Search results for: 'GAS IN'

TT-3153 BRUECKNER FLAT STENTER, WORKING WIDTH 2200mm, YEAR 1990, 6 CHAMBERS, GAS HEATED QUANTITY: 1 Learn More

TT-2817 GENERAL ELECTRIC LM2500 PE SAC GAS TURBINE, 22.5 MW, WITH GE SIX-STAGE PT QUANTITY: 2 Learn More

TT-2292 BRIDGES DRILLING RIGS 1300HP, YEAR 2008 1300 HP BRIDGES DRILLING RIGS DRILLING RIG 1300 HP YEAR 2008 TYPE: USED CONDITION: EXCELLENT QUANTITY: 5 Learn More

TT-2245 NATURAL GAS TURBINE POWER PLANT, 70 MW, YEAR 1996, 50Hz COMPLETE DESALINATION PLANT QUANTITY: 1 Learn More

TT-2196 MWM TCG2032V16 NATURAL GAS GENERATOR SET WITH JACKET WATER COGENERATION, 50Hz, 4.3 MW, YEAR 2011 QUANTITY: 1 Learn More

J-4753 GE FRAME 9E GAS TURBINE GENERATOR UNITS, 109.49 MW TWO UNITS OF FRAME 9E GAS TURBINE GENERATOR UNITS (CONSISTING OF AUXILIARY COMPARTMENT, TURBINE COMPARTMENT, GENERATOR COMPARTMENT) TWO UNITS OF MARK V CONTROL SYSTEM 1 UNIT OF GE STEAM TURBINE GENERATOR UNIT (118.26 MW) (CONSISTING OF AUXILIARY COMPARTMENT, STEAM TURBINE COMPARTMENT, GENERATOR COMPARTMENT) YEAR: 1992 Learn More

TT-1738 HUMMEL LNG CLEAN POWER GENERATING BARGE, 7.5MW, 50 TO 60 Hz, YEAR 2014 THE POWER BARGE WAS ORIGINALLY DEVELOPED TO ENABLE VISITING CRUISE VESSELS TO POWER DOWN MAIN ENGINES IN PORT, REDUCING FUEL USE AND POLLUTION, WHILST RETAINING FULL ELECTRICAL POWER TO ON BOARD SYSTEMS. THE BARGE IS CAPABLE OF GENERATING A TOTAL OF 7.5 MW OF POWER FROM 5 SILENT GENERATORS FED BY TWO 17T LNG CONTAINERS. THE VESSEL IS A FLOATING POWER PLANT PROVIDING CLEAN AND EFFICIENT COLD IRONING POWER TO CRUISE HARBOURS, TERMINALS AND LOCAL INFRASTRUCTURE CURRENTLY. IT CAN ACT AS A BACKUP POWER BANK TO THE LOCAL ELECTRIC AND POWER GRID, ALSO POTENTIALLY PROVIDING HEATED WATER TO LOCAL SYSTEMS. THE POWER BARGE IS CAPABLE OF GENERATING A TOTAL OF 7.5 MW OF POWER FROM 5 SILENT GENERATORS FED BY TWO 17T LNG CONTAINERS. QUANTITY: 1 Learn More

YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS DETAILS: 1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME. 2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE. 3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR. REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK. THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm. 4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM. LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL. 5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS. 6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION. 7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING. QUANTITY: 1 Learn More

REFERENCE NUMBER: YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION DETAILS: MAIN FEATURES: - THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS; - HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS; - CONVEYOR WIDTH: 2200mm; - WORKING WIDTH: 2000mm; - MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C; - HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW; - VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS; - ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS; - INSTALLED ELECTRIC POWER: 200 KW. APPROX.; - MECHANICAL SPEED: 2÷15 METERS PER MINUTE; - CONVEYOR DRIVING: BY A.C. MOTORS; - MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More

YY-1347 PSA OXYGEN GENERATION SYSTEM SCHEME, CAPACITY 50 m3 PER HOUR PURITY: ≥ 93%, FLOW RATE: 50M3 PER H, (PRESSURE: 200 BAR AUTOMATIC FILLING SYSTEM) Learn More