Search results for: 'die pre'

P-5079 COMMERCIAL JOPER CAST IRON CRM-30 ROASTER 30 KILOS

WHAT WE HAVE HERE IS A VERY RUGGED CAST IRON ROASTING FRAME AND ROASTING CONTACT CLEARANCES WITH THE MACHINE - JUST PLAIN SOLID AND DOES NOT MOVE UNDER LONG OR EXTENDED USE. DOUBLE WALL DRUM MEANS THAT THE HEAT IS ALL DESIGNED TO GO THROUGH THE CENTER OF THE ROASTING CHAMBER, NOT "ONTO" THE DRUM EXTERIOR. TOTAL TRUE CONVECTION. NOT ONLY IS THIS THE SAME STYLE FROM THE OLD GOTHOT & BARTH ROASTER DAYS. . . BUT EVEN BETTER AS THE SHAFT DESIGN SO THAT BEARINGS ARE EXTERNALLY MOUNTED AND ADDITIONALLY ARE AIR COOLED FOR LONG LIFE AND TROUBLE-FREE CONTROL. EVEN THE SIDE PANELS OR PRODUCT FLIGHTS HAVE A LONGER CURVE POSITIONING MORE PRODUCT FLOW INTO THE HOT AIR STREAM, RESULTING IN A SLIGHTLY MORE RAPID ROAST WITH MORE EVEN BEAN INTERIOR AND EXPANSION THAT FRANKLY LEADS THE INDUSTRY.

ALL THIS COMMENTARY ABOVE MEANS THIS ROASTER SIMPLY IS MORE QUIET THAN ANYTHING ON THE MARKET. PERIOD. THERMAL INSULATION WITH HIGHEST QUALITY OF FIBER FOR LOW GAS CONSUMPTION; DIGITAL TEMPERATURE CONTROL. CYCLONE IS SEPARATE. THE COOLER, BEING TOTALLY SEPARATE ALSO HAS THE LARGEST AIR COLLECTION AREA OF ANY ROASTER MADE ALLOWING FOR TOTAL AMBIENT COOL COFFEE IN LESS THAN THREE MINUTES. ADD TO THIS PACKAGE A LOADER OR YOUR CHOICE OF DESTONERS AND EVEN YOUR CHOICE OF CONTROL METHODS.

DATA INFORMATION:
BATCH CAPACITY: 30 KG / 66 LBS
CONTROL DESIGN: MANUAL
CAPACITY PER HOUR: 120 KG / 265 LBS
ROASTING TIME: 12-18 MIN (4 BATCHES AN HOUR)
EXHAUST AIR TREATMENT: OPTIONAL
COOLING CYCLONE: OPTIONAL
PRE-COOLING WITH WATER IN DRUM: OPTIONAL
COOLING TIME: 3-4 MIN
TYPE OF COOLING: AIR AMBIENT
SAFETY DEVICE: YES
BURNER POWER: 110 KW / 375000 BTU
BURNERS MANUFACTURER: RIELLO
OPERATION TYPE BURNER: BS2D-2 STAGE
FUEL TYPE: PROPANE/NAUTRAL GAS/DIESEL
SIDE OF OPERATION: LEFT
POWER REQUIREMENTS: 20 AMP
VOLTAGE/FREQUENCY/PHASES: 400+N-230 V / 50-60 HZ / 3 PH
9 AMP. . . 3 PHASE 50/60 HZ PREFERRED, YOUR CHOICE OF 220/440 - SINGLE PHASE AVAILABLE AT SPECIAL REQUEST
(NOTE ON 3 PHASE. . . NOT ONLY IS IT LESS EXPENSIVE TO OPERATE, BUT IT RUNS MORE QUIETLY THAN SINGLE PHASE WHENEVER OR WHEREVER IT IS USED. KEEP THIS IN MIND FOR ANY MACHINERY.)
Ø EXHAUST CHIMNEY (ROASTER CYCLONE): 250MM / 9,8 INCH
Ø EXHAUST CHIMNEY (COOLER): 250MM / 9,8 INCH
Ø HOPPER ROAST CHIMNEY: 150MM / 5,9 INCH
ROASTER WEIGHT WITH CYCLONE: 1050 KG / 2310 LBS
COOLER WEIGHT: 300 KG / 660 LBS
ROASTER FAN MOTOR: 1, 5 HP
COOLER FAN: 4 HP
DRUM GEARBOX: 1 HP
COOLER GEARBOX: 0, 75 HP
BUILT TO UL295 STANDARDS.

QUANTITY: 1

Learn More

P-5072 STA IMPIANTI ROASTER 15 KILOS

ROASTING MACHINES LINE PARTICULARLY SUITABLE FOR ARTISANAL SPECIALIZED ACTIVITIES IN MEDIUM BATCHES OF HIGH-QUALITY ROASTED COFFEE, SUCH AS ARTISAN MARKET OR COFFEE SHOPS. TECHNOLOGICALLY ADVANCED, CONFIRMS THEMELVES AS IDEAL TOOL FOR ROASTING COMPANIES SPECIALIZED IN SELECTED COFFEES OF HIGHER QUALITY. MADE WITH THE SAME REQUIREMENTS FOR RELIABILITY AND SECURITY FEATURES OF THE BIGGER AND MORE SOPHISTICATED INDUSTRIAL ROASTING MACHINES, ARE AVAILABLE WITH HEATING GENERATOR TYPE GAS OR DIESEL-FUEL BURNER AT MULTIPLE LEVELS OF FLAME AND MANUAL OR AUTOMATIC CONTROL SYSTEM.

TECHNICAL DATA:
ROASTER CAPACITY: 15 KG. | MAX. 19 KG./ CYCLE
ROASTING CYCLE: 9 MINUTES ÷ 20
RAW COFFEE PROCESSING PER HOUR: 60 KG. ÷ 90
INSTALLED ELECTRIC POWER: 1,8 KW | 380 VOLT THREEPHASE + NEUTRAL 50 HZ
THERMAL POWER: 24,000 KCAL/H/ 29 KW.
(NATURAL GAS OR LPG)

MAIN COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL
ROASTING DRUM
HEATING GENERATOR OF NEW GENERATION PATENTED AND COMPLETE OF BURNER
RAMP VALVES FOR GAS SAFETY AND ELECTRIC DEVICE TO CHECK FLAMES RATIFIED AND COMPLETE OF ALARM SIGNAL.
COOLING TANK IN STAINLESS STEEL WITH DOOR FOR CLEANING OPERATIONS
SAFETY PREVENTION SYSTEM ON THE COOLING TANK
SUPPORTING FRAME FOR THE OVER INDICATED COMPONENTS
ELECTRIC CONTROL BOARD TO CHECK AND CONTROL THE MACHINE ACCORDING CE RULES, COMPLETE OF PLC + TOUCH SCREEN FOR MACHINE MANAGEMENT AND TEMPERATURES SIGHT.
INDEPENDENT FANS FOR THE ROASTING DRUM AND THE COOLING TANK
INDEPENDENT MOTORS FOR THE ROASTING DRUM AND THE COOLING TANK
CYCLONE FOR CHAFFS COLLECTING

DETAILS OF COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL WITH MANUAL IN-LET OF COFFEE AND DOOR UNLOADING SYSTEM
ROASTING DRUM: MADE BY A FIXED ELEMENT WITH DOUBLE WALLS INSULATED FOR THERMAL PROTECTION AND SUPPORT OF THE ROTATING CYLINDER MOVING THE PRODUCT. SUCH CYLINDER, COMPLETELY MADE IN COMPOUND STEEL TO OVERCOME THE THERMAL CHANGES, IS DEVELOPED WITH A PERFORATED PLATE FOR THE CONTAINMENT AND SPECIAL BLENDERS ON THE RIGHT AND LEFT SIDE PLACED ON DIFFERENT LEVELS TO GET A PERFECT BLENDING OF COFFEE. AT THE END OF THE ROASTING CYCLE, A WIDE DOOR WITH MANUAL OPENING/CLOSING SYSTEM ALLOWS THE PRODUCT UNLOADING.
HEATING GAS GENERATOR OF NEW CONCEPT, PATENTED, COMPLETE OF BURNER, RAMP VALVES FOR GAS SAFETY AND ELECTRONIC EQUIPMENTS FOR FLAME CONTROL RATIFIED AND COMPLETE OF SIGNALLING ALARM (N°2 FLAME LEVELS)
COOLING TANK IN STAINLESS STEEL: WIDE SURFACE PERFORATED WITH 3 ARMS AND CROSSED FLOWS. UNLOADING MOUTH WITH HAND DRIVE.
SUPPORTING FRAME: MONO-BLOCK, PLATE PRESS-BENDED, STEEL MADE, SUPPORTING THE ELEMENTS PREVIOUSLY DESCRIBED.
SAFETY PROTECTION FOR COOLING TANK
ELECTRIC CONTROL BOARD FOR MACHINE MANAGEMENT ACCORDING CE RULES INTEGRATED.
COMPLETE OF PLC + TOUCH SCREEN FOR MACHINE MANAGEMENT AND TEMPERATURES VISUALIZATION.
POSSIBLE RECORDING OF ROASTING PARAMETERS.
CYCLONE FOR CHAFFS COLLECTING
INDEPENDENT MOTORIZATION FOR ROASTING DRUM AND COOLING TANK
INDEPENDENT ELECTRIC-FAN FOR ROASTING DRUM AND ELECTRIC FAN FOR COOLING TANK.

QUANTITY: 1

Learn More

S-1197 LAUNDRY SOAP PRODUCTION LINE, CAPACITY 1000 TO 1500 KG/HR

LAUNDRY SOAP PRODUCTION LINE
CAPACITY: 1000 TO 1500 KG/HR
I. PROJECT INSTRUCTION
THIS PRODUCT LINE IS A SOAP COMPLETE LINE STARTING FROM OIL MELTING, SAPONIFYING, VACUUM DRYING AND COOLING, MILLING SOAP NOODLES, VACUUM EXTRUDING AND THEN CUTTING INTO SOAPS.
THIS PRODUCT LINE HAS ADVANCED TECHNOLOGY INCLUDING COVERING LESS FLOOR AREA, CONSUMING LESS ENERGY, SAVING HUMAN RESOURCES, AUTOMATING PROCESSES, PRODUCING HIGH QUALITY SOAPS WITH 50 TO 80% FATTY ACID CONTENT.
PLEASE NOTICE THAT:
IT IS A TURN-KEY PROJECT. THE PROFESSIONAL TEAM PROVIDE YOU ALL MACHINES AND ACCESSORIES, THE WHOLE PROCESS OF PRODUCTION, FORMULA, LAYOUT DESIGN, MACHINES INSTALLATION, PRODUCTS TRIAL ETC. ALL SOLUTION ACCORDING TO YOUR REQUIREMENTS.
THE QUOTATION INCLUDES ALL EXCEPT: BOILER, WORKSHOP BUILDING, HEAT INSULATING MATERIAL, WIRES, PACKING MACHINE, AND CONSUMABLE MATERIALS FOR INSTALLING (WELDING ROD, CRANE, ELECTRIC WELDER, ETC.).

1. PRODUCTION REQUIREMENTS:
A. STEAM BOILER: 2 MT/HR.
B. WORKSHOP AREA: LARGER THAN 300 M². (L: 35M, W: 7M, H: 7M)
C. POWER: 130 KW, 380 V, 50 HZ.
D. WATER: CIRCULATING WATER FOR VACUUM DRYING SYSTEM: 40 M3; PRODUCTION WATER.
E. CAPACITY: 1000 TO 1500 KG/HR, 8 TO 12 TON/DAY (8 HR/DAY). OIL CONSUMTION: 5 TO 8 TON/DAY.
F. WORKER: 10 TO 12 WORKERS.
2. MATERIAL AND CONSUMING FOR PRODUCING SOAP:
OIL OR FAT OF PLANT OR ANIMAL (PALM OIL, COCONUT OIL, TALLOW OIL, ETC.), CAUSTIC SODA (NAOH), SODIUM-CHLORIDE (NACL), SODIUM SILICATE, FRAGRANCE, PIGMENT, ETC.
3. PRODUCTION PROCESS:
MIX AND MELT OIL --> SAPONIFICATION --> ADD OTHER INGREDIENTS --> VACUUM DRYING --> SOAP NOODLE --> GRINDING --> VACUUM EXTRUDING --> CUTTING.

III. SPECIFICATIONS AND QUOTATION OF EQUIPMENT
1. CARBURETION WORKSHOP:
MIX KINDS OF OIL TOGETHER ON THE BASIS OF THE FORMULA. DEPOSIT AND TAKE OUT THE UNSAPONIFIABLES.

ITEM 001
CARBURETION POOL
MIX KINDS OF OIL TOGETHER ON THE BASIS OF THE FORMULA.
VOLUME: 10 M3.
FIELD WORK
QUANTITY: 1

ITEM 002
STORAGE TANK FOR REFINE OIL
SIZE: Φ2000X2600, 8.2 M3;
FEATURE: WITH COILER INSIDE.
QUANTITY: 1

ITEM 003
WATER PUMP, OIL PUMP, CAUSTIC SODA PUMP
POWER: 1.5 KW/SET.
QUANTITY: 4

ITEM 004
SEAMLESS TUBE
(Φ76X3.5) (Φ57X3.5), ETC.
QUANTITY: SEVERAL

ITEM 005
VALVE
Φ65, Φ40, ETC.
QUANTITY: SEVERAL

ITEM 006
FLANGE, SCREW, ELBOW, GASKET.
QUANTITY: SEVERAL

2. OIL AND FAT SAPONIFICATION WORKSHOP:
OIL AND ALKALI DO REACTIONS IN THE SAPONIFICATION CAULDRONS. IT IS A GOOD COMBINATION OF FOUR SAPONIFICATION CAULDRONS, WATER CIRCULATES FROM NO. 1 CAULDRON TO NO. 4, IT SAVES WATER, NAOH AND NACL AT THE MOST.

ITEM 007
SAPONIFICATION CAULDRON
SAPONIFICATION BETWEEN OIL AND NAOH, LASTING ABOUT 40 TO 60 HRS. SUFFICIENT REACTION. SAVE WATER.
SIZE: Φ2800 X 3000, 20 M3
AUXILIARY FACILITIES: LIQUID CAUSTIC SODA POOL.2 M3
FIELD WORK
QUANTITY: 4

ITEM 008
HIGH TEMPERATURE AND HIGH PRESSURE SOAP PUMP
POWER: 5.5 KW/SET
QUANTITY: 3

ITEM 009
SEAMLESS TUBE
(Φ76X3.5)(Φ57X3.5), ETC.
QUANTITY: SEVERAL

ITEM 010
VALVE
Φ76, Φ48, ETC.
QUANTITY: SEVERAL

ITEM 011
FLANGE, SCREW, ELBOW, GASKET.
QUANTITY: 1

3. SOAP VACUUM DRYING SYSTEM:
TO MAKE SOAP MATERIALS FLASH DRY AND COOL INSTANTLY. TO CONTROL THE FATTY ACID CONTENT FROM 50% TO 80%. TO IMPROVE THE QUALITY OF SOAP MATERIALS.

ITEM 012
INGREDIENTS MIXTURE TANK
PUT ESSENCE, PIGMENT IN THE LIQUID SOAP. HEATING AND MIXING
SIZE: 1.8 M3, Φ1200X1500
FEATURE: WITH PIPE LINER, HEATING AND MIXING
POWER: 4 KW/SET.
QUANTITY: 2

ITEM 013
HEAT EXCHANGER
HEAT THE LIQUID SOAP RAPIDLY
SIZE: Φ325 X 4000
QUANTITY: 1

ITEM 014
VACUUM SPRAY DRYER
THE VACUUM DRYER MAKES THE SOAP FLAKES THINNER AND EVENER, AND COOLS THEM DOWN MORE QUICKLY, TO IMPROVE THE QUALITY OF SOAP NOODLES.
ADOPT HARD TOOTH SURFACE GEAR REDUCER AND THE OIL PUMP INSIDE LUBRICATES AUTOMATICALLY AND MAKES A LONG LIFESPAN. THE THICKNESS OF BARREL IS 14 MM, THE INNER WALL IS PROCESSED BY VERTICAL LATHE TO ACHIEVE THE COAXIALITY AND SMOOTH SURFACE. THE SHAFT IS MADE BY A Φ108 X 14mm SEAMLESS TUBE. THE NOZZLE (Φ10mm) IN THE SHAFT SPRAYS SOAP MATERIALS, AND THE THREE BLADES SCRAPE THEM DOWN, AND THE SOAP MATERIALS DRY OUT FAST AND UNIFORM. THE WHOLE SET OF VACUUM SYSTEM CAN MAKE SOAPS WITH FATTY ACID CONTENT FROM 55% TO 80%.
1. TYPE: XSD-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. BARREL DIAMETER: Φ 1200mm
4. MOUTH DIAMETER: 10mm
5. SPEED: 13 R/MIN
6. POWER: 3 KW
7. DIMENSION: Φ 1600 X 4500mm
8. WEIGHT: 3200 KGS
QUANTITY: 1

ITEM 015
FINE SEPARATORS
SEPARATE THE SOAP POWDER FROM THE WATER WHEN VACUUM DRYING
QUANTITY: 2

ITEM 016
BAROMETRIC CONDENSER
CONDENSE WATER FROM THE SOAP
QUANTITY: 1

ITEM 017
ELIMINATOR
DRAW OFF WATER
QUANTITY: 1

ITEM 018
PELLETIZER
IT IS USED TO PRESS THE VACUUM-DRIED SOAP MATERIALS INTO SOAP NOODLES. LONG DOUBLE SCREWS TURN INWARD TO DRIVE SOAP MATERIALS TO EXTRUDE SOAP NOODLES THROUGH PORE PLATES.
1. TYPE: XSN-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. SCREW DIAMETER: Φ 230mm X 2
4. POWER: 15 KW
5. DIMENSION: 3100 X 1200 X 1550mm
6. WEIGHT: 3000 KGS
QUANTITY: 1

ITEM 019
STAGE VACUUM PUMP
KEEP THE VACUUM SYSTEM IN VACUUM STATE
POWER: 15 KW
QUANTITY: 1

ITEM 020
BUFFER TANK OF VACUUM PUMP
PROTECT THE VACUUM PUMP FROM STEAM WATER
SIZE: Φ600 X1200
QUANTITY: 1

ITEM 021
SOAP PUMP, WATER PUMP
SOAP PUMP: SPECIAL CONSTRUCTURE, DRAW LIQUID SOAP FROM INGREDIENTS MIXURE TANK TO HEAT EXCHANGER. POWER: 7.5 KW
WATER PUMP: FOR WATER CIRCULATING. POWER: 5.5 KW
QUANTITY: 2

ITEM 022
SEAMLESS TUBE AND VALVE
Φ76 Φ48, ECT.
QUANTITY: SEVERAL

ITEM 023
FLANGE, SCREW, ELBOW, ETC.
QUANTITY: SEVERAL

4. FINISHING LINE:
MILL SOAP NOODLES TWICE, VACUUM EXTRUDING SOAP BAR, CUT SOAP CAKES, AT THE SAME TIME STAMP LOGO ON SOAP CAKES.

ITEM 024
THREE-ROLL GRINDING MILL
THREE-ROLL GRINDING MILL IS USED TO GRIND, PRESS THE MATERIAL TO INCREASE ITS DENSITY AND QUALITY.
1. ROLL DIAMETER: Φ260
2. ROLL LENGTH: 780mm
3. MOTOR POWER: 7.5KW
4. ROLL SPEED RATIO: 1:3:9
5. DIMENSION: 1500 X 1200 X 1000mm
6. WEIGHT: 2400 KGS
QUANTITY: 2

ITEM 025
VACUUM PLODDER
VACUUM PLODDER IS USED TO GRIND, REFINE AND PRESS SOAP MATERIAL INTO SOAP BAR. THE ABOVE AND BELOW SCREWS AND TWO ORIFICE PLATES PRESS AND REFINE THE SOAP MATERIAL AND MAKE THE SOAP BAR TIGHT AND THE SURFACE BRIGHT.
THE MOTOR AND THE REDUCER ARE SEPARATED, FOR LONG LIFE-SPAN AND MAINTENANCE. THE BELOW SCREW’ SPEED IS ADJUSTABLE TO REGULATE THE PRODUCTION CAPACITY. THE VACUUM CHAMBER HAS A VISION GLASS TO WATCH THE INNER, THE VACUUM METER TESTS THE VACUUM DEGREE. THE HEATER INSIDE THE OUTLET ADOPT AUTOMATIC TEMPERATURE CONTROL SYSTEM. THE JACKETS OF THE ABOVE AND BELOW BARRELS ARE CONNECTED TO A CIRCULATING WATER SOURCE.
1. TYPE: XS-1000
2. CAPACITY: 1000 TO 1500 KG/HR
3. DIAMETER OF SCREW: Φ230mm
4. SPEED: TOP 15; BOTTOM: 12 TO 18
5. POWER: TOP: 11 KW; BOTTOM: 15 KW
6. DIMENSION: 4350 × 1200 × 2630mm
7. WEIGHT: 4500 KGS
QUANTITY: 1

ITEM 026
ELECTRONIC
CUTTING MACHINE
SOAP ELECTRONIC CUTTING MACHINE IS USED TO CUT SOAPS INTO CAKES AND STAMP PATTERNS ON THE SOAP. ADOPT DELTA SERVO MOTOR AND CONVERTER, VOLTAGE STABILIZER AND PRECISION PURIFIED AC VOLTAGE STABILIZER, TO PROTECT MOTOR AND ELECTRICAL COMPONENTS AND TO KEEP HIGH ACCURACY.
THE MOULD WHEELS RUN BY THE MOVING OF SOAP BAR FROM VACUUM PLODDER. BECAUSE OF THE ELECTRONIC TRACKING SYSTEM, IT CAN CUT SOAP BARS WITH ANY SIZES AND WEIGHT AFTER SETTING THE COMPUTER.
THE CHARACTERS AND THE SHAPE OF SOAP IS CLEAR AND NEAT
THE SIZE AND PATTERN ARE DESIGNED ACCORDING TO CUSTOMERS’ REQUIREMENTS
1. SIZE AND WEIGHT: ADJUSTED BY CUSTOMER’S REQUIREMENTS
2. POWER: 2 KW, 380 V, 50 HZ
3. CAPACITY: IN STEP OF VACUUM PLODDER
4. MOULD: WITH ONE SET
5. DIMENSION: 1000 × 400 × 1200mm
6. WEIGHT: 100 KGS
WOODEN CASE
QUANTITY: 1

ITEM 027
CONVEYORS
APPEARANCE IS GOOD AND OPERATION IS STABLE, NON-NOISE AND ANTI-DUST
MOTOR: 1.1 TO 1.5 KW/PCS
QUANTITY: 4

ITEM 028
VACUUM PUMP
FOR VACUUM PLODDER
POWER: 2.35 KW
QUANTITY: 1

5. OTHERS

ITEM 029
EQUIPMENT SUPPORT, OPERATING PLATFORM, LADDER, ETC.
USED IN CARBURATION POOL, SAPONIFICATION CAULDRONS, AND VACUUM SYSTEM
QUANTITY: 1

ITEM 030
DISTRIBUTION BOX
CONTROL MACHINES, BIG BRAND ELECTRICAL COMPONENTS
WOODEN CASE
QUANTITY: 4

6. ADDITIONAL MACHINES AND SPARE PARTS

ITEM 031
ELECTRICAL CABLES
ALL WIRES FROM EACH MACHINE TO THE FOUR DISTRIBUTION BOXES. THE MAIN WIRE FROM THE FOUR DISTRIBUTION BOXES TO THE MAIN DISTRIBUTION BOX AND SLEEVES ARE NOT INCLUDED
QUANTITY: 1

ITEM 032
HEAT INSULATING MATERIAL
ABOUT 450 M3, INCLUDING GALVANIZED SHEET 450 M3. GLASS WOOL CLOTH, NAILS
QUANTITY: 1

ITEM 033
WELDING ROD
ABOUT 50 BOXES, 1 TON.
QUANTITY: 1

ITEM 034
STEAM BOILER
MATERIAL: DIESEL OIL.
RATED POWER: 2000 KG/H
RATED PRESSURE: 1.25 MPA
RATED STEAM TEMPERATURE: 194 ℃
THE QUOTATION IS FOR ONE WHOLE SET OF BOILER, INCLUDING THE STEAM BOILER, WATER TREATMENT EQUIPMENTS, WATER BOXES, OIL BOXES, PUMPS, AND SOME SPARE PARTS
THE QUOTATION INCLUDES SALARY OF BOILER ENGINEER'S INSTALLATING AND TESTING
THE AIR TICKET AND ACCOMMODATION ARE NOT INCLUDED
LOADED BY A 40 'GP CONTAINER
QUANTITY: 1

QUANTITY: 1 PLANT

Learn More

C-4835 RICE CAKE MACHINES

OFFER 001
MODEL: 8501 (EASY CLEANING)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 1 PC EVERY 10 SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 85 OR 90mm * T: 3 TO 10mm (3 TO 15mm OPTION)
CAPACITY: 360 PCS/HOUR
QUANTITY: 1

OFFER 002
MODEL: 10001
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 1PC EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 100mm * T: 3 TO 12mm (3 TO 15mm OPTION)
CAPACITY: 360 PCS/HOUR
QUANTITY: 1

OFFER 003
MODEL: 6502
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 2PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 65mm * T: 3 TO 12mm (3 TO 15mm OPTION)
CAPACITY: 720 PCS/HOUR
QUANTITY: 1

OFFER 004
MODEL: 4506
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 6PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 45mm * T: 3 TO 12mm
CAPACITY: 2,160 PCS/HOUR
QUANTITY: 1

OFFER 005
MODEL: 2515
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 15PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 25mm * T: 3 TO 12mm
CAPACITY: 5,400PCS/HOUR
QUANTITY: 1

OFFER 006
MODEL: 8585(S1)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 1PC EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 85 OR 90 OR 100mm (SQUARE) * T: 3 TO 12mm
CAPACITY: 360 PCS/HOUR
QUANTITY: 1

OFFER 007
MODEL: 50115(S1)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 1PC EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 50*115mm (RECTANGLE) * T: 3 TO 12mm
CAPACITY: 360 PCS/HOUR
QUANTITY: 1

OFFER 008
MODEL: 6060(S2)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 2PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 60*60mm (SQUARE) * T: 3 TO 12mm
CAPACITY: 720 PCS/HOUR
QUANTITY: 1

OFFER 009
MODEL: 4570(S3)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 3PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 45*70mm (RECTANGLE) * T: 3 TO 12mm
CAPACITY: 1,080 PCS/HOUR
QUANTITY: 1

OFFER 010
MODEL: 2575(S5)
SIZE: 575(L) mm X 470(W) mm X 1,420(H) mm
WEIGHT: 165 KGS
ELECTRIC: 220V / 50 OR 60HZ (1 PHASE 3.5 KW MAX)
ELECTRIC CONSUMPTION: 2KW
WORKING CAPACITY: 5PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 25*75mm (RECTANGLE) * T: 3 TO 12mm
CAPACITY: 1,800 PCS/HOUR
QUANTITY: 1

OFFER 011
MODEL: 4509 (PLC CONTROL)
SIZE: 1,150(L) mm X 460(W) mm X 1,400(H) mm
WEIGHT: 420 KGS
ELECTRIC: 220 TO 380V / 50 OR 60HZ (3 PHASE 6 KW MAX)
HEATER TEMPERATURE: MAX: 400 ℃: MIN: -10 ℃
WORKING CAPACITY: 9PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 45mm* T: 10mm
CAPACITY: 3,240 TO 4,500 PCS/HOUR
QUANTITY: 1

OFFER 012
MODEL: 50115 (S3) (PLC CONTROL)
SIZE: 1,150(L) mm X 460(W) mm X 1,400(H) mm
WEIGHT: 420 KGS
ELECTRIC: 220 TO 380V / 50 OR 60HZ (3 PHASE 6 KW MAX)
HEATER TEMPERATURE: MAX: 400 ℃: MIN: -10 ℃
WORKING CAPACITY: 3 PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 50*115mm (RECTANGLE) * T: 10mm
CAPACITY: 1,080 PCS/HOUR
QUANTITY: 1

OFFER 013
MODEL: 6060(S6) (PLC CONTROL)
SIZE: 1,150(L) mm X 460(W) mm X 1,400(H) mm
WEIGHT: 420 KGS
ELECTRIC: 220 TO 380V / 50 OR 60HZ (3 PHASE 6 KW MAX)
HEATER TEMPERATURE: MAX: 400 ℃: MIN: -10 ℃
WORKING CAPACITY: 6PCS EVERY 10SEC
MATERIAL: 100% OF VARIOUS GRAINS
SIZE OF SNACK: D: 60*60mm (SQUARE) * T: 10mm
CAPACITY: 2,160 PCS/HOUR
QUANTITY: 1

Learn More

C-4227 EREMA RM120TVE FILM/FIBER PELLETIZING LINE, EXTRUDER 120mm, YEAR 2000 - NEW

EREMA PELLETIZING LINE NEW
MODEL: RM120TVE FILM/FIBER
YEAR: 2000
LINE CONSISTS OF THE FOLLOWING:
EREMA MODEL RM120TVE
120mm EXTRUDER WITH 36/1 L/D DOUBLE VENTED BARREL
EXTRUDER IS DRIVEN BY A 160KW AC MOTOR WITH INVERTER
DOUBLE VENT INCLUDES A STAINLESS STEEL DEKER VACUUM PUMP
APPROXIMATELY 50 CUBIC FOOT STAINLESS STEEL CUTTER/COMPACTOR MOUNTED AT FEED SECTION
AND FED BY A 35″ WIDE X 20′ LONG INCLINED BELT CONVEYOR
CUTTER COMPACTOR DRIVEN BY A 105 KW
480 VOLT AC MOTOR

QUANTITY: 1 LINE

Learn More

C-4007 ATOM TRAVELING HEAD PRESS 588-10, CAPACITY 30 TONS

ATOM TRAVELING HEAD PRESS
MODEL: 588-10
30 TON DIE PRESS
10 YEARS OLD

QUANTITY: 1

Learn More

C-3995 MUNCH PELLET MILL SYSTEM, YEAR 2012

MUNCH PELLET MILL SYSTEM
CONSISTING OF:
OFFER 001
VECOPLAN INCLINED FEED CONVEYOR
APPROXIMATELY 60″ WIDE X 26′ LONG

QUANTITY: 1

OFFER 002
ENSIGN DOSING HOPPER
APPROXIMATELY 84″ WIDE X 108″ LONG X 84″ DEEP

QUANTITY: 1

OFFER 003
VECOPLAN INCLINED CONVEYOR TYPE KKF-820-2K-U
APPROXIMATELY 32″ WIDE X 84″ LONG BOTTOM HORIZONTAL SECTION X 30′ LONG INCLINED SECTION

QUANTITY: 1

OFFER 004
ROTARY DRUM MAGNET

QUANTITY: 1

OFFER 005
MUNCH DENSIFIER
APPROXIMATELY 60″ DIAMETER X 60″ DEEP

QUANTITY: 1

OFFER 006
MUNCH RING DIE PELLET MILL
MODEL: RMP660/178
YEAR: 2012

QUANTITY: 1

OFFER 007
FACE ROLLERS
APPROXIMATELY 12-1/2″ DIAMETER X 7-1/8″ FACE ROLLERS

QUANTITY: 2

OFFER 008
VECOPLAN INCLINED CONVEYOR
TYPE: VFB-800-F2
APPROXIMATELY 32″ WIDE X 72″ LONG BOTTOM HORIZONTAL SECTION X 30′ LONG INCLINED SECTION

QUANTITY: 1

OFFER 009
MUNCH PELLET COOLER
MODEL: SDCC10

QUANTITY: 1

OFFER 010
VECOPLAN INCLINED CONVEYOR
TYPE: VFB-800-F2
APPROXIMATELY 32″ WIDE X 120″ LONG BOTTOM HORIZONTAL SECTION X 10′ LONG INCLUDED SECTION

QUANTITY: 1

Learn More

C-3994 BARGEMOUNTED POWER PLANT, CAPACITY 220MW

A. ONCE THROUGH STEAM GENERATOR
B. BARGE
C. CHILLERS
D. AIR COMPRESSOR
E. GAS TURBINE
F. STEAM TURBINE
G. FEEDWATER SYSTEM
H. CLOSED COOLING WATER SYSTEM
I. AUXILIARY COOLING WATER SYSTEM
J. CONDENSATE POLISHING UNIT (CPU)
K. WASTE WATER SYSTEM
L. PLANT ELECTRICAL SYSTEM
M. BLACK START DG SET
N. PLANT CONTROLS AND INSTRUMENTATION
O. PLANT FIRE FIGHTING SYSTEM
P. START UP VACUUM SYSTEM
Q. STEAM TURBINE DEAERATING CONDENSER

QUANTITY: 1 PLANT

Learn More

REFERENCE NUMBER: M-3024 (7703KHDRYN6R) BRUCKNER BOPP LINE 7000mm YEAR 1986 – RECONSTRUCTED 5 LAYER 7000mm BRUCKNER BOPP LINE YEAR 1986 - YEAR OF RECONSTRUCTION: 1996/97/99/2006/12 - CAPACITY CUSTOMER ROLLS (T/A) (1): 18000 (SHD 35-40) - MAXIMUM OUTPUT (KG/HR): 3500 (3) MAXIMUM SPEED (M/MIN) - DESIGN 320 - IN PRODUCTION 270 - FILM WIDTH (TRIMMED) (mm): 7000 - POSSIBLE FILM THICKNESS (MICRON): 20-100 (8) - MAIN FILM: WHITE OPAQUE FILM 3-5 LAYERS MAIN EXTRUDER - TYPE: C - 200/250 (5) - MANUFACTURER: MITSUBISHI CO-EXTRUDER 1) TYPE: KME 75-36 - (OUTER LAYERS) - MANUFACTURER: KRAUS MAFFEI 2) TYPE: KME 75-36 - MANUFACTURER: KRAUS MAFFEI SATELITE EXTRUDER 1) TYPE: E 150 (4) - MANUFACTURER: BARMAG 2) TYPE: KME 1 - 125 (4) - MANUFACTURER: KRAUS MAFFEI DIE - TYPE: 2 X 900/3 LAYER - 1 X 960/5 LAYER - MANUFACTURER: BIG LIFT /EDI COOLING EQUIPMENT: CHILL ROLLS AD = 1800 MM AND WATER BATH (7) MDO: - PREHEATING: LHK (7) - MANUFACTURED: BRÜCKNER ST. TDO - MANUFACTURER: DORNIER - LENGTH PREHEATING (M) 18 - LENGTH STRETCHING (M) 12 - TOTAL LENGTH (M) 51 CHAIN - TYPE: DORNIER (6 ROLLEN) PULL ROLL - TREATMENT: BOTH SIDES - E-CORONA WINDER - MANUFACTURER: KAMPF YEAR OF MANUFACTURE: 2006 GRINDERS - PREFILM MILL - FILM BREAK MILL (INLINE) - 1 OFF LINE FEED MILL (1) SPECIFIC TONS (MAIN TYPE) (3) INCLUSIVE NORMAL CO-EXTRUSION (4) SINGLE SCREW EXTRUDER (5) CASCADE EXTRUDER (6) DOUBLE SCREW EXTRUDER (7) HOECHST DESIGN (8) VOIDED CAN BE SEEN RUNNING AND HAS BEEN MODIFIED A NUMBER OF TIMES SINCE ORIGINAL CONSTRUCTION QUANTITY AVAILABLE: 1 Learn More