Search results for: 'thermal b'

M-5175 OLBRICH COATING LINE FOR MANUFACTURING TARPAULIN AND BANNER PVC COATED FABRICS 3300mm

KNIFE OVER ROLL COATING
LIST OF EQUIPMENT FOR MANUFACTURING OF PVC COATED FABRICS, LINE CAN APPLY ANY TYPE OF COATING INCLUDING WATER BASED OR SOLVENT BASED AND EITHER CLEAR COAT THE FABRIC OR SATURATE COAT ANY WOVEN FABRIC , CAN ALSO DO SUNBRELLA TYPE TECHNICAL TEXTILES
FOR ONE SIDE COATING WITH KISS COATER

MANUFACTURED BY OLBRICH GMBH (ERECTED IN 2005) 3400mm (SCRIM CAN BE 3400mm WIDTH)
CAN MAKE 3350mm COATED FABRIC AND AFTER TRIMMED EDGES HAVE A FINISHED PRODUCT OF 3300mm (BEGINNING WITH A 3400mm SCRIM , THERE ARE INBUILT CUTTING BLADES FOR TRIMMING .
MANUFACTURED IN GERMANY BEGINNING 2003 AND 2004

COATING LINE
UNWINDER
PENDULUM
WEB CONTROL UNIT
PULLING STATION
PENDULUM
HEATING ROLLER (DIAMETER 570 mm)
PLATFORM
SAWING GAUGE
DOUBLE-KNIFE (DOCTOR) VERTICAL COATING MACHINE
VERTICAL DRIER
COOLING STATION WITH ROLLER LOCK
PENDULUM
SMOOTHING ROLL
MACHINE FRAME
IDLER ROLLER BRIDGE
PULLING STATION
PLATFORM
COATING MACHINE (KNIFE-OVER-ROLL)
HORIZONTAL DRIER
COOLING STATION
IDLER ROLLER BRIDGE
PLATFORM
SMOOTHING CALENDER
SUCTION HOOD
LACQUERING MACHINE (ZIMMER)
TEMPERATURE CONTROL UNIT
DRYER
ACCUMULATOR OF FABRIC
COMPUTER WITH SOFTWARE CONTROL
(SIEMENS)
ELECTRICAL CONTROL PLANT
WEIGHT-PER-UNIT-AREA
MEASURING GAUGE (2 UNITS MAHLO)-ISOTOPE NOT INCLUDED
REWINDER
FREE STANDING SLITTER-REWINDER (SEE PHOTO ATTACHED)
TRIMMING GOUGE

PERIPHERAL EQUIPMENT
LIQUIFIED GAS EQUIPMENT RH80 (RANSOME MANUFACTURING USA)
EVAPORATOR-RANSOME (USA)
CHILLER (ITALY) WITH EXPANSION TANK
BOILER ERENSAN MODEL 2000 (ISI SANAYI A.S. TURKEY) FOR HEATING OIL WITH EXPANSION TANK.
\BOILER FOR HEATING BUILDING, NOT INCLUDED
REGENERATIVE THERMAL OXIDIZER (RTO) ENVIROLOGIC USA
12 STAINLESS STEEL CONTAINERS FOR PLASTISOL VOLUME -1 M3
VACUUM DISSOLVER (SRUGO)-2 UNITS
PIPING, EXHAUST VENT PIPES (NO BUILDING HEATING PIPES )
OVERHEAD CRANE NOT INCLUDED

FLOORSPACE OCCUPIED BY THE LINE:
LENGTH 67,125mm
WIDTH 6200mm
HEIGHT 8100mm

SPEED 3 TO 30 M/MIN

HEATING SYSTEM: OIL

QUANTITY: 1 LINE

Learn More

P-5090 JOPER CAST IRON ROASTER 60 KILOS

ONE BAG ROASTING – WORLDWIDE FAVORITE SINCE MOST OF THE COFFEE BAGS IN THE WORLD ARE 60 KILO. NOW THIS IS NOT AN EXCUSE TO AVOID SILO MANAGEMENT OF THE COFFEE BEANS - AS COFFEE STORED IN SILOS ENJOY A UNIVERSAL MOISTURE CONTENT WHERE LEAVING IT IN BAGS WILL GIVE YOU MOISTURE ALL OVER THE PLACE - SO THINK SILOS AS PART OF YOUR PLANT. NOW TO THE ACTUAL ROASTER BEING A VERY RUGGED CAST IRON ROASTING FRAME AND ROASTING DRUM CONTACT-CLEARANCES WITH THAT SOLID FRAME MAKING IT JUST PLAIN SOLID AND DOES NOT MOVE UNDER LONG OR EXTENDED USE. DOUBLE WALL DRUM MEANS THAT THE HEAT IS ALL DESIGNED TO GO THROUGH THE CENTER OF THE ROASTING CHAMBER, NOT "ONTO" THE DRUM EXTERIOR. TOTAL TRUE CONVECTION. NOT ONLY IS THIS THE SAME STYLE FROM THE OLD GOTHOT & BARTH ROASTER DAYS. . . BUT EVEN BETTER AS THE SHAFT DESIGN SO THAT BEARINGS ARE EXTERNALLY MOUNTED AND ADDITIONALLY ARE AIR COOLED FOR LONG LIFE AND TROUBLE-FREE CONTROL. EVEN THE SIDE PANELS OR PRODUCT FLIGHTS HAVE A LONGER CURVE POSITIONING THAT ALLOWS FOR MORE PRODUCT FLOW INTO THE HOT AIR STREAM, RESULTING IN A SLIGHTLY MORE RAPID ROAST WITH MORE EVEN BEAN INTERIOR AND EXPANSION THAT FRANKLY LEADS THE INDUSTRY.

ALL THIS COMMENTARY ABOVE MEANS THIS ROASTER SIMPLY IS MORE QUIET THAN ANYTHING ON THE MARKET. PERIOD. THERMAL INSULATION WITH HIGHEST QUALITY OF FIBER FOR LOW GAS CONSUMPTION; DIGITAL TEMPERATURE CONTROL. CYCLONE IS SEPARATE. THE COOLER, BEING TOTALLY SEPARATE ALSO HAS THE LARGEST AIR COLLECTION AREA OF ANY ROASTER MADE ALLOWING FOR TOTAL AMBIENT COOL COFFEE IN LESS THAN THREE MINUTES. ADD TO THIS PACKAGE A LOADER OR YOUR CHOICE OF DESTONERS AND EVEN YOUR CHOICE OF CONTROL METHODS. . . SEE BELOW FOR DETAILS. SPECIAL NOTE - THE MORE AUTOMATIC VERSIONS OF THIS ROASTER MEANS THAT EVERYTHING IS TOTALLY DIFFERENT FROM THE BURNER TO THE MOTORS USED TO CONTROL EACH FUNCTION - AS THEY ARE ALL SPEED CONTROLLED - SO THERE IS A HUGE DIFFERENCE BETWEEN THE "MANUAL" METHOD AND THE AUTOMATIC AND PROFILE OPERATED MACHINE.

SPACE PLANNING AND DRAWINGS - WE ARE HAPPY TO DRAW THIS INTO YOUR DRAWINGS, SO THAT YOU CAN SEE SPECIFICALLY JUST WHERE AND HOW THIS WILL FUNCTION WITHIN YOUR PLANT. PLEASE SEND YOUR DRAWINGS FOR A DETAIL STUDY.

BUILT TO UL295 STANDARDS.

QUANTITY: 1

Learn More

P-5079 COMMERCIAL JOPER CAST IRON CRM-30 ROASTER 30 KILOS

WHAT WE HAVE HERE IS A VERY RUGGED CAST IRON ROASTING FRAME AND ROASTING CONTACT CLEARANCES WITH THE MACHINE - JUST PLAIN SOLID AND DOES NOT MOVE UNDER LONG OR EXTENDED USE. DOUBLE WALL DRUM MEANS THAT THE HEAT IS ALL DESIGNED TO GO THROUGH THE CENTER OF THE ROASTING CHAMBER, NOT "ONTO" THE DRUM EXTERIOR. TOTAL TRUE CONVECTION. NOT ONLY IS THIS THE SAME STYLE FROM THE OLD GOTHOT & BARTH ROASTER DAYS. . . BUT EVEN BETTER AS THE SHAFT DESIGN SO THAT BEARINGS ARE EXTERNALLY MOUNTED AND ADDITIONALLY ARE AIR COOLED FOR LONG LIFE AND TROUBLE-FREE CONTROL. EVEN THE SIDE PANELS OR PRODUCT FLIGHTS HAVE A LONGER CURVE POSITIONING MORE PRODUCT FLOW INTO THE HOT AIR STREAM, RESULTING IN A SLIGHTLY MORE RAPID ROAST WITH MORE EVEN BEAN INTERIOR AND EXPANSION THAT FRANKLY LEADS THE INDUSTRY.

ALL THIS COMMENTARY ABOVE MEANS THIS ROASTER SIMPLY IS MORE QUIET THAN ANYTHING ON THE MARKET. PERIOD. THERMAL INSULATION WITH HIGHEST QUALITY OF FIBER FOR LOW GAS CONSUMPTION; DIGITAL TEMPERATURE CONTROL. CYCLONE IS SEPARATE. THE COOLER, BEING TOTALLY SEPARATE ALSO HAS THE LARGEST AIR COLLECTION AREA OF ANY ROASTER MADE ALLOWING FOR TOTAL AMBIENT COOL COFFEE IN LESS THAN THREE MINUTES. ADD TO THIS PACKAGE A LOADER OR YOUR CHOICE OF DESTONERS AND EVEN YOUR CHOICE OF CONTROL METHODS.

DATA INFORMATION:
BATCH CAPACITY: 30 KG / 66 LBS
CONTROL DESIGN: MANUAL
CAPACITY PER HOUR: 120 KG / 265 LBS
ROASTING TIME: 12-18 MIN (4 BATCHES AN HOUR)
EXHAUST AIR TREATMENT: OPTIONAL
COOLING CYCLONE: OPTIONAL
PRE-COOLING WITH WATER IN DRUM: OPTIONAL
COOLING TIME: 3-4 MIN
TYPE OF COOLING: AIR AMBIENT
SAFETY DEVICE: YES
BURNER POWER: 110 KW / 375000 BTU
BURNERS MANUFACTURER: RIELLO
OPERATION TYPE BURNER: BS2D-2 STAGE
FUEL TYPE: PROPANE/NAUTRAL GAS/DIESEL
SIDE OF OPERATION: LEFT
POWER REQUIREMENTS: 20 AMP
VOLTAGE/FREQUENCY/PHASES: 400+N-230 V / 50-60 HZ / 3 PH
9 AMP. . . 3 PHASE 50/60 HZ PREFERRED, YOUR CHOICE OF 220/440 - SINGLE PHASE AVAILABLE AT SPECIAL REQUEST
(NOTE ON 3 PHASE. . . NOT ONLY IS IT LESS EXPENSIVE TO OPERATE, BUT IT RUNS MORE QUIETLY THAN SINGLE PHASE WHENEVER OR WHEREVER IT IS USED. KEEP THIS IN MIND FOR ANY MACHINERY.)
Ø EXHAUST CHIMNEY (ROASTER CYCLONE): 250MM / 9,8 INCH
Ø EXHAUST CHIMNEY (COOLER): 250MM / 9,8 INCH
Ø HOPPER ROAST CHIMNEY: 150MM / 5,9 INCH
ROASTER WEIGHT WITH CYCLONE: 1050 KG / 2310 LBS
COOLER WEIGHT: 300 KG / 660 LBS
ROASTER FAN MOTOR: 1, 5 HP
COOLER FAN: 4 HP
DRUM GEARBOX: 1 HP
COOLER GEARBOX: 0, 75 HP
BUILT TO UL295 STANDARDS.

QUANTITY: 1

Learn More

M-6051 NEEDLE FELT / THERMOSET LINE, WIDTH 3000mm TO 4400mm, YEAR 1992 TO 2010

OFFER 001
NEEDLE FELT / THERMOSET LINE
WORKING WIDTH: 3200mm
WEIGHT: 60 TO 400 G/M2

OFFER 002
BONINO CARDING MACHINE
WORKING WIDTH: 3000mm

OFFER 003
AUTOMATEX CROSSLAPPER
WORKING WIDTH IN: 3000mm
WORKING WIDTH OUT: 4000mm

OFFER 004
FEHRER PRE-NEEDLING
YEAR: 1992
WORKING WIDTH: 4400mm

OFFER 005
BRUNATI DRYER
WORKING WIDTH IN: 3400mm
WORKING WIDTH OUT: 3400mm

OFFER 006
ORV SLITTING
WORKING WIDTH: 3600mm

OFFER 007
MT AUTOMATIC WINDER
YEAR: 2010
WORKING WIDTH: 3500mm

QUANTITY: 1 LINE

Learn More

M-6052 NEEDLE FELT / THERMOSET LINE, WORKING WIDTH 3000mm TO 3600mm, YEAR 1988

OFFER 001
NEEDLE FELT / THERMOSET LINE
WORKING WIDTH: 3200mm

OFFER 002
BEMATIC CARDING MACHINE
YEAR: 1988
WORKING WIDTH: 3000mm

OFFER 003
AUTOMATEX CROSSLAPPER
YEAR: 1988
WORKING WIDTH IN: 3000mm

OFFER 004
BRUNATI DRYER
WORKING WIDTH IN: 3400mm

OFFER 005
ORV SLITTING – WINDER
WORKING WIDTH: 3600mm

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: P-2127 BRAZZOLI HT ROPE DYEING MACHINES YEAR 2001 800 KILOGRAMS BRAZZOLI TYPE: HT ROPE DYEING MACHINES YEAR: 2001 140°C 4.55 BAR LOW LIQUOR RATIO (FROM 1/6 to 1/8) TYPE: SIRIO HT 800 4 TUBES 800 KILOGRAMS EACH MACHINE WITH: TURBOVARIO DEVICE (VARIABLE BATH PASSAGE CROSS SECTION THAT GUARANTEES HIGH PRODUCTION SPEEDS AT VERY LOW OPERATING PRESSURE) SEAM DETECTOR 2 DYE STUFF TANKS AUXILLARY CHHEMICAL PRODUCT TANK ANALOG DOSING SYSTEM MAGNETIC LEVEL CONTROL LITRE COUNTER HIGH THERMAL GRADIENT HEAT EXCHANGER MICROPROCESSOR FOR COMPLETE TREATMENT CYCLE CONTROL REMOVABLE FILTER MODULAR CONTROL BOARD MAXIMUM FABRIC SPEED 600 MTS/MIN EXTREME VESATILITY OF THIS MACHINE ALLOWS TO PROCESS ANY KIND OF FABRIC (BOTH WOVEN and KNITTED) FROM A WEIGHT OF 50 GRAMS/MT to 800 GRAMS/MT PROGRAMMER APC504 BY AREL NOZZLES 80 to 90mm QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: C-2171 BRAZZOLI HT ROPE DYEING MACHINE, CAPACITY 800 KGS, YEAR 2001 DETAILS: BRAZZOLI 140°C HT ROPE DYEING MACHINE 4.5 BAR LOW LIQUOR RATIO (FROM 1/6 TO 1/8) TYPE SIRIO HT 800 4 TUBES CAPACITY: 800 KGS YEAR: 2001 TURBOVARIO DEVICE VARIABLE BATH PASSAGE CROSS SECTION THAT GUARANTEES HIGH PRODUCTION SPEEDS AT VERY LOW OPERATING PRESSURE SEAM DETECTOR 2 DYE STUFF TANKS AUXILIARY CHEMICAL PRODUCT TANK ANALOG DOSING SYSTEM MAGNETIC LEVEL CONTROL LITRE COUNTER HIGH THERMAL GRADIENT HEAT EXCHANGER MICROPROCESSOR FOR COMPLETE TREATMENT CYCLE CONTROL REMOVABLE FILTER MODULAR CONTROL BOARD MAXIMUM FABRIC SPEED 600 MTS/MIN EXTREME VERSATILITY OF THIS MACHINE ALLOWS TO PROCESS ANY KIND OF FABRIC BOTH WOVEN AND KNITTED FROM A WEIGHT OF 50 GRMS/MT TO 800 GRMS/MT PROGRAMMER APC504 BY AREL NOZZLES: 80 TO 90mm QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: F-1234 NEEDLE PUNCHED NONWOVEN PRODUCTION LINE 4500mm QUANTITY: ONE PRODUCTION LINE Learn More

REFERENCE NUMBER: M-3372 (8808AIFD7RC) K SANTA LUCIA STENTER YEAR 1990 WIDTH 3200mm -OIL HEATED - 5 ZONES - VERTICAL PIN CHAIN SANTA LUCÍA STENTER 3200mm OIL HEATED 5 CHAMBERS VERTICAL PIN CHAIN QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3471 (880OKRSHH7) L NEEDLE PUNCHED NONWOVEN PRODUCTION LINE 4500mm TECHNICAL DATA: RAW MATERIALS: NYLON, POLYESTER, POLYPROPYLENE, GLASS FIBER, ETC. FINENESS OF FIBER: 2.5 TO 10DENIER LENGTH OF FIBER: 38 TO 76mm MIXING RATIO BETWEEN TWO FIBERS: 20 TO 100% SPEED: 6m/min (PER 2.5-6D× 38-51mm) MAX. 5000 KG/DAY (PER 22 HOURS/DAY) RANGE OF GRAM WEIGHT: 100 TO 250g/m2 CARDING MACHINE FEATURES ARE ACCORDING GRAM WEIGHT: 250G/M², 300G/M² PROCESS FLOW CHART: BALE OPENER---PER-OPENER—FINE OPENER--FEEDER---CARDING MACHINE-- CROSSLAPPER--TRANSIT APRON---HIGH-SPEED PRE-NEEDLE LOOM---(2) HIGH-SPEED MAIN NEEDLE LOOM--CALENDER---CUTTER AND REWINDER QUANTITY AVAILABLE: 1 Learn More