL PARAMETER:
OUTPUT: KRAFT PAPER, CORRUGATED PAPER
WEIGHT: 60 TO 180G/M2
NET PAPER WIDTH: 1200mm

QUANTITY: 1

Learn More

A-1640 DILO DILOOP DS 45 STRUCTURAL NEEDLE LOOM, WIDTH 4500mm, YEAR 1989

TYPE: DI-LOOP DS 45
WIDTH: 4500 mm
YEAR: 1989
EL: 380 / 3 / 50

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-5393 (2206YBJL1UM) L TUFTCO COATING LINE WITH FOAM MACHINE AND SLITTING OPERATION TUFTO COATING LINE FOR EMBOSSED UNITARY BACKED RUGS USING WASHABLE LATEX FOR EMBOSSED WASHABLE RUGS – SET UP FOR 12’ WIDTH AND INCLUDES THE FOLLOWING: TISI MODEL 38500 BUTT SEAMER WITH TRIMMER ON RAIL ENTRANCE J-BOX VERTICAL KEYON PIN TENTER DIRECT COAT APPLICATOR, ROLL OVER ROLL WITH TRAVERSING SYSTEM DAY TANK TO FEED LATEX TO FROTH MACHINE EASE TYPE FROTH MACHINE PRE-STEAMER BANK OF ELECTRIC INFRAREDS TWO BASKET-WEAVE EMBOSSING ROLLERS FOR 12’ WIDTHS FOUR MODULE NATURAL GAS HEATED TUFTCO CURING OVEN COOL OUT SECTION SLITTING SECTION WITH EIGHT SLITTING HEADS AND A CAMERA GUIDING SYSTEM 10 LOOP ACCUMULATOR ROLLUP ELECTRICAL CONTROL SYSTEM BY TUFTCO SPEED RANGE: LINE SPEED FOR COATING 50 OUNCE/SQUARE YARD FACE WEIGHT WITH 24 OZ/SQUARE YARD OF EMBOSSIBLE LATEX IS 35FPM, LINE SPEED FOR COATING 30 OZ/SQUARE YARD FACE WEIGHT WITH 20 OZ/SQUARE YARD OF EMBOSSIBLE LATEX IS 45 FPM. TOILET SEAT CONVERS ARE COATED WITH APPROXIMATELY 7 OZ/SQUARE YARD AT 70 FPM. NOTE THE MAXIMUM MECHANICAL SPEED OF THE COATING LINE IS 70 FPM. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5249 (131342CBQ12U) L DUSENBERY 815 DUPLEX SLITTER REWINDER 84” WITH DUSENBERY 863 SHAFT TYPE UNWIND STAND QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: A-1245 (0101GHBXX12) A CARPETING RELATED MACHINERY REFERENCE #300: 100 HIRSCHBURGER WINDING HEADS, CYLINDRIC TUBES, TRAVERSE 250MM REFERENCE #301: GILBOS WINDERS, 4 SETS OF 6 SPINDLES EACH REFERENCE #302: 1 ICBT TWO-FOR-ONE TWISTER – 2X36 POSITIONS – UP TO TWIST 10.000 DEN REFERENCE #303: 1X12 POSITIONS GILBOS WINDERS WITH AUTODOFFING REFERENCE #304: 1 CARPET FORMING MACHINE FOR STAIR CARPET PIECES REFERENCE #305: 1 AUTOCLAVE FOR CARPET YARNS, LENGTH 5.60 M, INNER DIAMETER 1.60 M REFERENCE #307: 2 MENDING-GUNS REFERENCE #308: KNIFES, NEEDLES, LOOPERS FOR TUFTING MACHINERY REFERENCE #309: 2 X DIETZE & SCHELL – AIRENTANGLING – EACH 4 POSISITONS + 4 WINDERS QUANTITY AVAILABLE: 9 Learn More

REFERENCE NUMBER: J-0030 (1313KDVBMNXX12) ROSENTHAL SHEETER YEAR 2008 WIDTH 1830mm ROSENTHAL SHEETER, DUAL UNWINDS, TWO CUTTING HEADS WAS-6-DUJEAAAAC7 WITH SERVO DRIVE AND VACUUM POSITIONING CONVEYOR YEAR: 2008 WIDTH 1830mm QUANTITY AVAILABLE: 1 Learn More