Search results for: 'stop bar'

TT-1181 PICANOL AIRJET TERRY PLUS, WORKING WIDTH 2300mm TO 2600mm, YEAR 2008, DOBBY Learn More

TT-1112 EXTRUSION LAMINATOR, UP TO 2200mm, ONE SIDED LAMINATING MACHINE (480 VOLTS, 3-PHASE, 60Hz) MAIN PROCESS AND PARAMETERS TECHNOLOGICAL PROCESS MAIN UNWINDING, RECTIFYING, EXTRUDING, COMPOUND CUTTING AND REWINDING. MAIN TECHNICAL PARAMETERS 1. RAW MATERIAL: SUITABLE FOR COATING RESIN LDPE, PP AND OTHER COATING BASE MATERIAL. 2. AUXILIARY BASE MATERIAL: PAPER, NON-WOVEN FABRIC, ALUMINUM FILM, WOVEN CLOTH AND OTHER APPLICABLE MATERIALS MECHANICAL SPEED: 60 TO 150 METERS/MINUTE (ACTUAL SPEED DEPENDS ON FILM MATERIAL, FILM WIDTH AND THICKNESS, ETC.) EFFECTIVE WIDTH OF LAMINATING: 1200 TO 2000mm LAMINATING THICKNESS: 0.008 TO 0.080mm LAMINATING THICKNESS ERROR ±5% TENSION SETTING RANGE: 20 TO 200 KG/FULL WIDTH CONSTANT TENSION MAXIMUM EXTRUSION: 200 KG/HOUR INNER DIAMETER OF BASE MATERIAL ROLL CORE: 76mm MACHINE POWER: 100 KW ACTUAL OPERATING POWER IS 50 KW TO 60 KW CONTROL TYPE OF COMPOUND SPEED AND LAMINATING THICKNESS: PLC COMPUTER, FULLY AUTOMATIC ELECTRICAL CONTROL LAMINATING WITH EMBOSSING: SINGLE-LAYER Learn More

REFERENCE NUMBER: J-1404

48” PROTEIN BAR (BAR LINE), YEAR 2015

Learn More

REFERENCE NUMBER: M-0467 SULZER TEXTILE LOOMS TYPE G6300 YEAR 2002 WIDTH 2200mm DOBBY SULZER TEXTILE LOOM TYPE G6300 YOC 2002 W.W. 2200 mm WITH ELECTRONIC DOBBY 2670 AT 20 LEVERS INSTALLED LOOM WITH INVERTER EACH LOOM IS SUPPLIED OF: 1.5 BEAMS FL.800 1.5 CLOTH ROLLERS ELECTRONIC LET-OFF ELECTRONIC TAKE-UP WARP STOP-MOTION 6 BARS. 14 HEALD FRAMES 15" WARP STOP-MOTION 6 BARS 4 PREWINDERS HEADS IRO WITH CREEL QUANTITY AVAILABLE: 6 Learn More

SMIT TEXTILE LOOM TYPE GS900 YOC 2005 W.W. 2200mm WITH ELECTRONIC DOBBY 2670 AT 20 LEVERS INSTALLED LOOM WITH INVERTER EACH LOOM IS SUPPLIED OF: 1.5 BEAMS FL.800 1.5 CLOTH ROLLERS ELECTRONIC LET-OFF ELECTRONIC TAKE-UP WARP STOP-MOTION 6 BARS. 14 HEALD FRAMES 15" WARP STOP-MOTION 6 BARS 4 PREWINDERS HEADS IRO WITH CREEL Learn More

TT-3885 WELEX COMPLETE PELLETIZING LINE, 4.5 INCHES DIAMETER VENTED BARREL QUANTITY: 1 Learn More

TT-3883 HPM 24:1 EXTRUDER, 2 1/2″, COMPLETELY REBUILT - CAST FINN HEATERS, BARREL COOLING FANS QUANTITY: 1 Learn More

TT-2680 WELEX EXTRUDER, 2.5" DIAMETER SCREW REBUILT BRAND WELEX CATEGORY EXTRUDERS AND EXTRUSION PLANTS CONDITION USED QUANTITY: 1 Learn More

YY-2424 USED NGR REGRANULATION LINE for BOPP FILM, FLUFF, LUMPS, MDO WASTE 900 TO 1000 KG PER H OVERCONSUMPTION: 500 KW OUTPUT: 1000 KGS PER HOUR INTENDED FOR THE FOLLOWING WASTE: OUTPUT; BOPP FILM, FLUFF, LUMPS, MDO WASTE: 900 TO 1000 KG/H; CPP FILM, FLUFF, LUMPS: 900 TO 1000 KG/H; PERFORMANCE IS PROVIDED FOR REFERENCE ONLY. THE CAPACITY OF THE DEVICE DEPENDS ON THE PROPERTIES OF THE MATERIAL, E.G. MOISTURE CONTENT, PRINTING, WEIGHT, MELT INDEX, CONTAMINATION AND DEGREE OF FILTRATION. AVERAGE POWER CONSUMPTION: 500 KW; AVERAGE COOLING WATER DEMAND: 668 L/MIN; AVERAGE FRESH WATER CONSUMPTION: 34 L/H; MAXIMUM COMPRESSED AIR CONSUMPTION: 100 L/MIN. THE VALUES GIVEN ABOVE ARE ONLY REFERENCE VALUES AND MAY DIFFER FROM THE VALUES FINAL VALUES OBTAINED AFTER CALIBRATION OF THE DEVICE. THIS DATA SHOULD NOT BE USED FOR PLANNING. Learn More

T-9271 2 1/2″ WELEX 24:1 L/D EXTRUDER, REBUILT, GENERAL PURPOSE SCREW, 50 HP MOTOR AND DRIVE 480 VOLT QUANTITY: 1 Learn More