Search results for: 'Rate pl'

T-7018 LINE FOR PRODUCING 70 TO 150 DENIER FROM RECYCLED BOTTLES EXTRUDER Φ 160/25 PRODUCT TYPE PET-POY END/POSITION 12 ENDS POSITIONS 24 POSITIONS POSITION/SPINNING BEAM 2 POSITIONS/SPINNING BEAM POSITION DISTANCE (mm) 1500mm SPINNING PACK CYLINDER TYPE, BOTTOM MOUNTED SPINNERET DIAMETER (mm) Φ 90mm CROSS BLOWING AREA 1430mm X 1380mm GEAR PUMP SPECIFICATIONS (CC/REV) 12X3.0CC/REV GEAR PUMP QUANTITY/POSITION 1 OIL PUMP SPECIFICATION (CC/REV) 12X0.12CC/REV OIL PUMP QUANTITY/ POSITION 1 DOWTHERM BOILER/LINE 600L/65KW GUIDE ROLLER SYSTEM (DIAMETER X WIDTH) 160mm X 160mm MIGRATION JET AWA. JAPAN WINDER TWA1800-12ENDS Learn More

REFERENCE NUMBER: Y-2076 TEMPERATURE AND HUMIDITY TEST CHAMBER THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS. IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE. ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS. SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES. THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME. THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER. DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED. VOLUME DIMENSION: ABOUT 150L INTERIOR SIZE: W: 600mm H: 600mm D: 460mm THE MAIN TECHNICAL PARAMETERS TEST CONDITION COOL METHOD: AIR COOLED MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS. THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃ TEMPERATURE FLUCTUATION ± 0.5 ℃ TEMPERATURE UNIFORMITY: ≤ 2.0 ℃ TEMPERATURE DEVIATION: ≤ ± 2.0 ℃ TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃ FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD) COOLING RATE: +20 ℃ TO 40 ℃ FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD) QUANTITY: 1 Learn More

REFERENCE NUMBER: A-2481 ENTRY LEVEL SINGLE NOZZLE ELECTROSPINNING UNIT - STARTER KIT THIS ELECTROSPINNING SYSTEM IS DESIGNED FOR LOW-COST, SMALL-SCALE NANOFIBER RESEARCH, PRODUCING RESULTS FROM A SINGLE-NOZZLE CONFIGURATION IN A COMPACT UNIT. SPINNING DISTANCE, FLOW RATE AND APPLIED VOLTAGE ARE EASILY ADJUSTABLE IN SIDE-BY-SIDE SPINNING SYSTEM. SPECIFICATIONS: SPINNING-TYPE: SIDE BY SIDE SPINNING CHASSIS: ENCLOSED CHASSIS FOR SPINNING AREA COLLECTOR MATERIAL: STAINLESS STEEL TOTAL WEIGHT: APPROX.10 KGS DIMENSIONS: 210 X 170 X 190 mm HIGH VOLTAGE POWER SUPPLY VOLTAGE RANGE: 0 TO 30 KV VOLTAGE PRECISION: 0.1 KV MAX CURRENT: 0.170 MA HIGH PRECISION MICRO PUMP FLOW RATE: 0.01 TO 4464 ML/H (BD 60 ML SYRINGE) FLOW RATE PRECISION: 0.01 ML/H AVAILABLE SYRINGES STANDARD: ALL TYPES ARE AVAILABLE FEEDING AREA DIRECTLY FEED INTO NOZZLE NUMBER OF NOZZLES: 1 NOZZLE NOZZLE MATERIAL: STAINLESS STEEL COMPATIBLE WITH ALL STANDARD SYRINGE NOZZLES SPINNING DISTANCE DISTANCE BETWEEN NOZZLE AND COLLECTOR: 0 TO ∞ DISTANCE ADJUSTMENT METHOD: MANUAL DISTANCE CONTROL STATIONARY PLATE COLLECTOR MATERIAL: STAINLESS STEEL DIMENSIONS OF STATIONARY PLATE: 180 X 300 mm UNIQUE USER INTERFACE 4.3" TOUCH SCREEN CONTROL PANEL WITH WELL DESIGNED USER FRIENDLY INTERFACE FULLY ABLE TO CONTROL ALL PARAMETERS TECHNICAL REQUIREMENTS POWER: 220 VOLTS AND 50/60 HZ @ MAX 25A GROUNDING: EXTERNAL GROUNDING LINE AREA: MIN. 500 X 1000 mm WORKBENCH ABLE TO CARRY MINIMUM 8 KGS. Learn More

REFERENCE NUMBER: A-2480 ENTRY LEVEL SINGLE NOZZLE ELECTROSPINNING UNIT IT IS POSSIBLE TO APPLY HIGH VOLTAGE WITH PRECISION AS WELL AS ADJUST THE FLOW RATE AND THE DISTANCE BETWEEN THE NEEDLE AND COLLECTOR. THE SPINNING AREA IS NOT ENCLOSED IN A CABINET, BUT THE SMALL SIZE OF THE SYSTEM ALLOWS IT TO FIT INSIDE A FUME HOOD. SPECIFICATIONS: SPINNING-TYPE: SIDE BY SIDE SPINNING CHASSIS: ENCLOSED CHASSIS FOR SPINNING AREA FEEDING AREA MATERIAL: PE 1000 (HIGH DENSITY, CHEMICAL RESISTANT) COLLECTOR MATERIAL: 7000 SERIES ALUMINUM ALLOY, STAINLESS STEEL LED ILLUMINATION TOTAL WEIGHT: APPROX.40 KGS DIMENSIONS: 740 X 645 X 410 mm HIGH VOLTAGE POWER SUPPLY VOLTAGE RANGE: 0 TO 30 KV VOLTAGE PRECISION: 0.1 KV MAX CURRENT: 0.170 MA HIGH PRECISION MICRO PUMP FLOW RATE: 0.01 TO 4464 ML/H (BD 60 ML SYRINGE) FLOW RATE PRECISION: 0.01 ML/H AVAILABLE SYRINGES STANDARD: ALL TYPES ARE AVAILABLE FEEDING AREA NUMBER OF NOZZLES: 1 NOZZLE NOZZLE MATERIAL: ELECTRICALLY CONDUCTIVE STAINLESS STEEL NOZZLE INNER DIAMETER: 0.8 mm COMPATIBLE WITH STANDARD SYRINGE NOZZLES MINIMUM REQUIRED SOLUTION FOR SINGLE NOZZLE FEEDING: 2 ML SPINNING DISTANCE DISTANCE BETWEEN NOZZLE AND COLLECTOR: 30 MM - 300 MM DISTANCE ADJUSTMENT: MANUAL CONTROL STATIONARY PLATE COLLECTOR MATERIAL: STAINLESS STEEL DIMENSIONS OF STATIONARY PLATE: 300 X 238.5 mm UNIQUE USER INTERFACE 4.3" TOUCH SCREEN CONTROL PANEL WITH WELL DESIGNED USER FRIENDLY INTERFACE FULLY ABLE TO CONTROL ALL PARAMETERS SAFETY FUNCTION EMERGENCY BUTTON OVER CURRENT PROTECTION TECHNICAL REQUIREMENTS POWER: 220 VOLTS AND 50/60 HZ @ MAX 25A GROUNDING: EXTERNAL GROUNDING LINE AREA: MIN. 1000 X 1000 mm WORKBENCH ABLE TO CARRY MINIMUM 150 KGS. Learn More

REFERENCE NUMBER: M-0180 AUTOMATIC VACUUM PILLOW MACHINE 001E RAW MATERIAL & CASE FABRIC MATERIAL APPLICATION: FOR CONJUGATE HOLLOW SILICONIZED POLYESTER FIBER SHORTER THAN 100mm MICRO FIBER SHORTER THAN 100mm ELASTIC FIBER SHORTER THAN 100mm PILLOW FABRIC QUALITY: PERMEABLE FABRIC LENGTH: 13 METERS LONG QUANTITY AVAILABLE: 1 Learn More

TT-6597 MTU OPEN TYPE NATURAL GAS GENERATORS, 1.5 MW, 50Hz EXCELLENT FULL DESCRIPTION OF A GENERATOR QUANTITY: 10 Learn More

TT-1886 KAWASAKI PU4000B-ER GAS TURBINE POWER PLANT 51.2MW 60Hz, (16 X 3.2MW), YEAR 2008 KAWASAKI PU4000B-ER GAS TURBINE POWER PLANT 51.2MW 60Hz (16 X 3.2MW) MAIN SPECIFICATIONS GAS TURBINE MODEL: M1T-23 BRAND: KAWASAKI POWER OUTPUT: 3,200KWE FREQUENCY & VOLTAGE: 60Hz & 6600V YEAR OF PRODUCTION: 2008 RUNNING HOURS: ABOUT 60 HOURS FUEL OIL: NATURAL GAS PLANT AUXILIARY EQUIPMENT: 1 SET Learn More

TT-4095 SIEMENS SGT 600 GAS TURBINE PLANT, 24.5 MW, 50 Hz, YEAR 2012 TO 2017 MODEL: SGT 600 RATED CAPACITY: 24.5 MW SPEED: 1500 RPM GENERATOR OUTPUT: 11 KV FREQUENCY: 50 Hz AVAILABLE IN SINGLE CYCLE GT1 2012 GT2 2012 GT3 2107 GT4 2017 QUANTITY: 4 UNITS Learn More

REFERENCE NUMBER: E-9990 COMPUTERIZED PILLOW FILLING MACHINE - NEW MODEL: 003-PF WITH OPENING SECTION DIMENSIONS: 5000 X 5000 X 1400mm (16.4 FEET X 16.4 FEET X 55 INCHES) EQUIPMENT: FIBER OPENER 1 PCS; FAN 1 PCS; FILLING LOT 2 SET; PLC CONTROL SYSTEM 1 PCS VOLTAGE: AS PER CUSTOMER'S REQUEST CAPACITY: 150-180KG/H (300 TO 400 LBS/HR) FIBER OPENING RATE: MORE THAN 98% AND NOT BE DAMAGED WEIGHT: 690KG (1500 LBS) PLC (COMPUTER) CONTROL SYSTEM QUANTITY AVAILABLE: 1 Learn More

TT-6753 WARTSILA HFO FIRED POWER PLANT, 119 MW, YEAR 2010 1. WARTSILA 2. 119 MW 3. YEAR 2010 4. BRAND HFO FIRED POWER PLANT 5. COMPRISING OF 7 X 17.55 MW EACH 6. W18V46 HFO FIRED GENERATOR SETS 7. THE ABOVE POWER PLANT IS IN EXCELLENT CONDITION 8. AND CAN BE INSPECTED ON FOUNDATION. 9. CURRENTLY THE PLANT IS BEING OPERATED ON “NO ENERGY, NO PAYMENT” BASIS. QUANTITY: 1 Learn More