REFERENCE NUMBER: Y-2076
TEMPERATURE AND HUMIDITY TEST CHAMBER
THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS.
IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE.
ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS.
SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES.
THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME.
THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER.
DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED.
VOLUME DIMENSION: ABOUT 150L
INTERIOR SIZE: W: 600mm H: 600mm D: 460mm
THE MAIN TECHNICAL PARAMETERS
TEST CONDITION COOL METHOD: AIR COOLED
MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS.
THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT
TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃
TEMPERATURE FLUCTUATION ± 0.5 ℃
TEMPERATURE UNIFORMITY: ≤ 2.0 ℃
TEMPERATURE DEVIATION: ≤ ± 2.0 ℃
TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃
FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD)
COOLING RATE: +20 ℃ TO 40 ℃
FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD)
QUANTITY: 1
Learn More
REFERENCE NUMBER: YY-1365
CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION
DETAILS:
MAIN FEATURES:
- THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS;
- HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS;
- CONVEYOR WIDTH: 2200mm;
- WORKING WIDTH: 2000mm;
- MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C;
- HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW;
- VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS;
- ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS;
- INSTALLED ELECTRIC POWER: 200 KW. APPROX.;
- MECHANICAL SPEED: 2÷15 METERS PER MINUTE;
- CONVEYOR DRIVING: BY A.C. MOTORS;
- MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More
YY-2409 SLOT DIE COATING MACHINE, MAXIMUM COATING WIDTH 1550mm (61 INCHES)
APPLICATION:
1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, FOR COATING, LAMINATION, PEELING, REWINDING FUNCTION.
2. APPLICATION MATERIAL: PET, PVC, PAPER ETC.
MACHINE FEATURES:
1. THIS MACHINE INCLUDES MICROCOMPUTER PLC, TOUCH SCREEN CONTROL, SIMPLE OPERATION AND HIGH AUTOMATION;
2. USING HIGH WEAR-RESISTANT ALLOY STEEL SLOT DIE, WITH COATING CONTROL ACCURACY AND GOOD SERVICE LIFE;
3. AN OVERALL COATING ADJUSTMENT BRACKET IS INCLUDED, AND THE REPEAT POSITIONING ACCURACY IS PRECISE;
4. AUTOMATICALLY TRACKS AND DISPLAYS AND STORES THE AMOUNT OF GLUE NEEDED, MAKING THE OPERATION AND USE CONVENIENT AND FAST;
5. THE FIRST UNWINDING IS EQUIPPED WITH A WEB GUIDING DEVICE, WITH A HIGH-PERFORMANCE INFRARED SENSOR AND ELECTRIC CONTROLLER TO ENSURE THE EVEN LET OFF OF THE MATERIAL ROLL;
6. THE HEATING TEMPERATURE IS ALL CENTRALLY CONTROLLED BY PLC;
7. THE AMOUNT OF GLUE SUPPLIED BY THE METERING PUMP FOR THE COATING WIDTH IS INPUT BY THE WORKER, AND THE AMOUNT OF GLUE SUPPLIED WILL BE AUTOMATICALLY CALCULATED AND SUPPLIED TO THE DIE SLOT.
QUANTITY: 1
Learn More
YY-3279 SGT – 600 GAS TURBINE GENERATOR SET, WITH INTEGRAL LOCAL EQUIPMENT ROOM
UNIT(S) TO BE SUPPLIED ARE UNUSED, WITH ZERO RUNNING HOURS, NEVER INSTALLED.
Learn More
HIGH EFFICIENCY 80 SPRINGS/MIN PS-HX POCKET SPRING MACHINE
ELECTRONICALLY CONTROLLED COILING HEAD
COMPUTERIZED SPRING DIMENSION SETTING SYSTEM
COMPUTERIZED VARIOUS SPRING DATA SAVING SYSTEM
AUTOMATIC POCKET STRINGS CUTTING DEVICE
ACCURATE SERVO SPRING CONVEYOR SYSTEM
INTELLIGENTLY AUTOMATIC ALARM SYSTEM
FLEXIBLE HEAT TREATMENT DEVICE
SMART JOINT DEVICE FOR NON-WOVEN FABRIC ROLL
VARIOUS CUSTOMIZED ULTRASONIC WELDING SEAM
LOW AND EASY MAINTENANCE
SPRING TYPE: BARREL/CYLINDRICAL
AIR CONSUMPTION: APPROXIMATELY 30M3/H
AIR PRESSURE: 0.6 TO 0.7 MPA
POWER CONSUMPTION IN TOTAL APPROXIMATELY 14KW
VOLTAGE: 3AC, 380V – FREQUENCY: 50/60HZ
POWER REQUIREMENTS: INPUT FUSE: 30A – CABLE SECTION: 4 X 10mm2
WORKING TEMPERATURE: +5°C +45°C
WEIGHT APPROXIMATELY 2300KG
SPECIAL OPTIONS, IF DESIRED: ZONING POCKET STRING IS POSSIBLE,
AVAILABLE FOR SPRINGS IN HOUR-GLASS SHAPE, PYRAMID, PPS TYPE AND SO ON
NON-WOVEN FABRIC CONSUMPTION MATERIAL DATA
FABRIC DENSITY: 65~90G/M2
FABRIC WIDTH: 450 TO 600mm
INNER DIAMETER OF FABRIC ROLL MINIMUM 60mm
OUTSIDE DIAMETER OF FABRIC ROLL MAXIMUM 600mm
STEEL WIRE CONSUMPTION MATERIAL DATA
WIRE GAUGE: 1.6 TO 2.1mm
INNER DIAMETER OF WIRE ROLL MINIMUM 320mm
OUTSIDE DIAMETER OF WIRE ROLL MAXIMUM 1000mm
ACCEPTABLE WEIGHT OF WIRE ROLL MAXIMUM 800KG
WORKING RANGE (mm)
STANDARD OPTION 1
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø55~ Ø70
POCKET SPRING HEIGHT: 80~140
STANDARD OPTION 2
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø55~ Ø70
POCKET SPRING HEIGHT: 120~180
STANDARD OPTION 3
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø60~ Ø75
POCKET SPRING HEIGHT: 80~140
STANDARD OPTION 4
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø60~ Ø75
POCKET SPRING HEIGHT: 120~180
STANDARD OPTION 4
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø60~ Ø75
POCKET SPRING HEIGHT: 140~200
SPECIAL OPTION 1
WIRE GAUGE: Ø1.3~ Ø1.6
SPRING WAIST DIAMETER: Ø45~ Ø55
POCKET SPRING HEIGHT: 70~120
SPECIAL OPTION 2
WIRE GAUGE: Ø1.3~ Ø1.6
SPRING WAIST DIAMETER: Ø45~ Ø55
POCKET SPRING HEIGHT: 120~180
SPECIAL OPTION 3
WIRE GAUGE: Ø1.0~ Ø1.4
SPRING WAIST DIAMETER: Ø37~ Ø45
POCKET SPRING HEIGHT: 120~180
SPECIAL OPTION 4
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø50~ Ø60
POCKET SPRING HEIGHT: 180~230
SPECIAL OPTION 5
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø60~ Ø70
POCKET SPRING HEIGHT: 180~230
SPECIAL OPTION 6
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø50~ Ø60
POCKET SPRING HEIGHT: 220~260
SPECIAL OPTION 7
WIRE GAUGE: Ø1.6~ Ø2.1
SPRING WAIST DIAMETER: Ø60~ Ø70
POCKET SPRING HEIGHT: 220~260
Learn More
YY-2761 SLOT DIE COATING MACHINE, WORKING WIDTH 1550mm, FOR HOT MELT PRESSURE SENSITIVE ADHESIVE COATING AND LAMINATION
APPLICATION:
1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, IT HAS FUNCTIONS OF COATING, LAMINATION, PEELING, REWINDING FUNCTION.
2. MATERIAL APPLICATION: PET, PVC, PAPER ETC.
QUANTITY: 1
Learn More
TT-1431 SLOT DIE COATING MACHINE, COATING WIDTH 1600mm
PARAMETERS
1. COATING METHOD: SLOT DIE COATING
2. MAX. COATING WIDTH: 1600mm
3. COATING WEIGHT: 50 TO 300 GSM
4. UNIFORMITY: ≤10%
5. MECHANICAL SPEED: 1 TO 20 METERS PER MINUTE
6. COATING SPEED: THE COATING SPEED IS DETERMINED ACCORDING TO THE COATING WEIGHT, QUANTITY, ADHESIVE VISCOSITY, THE TEMPERATURE AND THE SUBSTRATE.
7. ROLLER WIDTH: 1750mm (ACTUAL WORKING WIDTH OF PAPER ROLL IS 1600mm)
8. MAX. UNWINDING DIAMETER: 1250mm
9. MAX. REWINDING DIAMETER: 950mm
10. UNWINDING TENSION: ≤600N
11. FILM UNWINDING TENSION: ≤200N
12. WINDING TENSION: ≤600N
13. GLUE MELTING SPEED: 310 KG/HOUR
14. GLUE INPUT HOSE: TEFLON TUBE
15. GLUE MELTING TEMPERATURE: ABOUT 260°C MAXIMUM
16. MECHANICAL POWER: ABOUT 40 KW
17. INSTALLED POWER: ABOUT 110 KW
18. POWER SUPPLY: ABOUT 440 VOLTS, 60Hz
19. AIR SOURCE: 0.6 TO 0.8 MPA
20. WATER SOURCE: 0.15 TO 0.4 MPA CIRCULATING COOLING WATER
21. DIMENSIONS: 9000 (LENGTH) X 6600 (WIDTH) X 2300mm
22. THE AMOUNT OF GLUE AND THE GLUE SPEED ARE TRACKED SYNCHRONOUSLY, AND CAN ALSO BE ADJUSTED INDEPENDENTLY
QUANTITY: 1
Learn More
TEMPERATURE AND HUMIDITY TEST CHAMBERREFERENCE NUMBER: Y-2076 TEMPERATURE AND HUMIDITY TEST CHAMBER THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS. IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE. ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS. SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES. THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME. THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER. DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED. VOLUME DIMENSION: ABOUT 150L INTERIOR SIZE: W: 600mm H: 600mm D: 460mm THE MAIN TECHNICAL PARAMETERS TEST CONDITION COOL METHOD: AIR COOLED MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS. THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃ TEMPERATURE FLUCTUATION ± 0.5 ℃ TEMPERATURE UNIFORMITY: ≤ 2.0 ℃ TEMPERATURE DEVIATION: ≤ ± 2.0 ℃ TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃ FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD) COOLING RATE: +20 ℃ TO 40 ℃ FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD) QUANTITY: 1 Learn More
YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATIONREFERENCE NUMBER: YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION DETAILS: MAIN FEATURES: - THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS; - HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS; - CONVEYOR WIDTH: 2200mm; - WORKING WIDTH: 2000mm; - MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C; - HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW; - VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS; - ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS; - INSTALLED ELECTRIC POWER: 200 KW. APPROX.; - MECHANICAL SPEED: 2÷15 METERS PER MINUTE; - CONVEYOR DRIVING: BY A.C. MOTORS; - MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More
YY-2409 SLOT DIE COATING MACHINE, MAXIMUM COATING WIDTH 1550mm (61 INCHES)YY-2409 SLOT DIE COATING MACHINE, MAXIMUM COATING WIDTH 1550mm (61 INCHES) APPLICATION: 1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, FOR COATING, LAMINATION, PEELING, REWINDING FUNCTION. 2. APPLICATION MATERIAL: PET, PVC, PAPER ETC. MACHINE FEATURES: 1. THIS MACHINE INCLUDES MICROCOMPUTER PLC, TOUCH SCREEN CONTROL, SIMPLE OPERATION AND HIGH AUTOMATION; 2. USING HIGH WEAR-RESISTANT ALLOY STEEL SLOT DIE, WITH COATING CONTROL ACCURACY AND GOOD SERVICE LIFE; 3. AN OVERALL COATING ADJUSTMENT BRACKET IS INCLUDED, AND THE REPEAT POSITIONING ACCURACY IS PRECISE; 4. AUTOMATICALLY TRACKS AND DISPLAYS AND STORES THE AMOUNT OF GLUE NEEDED, MAKING THE OPERATION AND USE CONVENIENT AND FAST; 5. THE FIRST UNWINDING IS EQUIPPED WITH A WEB GUIDING DEVICE, WITH A HIGH-PERFORMANCE INFRARED SENSOR AND ELECTRIC CONTROLLER TO ENSURE THE EVEN LET OFF OF THE MATERIAL ROLL; 6. THE HEATING TEMPERATURE IS ALL CENTRALLY CONTROLLED BY PLC; 7. THE AMOUNT OF GLUE SUPPLIED BY THE METERING PUMP FOR THE COATING WIDTH IS INPUT BY THE WORKER, AND THE AMOUNT OF GLUE SUPPLIED WILL BE AUTOMATICALLY CALCULATED AND SUPPLIED TO THE DIE SLOT. QUANTITY: 1 Learn More
YY-3279 SGT – 600 GAS TURBINE GENERATOR SET, WITH INTEGRAL LOCAL EQUIPMENT ROOMYY-3279 SGT – 600 GAS TURBINE GENERATOR SET, WITH INTEGRAL LOCAL EQUIPMENT ROOM UNIT(S) TO BE SUPPLIED ARE UNUSED, WITH ZERO RUNNING HOURS, NEVER INSTALLED. Learn More
TT-2791 SIEMENS SST-400 STEAM TURBINE, 30MW, 10500V, 50HzTT-2791 SIEMENS SST-400 STEAM TURBINE, 30MW, 10500V, 50Hz QUANTITY: 1 Learn More
YY-2761 SLOT DIE COATING MACHINE, WORKING WIDTH 1550mm, FOR HOT MELT PRESSURE SENSITIVE ADHESIVE COATING AND LAMINATIONYY-2761 SLOT DIE COATING MACHINE, WORKING WIDTH 1550mm, FOR HOT MELT PRESSURE SENSITIVE ADHESIVE COATING AND LAMINATION APPLICATION: 1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, IT HAS FUNCTIONS OF COATING, LAMINATION, PEELING, REWINDING FUNCTION. 2. MATERIAL APPLICATION: PET, PVC, PAPER ETC. QUANTITY: 1 Learn More
TT-1431 SLOT DIE COATING MACHINE, COATING WIDTH 1600mmTT-1431 SLOT DIE COATING MACHINE, COATING WIDTH 1600mm PARAMETERS 1. COATING METHOD: SLOT DIE COATING 2. MAX. COATING WIDTH: 1600mm 3. COATING WEIGHT: 50 TO 300 GSM 4. UNIFORMITY: ≤10% 5. MECHANICAL SPEED: 1 TO 20 METERS PER MINUTE 6. COATING SPEED: THE COATING SPEED IS DETERMINED ACCORDING TO THE COATING WEIGHT, QUANTITY, ADHESIVE VISCOSITY, THE TEMPERATURE AND THE SUBSTRATE. 7. ROLLER WIDTH: 1750mm (ACTUAL WORKING WIDTH OF PAPER ROLL IS 1600mm) 8. MAX. UNWINDING DIAMETER: 1250mm 9. MAX. REWINDING DIAMETER: 950mm 10. UNWINDING TENSION: ≤600N 11. FILM UNWINDING TENSION: ≤200N 12. WINDING TENSION: ≤600N 13. GLUE MELTING SPEED: 310 KG/HOUR 14. GLUE INPUT HOSE: TEFLON TUBE 15. GLUE MELTING TEMPERATURE: ABOUT 260°C MAXIMUM 16. MECHANICAL POWER: ABOUT 40 KW 17. INSTALLED POWER: ABOUT 110 KW 18. POWER SUPPLY: ABOUT 440 VOLTS, 60Hz 19. AIR SOURCE: 0.6 TO 0.8 MPA 20. WATER SOURCE: 0.15 TO 0.4 MPA CIRCULATING COOLING WATER 21. DIMENSIONS: 9000 (LENGTH) X 6600 (WIDTH) X 2300mm 22. THE AMOUNT OF GLUE AND THE GLUE SPEED ARE TRACKED SYNCHRONOUSLY, AND CAN ALSO BE ADJUSTED INDEPENDENTLY QUANTITY: 1 Learn More
YY-2544 NEVER USED 2500KW DIESEL GENESET 3 UNITS (MTU, 440V, 60Hz)YY-2544 NEVER USED 2500KW DIESEL GENESET 3 UNITS (MTU, 440V, 60Hz) QUANTITY: 1 Learn More
AA-1120 BASE SHOP COFFEE ROASTERAA-1120 –SALE BASE SHOP COFFEE ROASTER TECHNICAL SPECIFICATIONS: GREEN COFFEE BATCH CAPACITY (MAX): 1.2KG BATCH CAPACITY (MINIMUM ADVISED): 0.5KG CAPACITY PER HOUR: 4KG OPERATION CONTROL TYPE: MANUAL AIRFLOW CONTROL (DAMPER): MANUAL ROASTING TIME: 12 TO 15MIN TEMPERATURE SENSORS: 2 (BEAN AND EXHAUST AIR TEMPERATURE) COOLING TIME: 3MIN TYPE OF COOLING: AIR AMBIENT SAFETY DEVICE: YES OPERATION TYPE BURNER: MANUAL FUEL TYPE: NATURAL GAS(LNG)/PROPANE GAS(LPG) BURNER POWER LPG (G30): LPG 7 TO 23.885KW - BTU/H BURNER POWER LNG (G20): LNG 12 TO 40.945KW - BTU/H INLET PRESSURE LNG: 20MBAR INLET PRESSURE LPG: 37MBAR POWER: 2200W VOLTAGE: 220V/60HZ EXHAUST CHIMNEY (ROASTER CYCLONE): 100mm EXHAUST CHIMNEY (COOLER): 80mm ROASTER FAN MOTOR: 0.33HP COOLER FAN MOTOR: 0.33HP DRUM GEARBOX: 0.17HP COOLER GEARBOX: 170/374HP DIMENSIONS (L X W X H): 1465X940X1180mm NET WEIGHT (ROASTER + CYCLONE): 170KG SHIPPING BOX (L X W X H): 1560X1150X1410mm SHIPPING WEIGHT: 410KG Learn More