Search results for: 'Steel ta'

REFERENCE NUMBER: A-1876
END OF LINE UNIT T4.0 FOR NEEDLEPUNCHED PRODUCTS – 4000mm

PRODUCT TO BE PROCESSED: NEEDLEPUNCHED NONWOVENS
PRODUCT WIDTH: 4.000 MM

WORKING SPEED: 1 – 20 M/MIN

QUANTITY: 1

Learn More

REFERENCE NUMBER: V-0052 ADHESIVE APPLICATION MACHINE (FOR FOAM, MATTRESSES) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-2042 (770IDFGXX6) WISCONSIN OVEN GAS FIRED BATCH OVEN FOR TEMPERING MATTRESS INNERSPRINGS GAS FIRED BATCH OVEN MANUFACTURER: WISCONSIN OVEN STILL ASSEMBLED TODAY OVEN WILL BE USED FOR TEMPERING STEEL SPRING ASSEMBLIES WITH A LOADING OF APPROXIMATELY 50 ASSEMBLIES WEIGHING APPROXIMATELY 40 POUNDS, IN THE OVEN AT A TIME THE SIZE IS BASED ON APPROXIMATELY 4 TO 5 CYCLES PER HOUR PROVIDING THE LOADING AND UNLOADING IS ACCOMPLISHED PROMPTLY THE HEATING RATE IS BASED ON A HEATING CYCLE OF APPROXIMATELY 12 MINUTES PER CYCLE THE OVEN WILL INCLUDE, BUT NOT BE LIMITED TO, THE DEISNG FEATURES OUTLINED IN OUR SPECIFICATIONS LISTED BELOW FURTHER MODIFICATIONS AND DESIGN CHANGES MAY BE INCORPORATED AT THE FINAL ENGINEERING STAGES TO PRODUCE THE BEST EQUIPMENT POSSIBLE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-5045-B CONCRETE BATCHING CEMENT PLANT QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-5045-A CONCRETE BATCHING CEMENT PLANT QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-8444 PUNCHING MACHINE MODEL FST 11 MACHINE AVAILABLE FOR AUTOMATIC DRILLING IN SHEETS OF PU FOAM, MEMORY FOAM, LATEX, EVA, NEOPRENE. WITH 20mm THICKNESS UP 2 DRILLINGS PER SECOND ARE PERFORMED; E.G.: ONE MOULD FOR 2mm DIAM. HOLES AND 50mm WHEEL BASE OF PUNCH, 7mm X 3.5 CROSSED HOLE PITCH: THE MACHINE WILL PERFORM NO 2310 HOLES EACH DRILLING CYCLE WITH 4620 HOLES PER SECOND IN TOTAL. THAT MEANS THE MACHINE CAN DRILL A FOAM SHEET DIM. 1000X1100mm EACH 20 SECONDS WITH 92400 HOLES IN TOTAL. TWO DRILLING TYPES ARE POSSIBLE: CONTINUOUS DRILLING “A-PERFORM” (NO DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS –SEE TAB. 31A); CONTINUOUS DRILLING “B-PERFORM” (WITH FIXED DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS). THE DISTANCE CAN BE MODIFIED BY OPERATOR). UP TO 150 20mm-THICKNESS MATTRESSES CAN BE PRODUCED IN ONE HOUR; BY INCREASING THE THICKNESS THE PRODUCTION WILL REDUCE. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-8444-A PUNCHING MACHINE MODEL FST 11 FOR LATEX MACHINE AVAILABLE FOR AUTOMATIC DRILLING IN SHEETS OF PU FOAM, MEMORY FOAM, LATEX, EVA, NEOPRENE. WITH 20mm THICKNESS UP 2 DRILLINGS PER SECOND ARE PERFORMED; E.G.: ONE MOULD FOR 2mm DIAM. HOLES AND 50mm WHEEL BASE OF PUNCH, 7mm X 3.5 CROSSED HOLE PITCH: THE MACHINE WILL PERFORM NO 2310 HOLES EACH DRILLING CYCLE WITH 4620 HOLES PER SECOND IN TOTAL. THAT MEANS THE MACHINE CAN DRILL A FOAM SHEET DIM. 1000X1100mm EACH 20 SECONDS WITH 92400 HOLES IN TOTAL. TWO DRILLING TYPES ARE POSSIBLE: CONTINUOUS DRILLING “A-PERFORM” (NO DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS –SEE TAB. 31A); CONTINUOUS DRILLING “B-PERFORM” (WITH FIXED DISTANCE BETWEEN TWO IN SUCCESSION DRILLINGS). THE DISTANCE CAN BE MODIFIED BY OPERATOR). UP TO 150 20mm-THICKNESS MATTRESSES CAN BE PRODUCED IN ONE HOUR; BY INCREASING THE THICKNESS THE PRODUCTION WILL REDUCE. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: T-6843 SPINNBAU NONWOVEN LINE, YEAR 1994 BRAND: SPINNBAU SHORT DESCRIPTION: NONWOVEN LINE YEAR: 1994 NONWOVEN LINE CONSISTING OF 1. CARD FEEDING: CARD FEEDING R&S, NEW, IN 2500mm WORKING WIDTH, CONSISTING OF: ONE R&S MATERIAL BIN IN 2500mm WORKING WIDTH, 600mm DEPTH AND A COMPLETE HEIGHT OF 2500mm, WITH TOP AND BOTTOM WINDOW AT BOTH SIDES, FILLING LEVEL CONTROLLED BY IN HEIGHT ADJUSTABLE INFRARED DEVICES. ONE DOOR AT THE BACKSIDE FOR CLEANING, LOCKED BY SECURITY SWITCHES. THE VITIATED AIR ESCAPES THROUGH THE PERFORATED SHEETMETAL AT THE TOP. THESE AREAS ARE COMPLETELY COVERED, THE OUTGOING AIR CAN BE FILTERED BY AN EXCISTING FILTERSTATION OR OPTIONALLY BY FILTERBAGS, 2 DELIVERY ROLLERS. ONE R & S CHUTE FEEDER IN 2500mm WORKING WIDTH CONSISTING OF: ONE OPENING ROLLER DIAMETER 450mm, ONE VIBRATION CHUTE, FIBRELEVEL CONTROLLED BY ULTRASONIC, CHUTE ADJUSTABLE OVER TOOTH RAILS IN DEPTH FROM 80 TO 240mm, TWO DRAWING OFF ROLLERS, ONE FEEDING TABLE WITH TRANSILON BELT, PREPARED FOR SERVOLAP. DRIVES: DELIVERY ROLLERS: AC -GEARBOXMOTOR 0.55 KW, FC OPENING ROLLER: AC-MOTOR 2.2 KW VIBRATION: AC-GEARBOXMOTOR, 0.55 KW, FC FEEDING TABLE: AC-GEARBOXMOTOR, 0.55 KW, FC 2. CARDING; ONE SPINNBAU DOUBLE DOFFER CARD, IN 2500mm WORKING WIDTH, YEAR 1994: CARD, FOLLOWING EQUIPPED: 1 CYLINDER FEEDING DEVICE WITH FEED PLATE: 1 FEED ROLLER DIAMETER 159mm 1 LICKER-IN DIAMETER 292mm PRE-OPENING: 1 BREAST DIAMETER 412mm 1/1 WORKER/STRIPPER DIAMETER 213/118mm 1 INTERMETE ROLLER DIAMETER 412mm CARD: 1 MAIN CYLINDER DIAMETER 1500mm 5/5 WORKERS/STRIPPERS DIAMETER 213/118mm 1 DOFFER, TOP DIAMETER 550mm 1 DOFFER, BOTTOM DIAMETER 550mm 2 CONDENSING ROLLERS TOP DIAMETER 292mm TOP DRAWING OFF DEVICE, NEW: 1 DRAWING OFF ROLLER/WIRED DIAMETER 159mm 1 DRAWING OFF ROLLER/STEEL RUBBER: DIAMETER 159mm 1 CLEANING ROLLER WITH INTEGRATED ELECTRONIC, WHEN DIAMETER OF CLEANING IS GETTING BIGGER, CARD WILL STOP. BOTTOM DRAWING OFF DEVICE, NEW: 1 DRAWING OFF ROLLER/WIRED DIAMETER 159mm 1 DRAWING OFF ROLLER/STEEL RUBBER: DIAMETER 159mm 1 CLEANING ROLLER WITH INTEGRATED ELECTRONIC, WHEN DIAMETER OF CLEANING IS GETTING BIGGER, CARD WILL STOP. DRAWING OFF TABLES: TOP TRANSILON BELT BOTTOM: TRANSILON BELT COVERS: THE CARD HAS COVERS TO CLAP UP AND DOWN (SECURED WHEN CLAPPED UP), THE SIDES ARE FULLY COVERED AND ELECTRONICALLY LOCKED. RIGID WIRE: ONE COMPLETE SET OF RIGID WIRE, MOUNTED, FOR FIBRES 1.5 DTEX - 17 DTEX, CAPACITY UP TO 800 KG/H ELECTRIC: VOLTAGE: ~400 V AC, 3 PHASES CONTROL VOLTAGE: ~220 V AC, =24V DC FREQUENCY: 50 Hz COLOUR: MACHINE: RAL 5015/ 9001 (IF YOU LIKE WE CAN CHANGE) CONTROL CABINET: RAL 7032, GREY SWITCH BOARD: RAL 7032, GREY ELECTRICAL DRIVES: FEED ROLLER: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED LICKER-IN: MECHANICAL FROM BREAST BREAST: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED WORKERS BREAST: MECHANICALLY FROM BREAST INTERMEDIATE ROLLER: MECHANICALLY FROM MAINSWIFT MAIN SWIFT: 1 AC-MOTOR FREQUENCY CONTROLLED WORKERS: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED DOFFERS: 2 AC GEARBOXMOTORS. FREQUENCY CONTROLLED CONDENSING ROLLERS: 1 AC GEARBOXMOTORS. FREQUENCY CONTROLLED DRAWING-OFF DEVICES: 2 AC GEARBOXMOTORS. FREQUENCY CONTROLLED DRAWING-OFF TABLES: 2 AC GEARBOXMOTORS, FREQUENCY CONTROLLED SWITCHBOARDS AND CONTROLS: SWITCHBOARDS RITTAL SERIES, COMPLETE WIRED. SWITCHBOARDS WITHOUT COOLING DEVICES. CONTROL CABINET OPERATION WITH COLOURED SCREEN, FITTED IN CONTROL CABINET OPERATED BY SIEMENS SPS S7-300 1 SET OF CABLE MATERIAL: FOR 20 MTR LENGTH BETWEEN MACHINERY AND SWITCHBOARD WITHOUT INSTALLATION MATERIAL ERECTION AND STARTING UP: IS NOT INCLUDED, SHOULD BE MADE BY US FOUNDATION: ONE FOUNDATION IN 750mm HEIGHT, WITH SIDEWALKS AROUND, TWO STEPS ON EACH SIDE. SUCTION: CONNECTION FOR THE DOFFER AND TOP OF CARD 3. CROSSLAPPING, NEW: ONE REISKY & SCHLESE CROSSLAPPER, TYPE RS 100 IN 2500mm WORKING WIDTH (BELT WIDTH 2800mm) AND 2500mm LAPPING WIDTH (BELT WIDTH 2700mm) MAX INFEEDING SPEED: 100 MTR/MIN, DELIVERY SPEED OF DRAWING OFF TABLE: FROM 0 TO 20 MTR/MIN, CONSISTING OF: ONE FEEDING TABLE IN 1000mm LENGTH MOUNTED IN IT'S OWN FRAME, ADJUSTABLE IN THE HEIGHT ACCORDING TO THE DOFFER, FURTHER THE COMPLETE FEEDING TABLE CAN BE MOVED UP IF THE DOFFER HAS TO BE DRAWN BACK. THE CROSSLAPPER ITSELF GUIDES THE WEB FROM THE INFEED DOWN TO THE OUTLET BETWEEN THE CONVEYORS, WHICH HAVE ANTISTATIC PROPERTIES. THE TENSION AND THE DISTANCES BETWEEN THEM CAN BE ADJUSTED ACCORDING TO THE DIFFERENT FIBRES. THE CONVEYORS ARE EQUIPPED WITH AUTOMATIC EDGE GUIDES, SO THAT THEY ARE RUNNING IN THE CENTRE. THE LAID WEB IS COVERED BY THEM. THE SERVO- DRIVES ARE RESPONSIBLE FOR THE PERFECT SYNCHRONISATION AND THE EXACT REVERSAL OF THE CARRIERS. THE SWITCHBOARD IS EQUIPPED WITH A COULOURED TOUCHSCREEEN, WHERE ALL NECESSARY PARAMETERS CAN BE PROGRAMMED, ALSO DIFFERENT CURVES FOR STORING THE WEB DURING REVERSALS. DRIVES: FEED TABLE: AC-SERVO-MOTOR BELT 1: AC-SERVO-MOTOR BELT 2: AC-SERVO-MOTOR TOP CARRIER: AC-SERVO-MOTOR BOTTOM CARRIER: AC-SERVO-MOTOR DRAWING OFF TABLE: AC-SERVO-MOTOR HEIGHT DRAWING OFF TABLE LEFT: AC-LINEARMOTOR HEIGHT DRAWING OFF TABLE RIGHT: AC-LINEARMOTOR OPERATION: BY COLOURED TOUCHSCREEN, SIEMENS IN CONTROL CABINET OF CARD. PARAMETERS: MANUEL / INLINE INFEED SPEED DRAFT (INFEED SPEED/LAYING SPEED) NUMBER OF LAPS LAPPING WIDTH FROM MIDDLE TO THE LEFT AND TO THE RIGHT DRAWING OFF SPEED AUTOMATICALLY SHOWN DEPENDING ON LAYERS DARWING OFF TABLE HEIGHT LEFT / RIGHT LAYING SPEED RECEIPES FAULT SHOWING SWITCHBOARD AND ELECTRONIC DEVICES: SWITCH BOAD RITTAL, COMPLETE WIRED. SWITCHBOARD WITHOUT COOLING DEVICE. CONTROL PANNEL RITTAL. CONTROLLED BY S7 SIEMENS 10000mm OF CABLES BETWEEN SWITHBOARD AND MACHINE/CONTROLPANEL QUANTITY: 1 Learn More

REFERENCE NUMBER: M-5221 (1313565TNY12RX) L
NONWOVEN LINE WIDTH 2500mm

CARD FEEDING
CARDING

QUANTITY AVAILABLE: 1

Learn More

REFERENCE NUMBER: G-1384 VERTICAL SEMIAUTOMATIC FOAM CUTTING MACHINE MODEL BF 2200 WORKING TABLE ON THE RIGHT OF BLADE 2200mm (86.6") WORKING TABLE ON THE LEFT OF BLADE 1280mm (50") WORKING CUTTING LENGTH 2400mm (94.4") WORKING CUTTING HEIGHT 1300mm (51") HEADBOARD HEIGHT 1250mm (49") QUANTITY AVAILABLE: 1 Learn More