Search results for: 'Hydro'

TT-2177 GAS BASED COMBINED CYCLE POWER PLANT, 116 MW, YEAR 2021 GENERAL ELECTRIC GAS TURBINE GAS TURBINE MODEL NUMBER: GE, 6FAG QUANTITY: 1 Learn More

TT-1746 KAWASAKI HP CENTRIFUGAL GAS COMPRESSOR QUANTITY: 1 Learn More

J-4356 AUTOMATIC NONWOVEN PET PAD PRODUCTION MACHINE - PRODUCTION CAPACITY: 20 PIECES PER MINUTE AUTOMATIC DISPOSABLE NONWOVEN PET PAD PRODUCTION MACHINE USES ULTRASONIC HOT HEATING, CUTTING AND FOLDING REQUIRES 1 OPERATOR CONTROL MODE: RELAY CONTROL MACHINE DIMENSIONS: LENGTH 8500 x WIDTH 1143 x HEIGHT 1880mm VOLTAGE: 220 VOLTS, 60 Hz, 10 AMPS RATED POWER: 12 KW ACTUAL POWER: 2.7 KW ULTRASONIC POWER: 1.5 KW QUANTITY: 1 Learn More

V-1961 AUTOMATIC PET PAD MAKING MACHINE – 400 PADS PER MINUTE – 350KW-480,000 PADS IN 20 HOURS (PER 3-SHIFT DAY, AFTER REMOVING EFFICIENCIES = 500,000 PADS PER 24 HOURS) FULLY AUTOMATIC PET PAD MAKING MACHINE THE MACHINE OPERATORS JOB IS ONLY TO ADD THE RAW MATERIALS AND VERIFY THAT THE MACHINE IS RUNNING PROPERLY. ABSORBENT CORE CRUSH, MIX AND MAKE THE CORE. TOP SHEET, ABSORBENT CORE, BACK SHEET (PE FILM), LAMINATED. FINAL PRODUCTS ARE FOLDED HORIZONTALLY CUTS PAD INTO FINAL SIZE CREATES VERTICAL FOLD MAIN TECHNICAL PARAMETERS: DESIGN SPEED: 300 METERS PER MINUTE (60mm x 90mm) WORKING SPEED: 250 METERS PER MINUTE (60mm x 90mm) QUALIFIED RATE: >98% EFFICIENCY: >85% INSTALLED POWER: 300 KW (MAIN MACHINE) ELECTRICITY: 480 VOLTS, 60 Hz AIR PRESSURE: 0.6 MPA, 2.6 m3 PER MINUTE TOTAL WEIGHT: 65 TONS PRODUCT SIZE: 400mm x 600mm, 600mm x 600mm, 900mm x 600mm, 560mm x 560mm, 4 SIZES, ACCORDING TO ORDER QUANTITY: 1 Learn More

YY-1136 ULTRAVIOLET STERILIZER MAINTENANCE OF UV STERILIZER: 1 CHECK REGULARLY TO ENSURE THE NORMAL OPERATION OF THE UV LAMP. 2. AFTER 9000 HOURS OR ONE YEAR OF CONTINUOUS USE, THE ULTRAVIOLET LAMP SHOULD BE REPLACED. WHEN REPLACING A NEW LAMP, FIRST UNPLUG THE POWER SOCKET OF THE LAMP AND TAKE OUT THE ULTRAVIOLET LAMP. PAY ATTENTION NOT TO TOUCH THE QUARTZ GLASS OF THE NEW LAMP WITH YOUR FINGERS, BECAUSE THE STAIN WILL AFFECT THE INTENSITY OF THE LIGHT, AND CAREFULLY PUT THE LAMP INTO THE CHAMBER OF THE STERILIZER. Learn More

EFFECTIVE WIDTH: 1600mm
DAILY OUTPUT: 10,000 KGS PER DAY
WEIGHT RANGE: 10 TO 150 GSM
FILAMENT DIAMETER: 1.6 TO 2.0 DENIER
SPEED: 350 TO 400 METERS PER MINUTE
RAW MATERIAL: POLYPROPYLENE (PP)
DIMENSIONS: 35,000 X 15,000 X 11,000mm
VOLTAGE: 380 VOLTS, 3 PHASE

CONSISTING OF:

SPUNBOND EQUIPMENT

PP VACUUM SUCTION MACHINE (2)
7800 TO 900 KGS PER HOUR
AIR CAPACITY: 300 CUBIC METERS PER HOUR
POWER: 7.5 KW

MASTER BATCH DOSING UNIT (2)
ACCURACY: 0.01%

EXTRUDER (2)
DIAMETER: 130mm
SINGLE SCREW (2)
HEATING SYSTEM: ELECTRICITY
MOTOR: 75 KW

MELT FILTRATION MACHINE (2)
PIPE SIZE: 50mm
FILTER AREA: 3.5 SQUARE METERS
MELT FLOW: 650 KGS PER HOUR
DOUBLE FILTRATION CHAMBER

MELTING PUMP (2)
40 RPM
FLOW CAPACITY: 400 KGS PER HOUR
POWER: 7.5 KW

SPINNING BEAM (2)
DIMENSIONS: 1900 X 256mm
HANGER TYPE MELT DISTRIBUTION
HEATING SYSTEM: OIL
WORKING TEMPERATURE: 200 TO 260 CELSIUS

SPINNERET (4)
HARDNESS: 30
SIZE: 1900mm LONG X 256mm WIDE
HOLE DIAMETER 0.45mm
HOLE QUANTITY: 6500 HOLE PER METER

QUENCHING UNIT (2)
WORKING TEMP: 20 CELSIUS
AIR FLOW CAPACITY: 12,000 CUBIC METERS/H
AIR PRESSURE: 6500
FILTER SIZE: 80#

FILAMENT DRAFT UNITS (2)
AIR PRESSURE: 5020PA
AIR FLOW CAPACITY: 12,000 CUBIC METERS/H
INSIDE TEMP: 10 TO 25 CELSIUS
FILAMENT FINENESS: 1.6 TO 2.0 DENIER

MELT BLOWN EQUIPMENT

VACUUM SUCTION MACHINE (2)
LOAD CAPACITY: 700 TO 900 KGS PER HOUR
AIR CAPACITY: 300 CUBIC METERS/H
POWER: 7.5 KW

MASTER BATCH DOSING UNIT (2)
4 HOPPERS
200 KGS HOPPER LOAD

EXTRUDER
DIAMETER: 105mm
SINGLE SCREW
MOTOR: 18.5 KW

MELT FILTER
DOUBLE CYLINDER
HYDRAULIC
MELT FLOW CAPACITY: 450 KGS/HR
FILTER SIZE: 150mm DIAMETER
ELECTRIC HEATING

MELTING PUMP
SPEED: 40 RPM
MELT FLOW CAPACITY: 450 KGS PER HOUR
POWER: 7.5 KW

MELT BLOWN DIE SPINNARET
SPINNERET HOLE SIZE: 0.32 TO 0.35mm
HOLE DISTANCE: 40 TO 42 PER INCH
FABRIC WEIGHT: 2 TO 200 GSM

HIGH PRESSURE AIR BLOWER
AIR FLOW CAPACITY: 70 TO 100 CUBIC METERS PER MINUTE
AIR PRESSURE: 100 KPA
POWER: 200 KW

WEB FORMING MACHINE
SPEED: 100 METERS PER MINUTE

ELECTRIC TREATMENT
VOLTAGE: 220 VOLTS, 50 Hz
INPUT CURRENT: 3A
OUTPUT VOLTAGE: 60 KV
TREAT WEB WIDTH: 1.6 METERS

HOT AIR HEATING MACHINE
WORKING TEMP: 350 CELSIUS
PRESSURE: 0.8 KPA
HEATING: ELECTRIC
POWER: 200 KW

THERMAL CALENDER
PROCESSING SPEED: 400 METERS PER MINUTE
ROLLER SIZE: 2000mm LONG, 520mm DIAMETER
EMBOSSING ROLLER: 1
LINEAR PRESSURE: 30 TO 125 N/mm
HEATING SYSTEM: OIL

HYDROPHILIC MACHINE
SPEED: 400 METERS PER MINUTE
FEEDING SYSTEM: DOUBLE KISSING ROLLER
KISS ROLLER DIAMETER: 215mm
LIQUID TANK: 200 KGS WITH HEAT/WARM AND MIX

DRYING SYSTEM:
INFRARED + HOT AIR
DRIVE ROLL SIZE: 150mm
HEATING EQUIPMENT: QUARTZ HEATER, HOT AIR BLOWER, EXHAUST AIR BLOWER

INSPECTION MACHINE
EFFECTIVE WIDTH: 1600mm
INSPECTION SPEED: 400 METERS PER MINUTE
INSPECT GSM: 10 TO 40 GSM

AUTOMATIC WINDING MACHINE
SPEED: 400 METERS PER MINUTE
ROLLER DIAMETER: 2000mm
ROLLER EXCHANGE SYSTEM: AUTOMATIC
FABRIC INSPECTOR: ONLINE
POWER: 15 KW

HIGH SPEED SLITTING MACHINE
PROCESS SPEED: 800 METERS PER MIN
ROLL DIAMETER: MAX 1500mm
SLITTING WIDTH: 80mm
PAPER TUBE SIZE: 76mm DIAMETER
AUTO TENSILE CONTROL: AVAILABLE ONLINE
METER COUNTING: AVAILABLE ONLINE

OIL HEATER (4)
HEATING POWER: 60 KW
MOTOR POWER: 7.5 KW
OIL PUMP FLOW: 30 CUBIC METERS PER SECOND
PRESSURE: 0.4 KPA

WATER CHILLER
DRIVE SYSTEM: SCREW
COOLING CAPACITY: 300,000 CALORIES
TEMP: 0 TO 20 CELSIUS
POWER: 110 KW

AIR BLOWER
SPEED: 1450 RPM
AIR BLOW CAPACITY: 12,000 CUBIC METERS PER HOUR
PRESSURE: 5200 PA
POWER: 30 KW x 3, 45 KW x 1

AIR COMPRESSOR
DRIVE SYSTEM: SCREW
PRESSURE: 0.8 KPA
POWER: 15 KW

HEATING SYSTEM: ELECTRIC
TEMP: 350 CELSIUS
HEATING TIME: 6 TO 8 HOURS
POWER: 4 KW

ULTRASONIC CLEANING MACHINE
3mm THICK
SIZE: 2000 X 500mm
FREQUENCY VIBRATION: 100 KHZ
TEMP: 40 CELSIUS

ELECTRONIC PANEL BOARD

PLATFORM

Learn More

REFERENCE NUMBER: L-5536

OIL REFINERY, 105,000 BPD FOR LIGHT TO HEAVY CRUDE OILS

 

105,000 BPD

COMMISSIONED IN THE 1970s AND HAD A CAPACITY OF 155,000 BPD

NOW CONVERTED TO AN ATMOSPHERIC/VACUUM DISTILLATION REFINERY WITH FCC CAPABILITIES

DESIGNED TO PROCESS LIGHT TO HEAVY CRUDE OILS

CAN PROCESS CRUDE OIL WITH AN API RANGE OF 19 TO 44 (INCLUDING CASTILLA, HAMACA, EL SHARARA, CPC, AND SAHARA BLENDS)

 

QUANTITY: 1

Learn More

R-

66

76

DEMAG CHALLENGER 3180 CRANE, CAPACITY 60 TONS, YEAR 2012

TEREX CHALLENGER 3180

LIFTING CAPACITY: 60TN

CRANE MODEL: DEMAG CHALLENGER 3180

YEAR

:

2012

Learn More

R-

66

75

GROVE GMK 3055 CRANE, CAPACITY 55 TONS, YEAR 2007

GROVE GMK 3055

LIFTING CAPACITY: 55 TONS

CRANE MODEL: GROVE GMK 3055

YEAR

:

2007

Learn More

M-6262 RF SYSTEMS TD-85 RADIO FREQUENCY DRYER FOR CONES YEAR 2002

RADIO FREQUENCY DRYER FOR CONES
MAKE: RF SYSTEMS
MODEL: TD-85 (K85)
YEAR: 2002
THREE PHASES 380 – 50 HZ
FOR DIFFERENT VOLTAGE THE MACHINE IS EQUIPPED WITH AUTO TRANSFORMER
THE NOMINAL VOLTAGE SHOULD BE WITHIN 5% (TEMPORARY EXCURSIONS OF +5% AND -5% ARE PERMITTED) OTHERWISE CUSTOMER MUST INSTALL A SUITABLE STABILIZER
MAXIMUM POWER ABSORBED FROM THE MAINS: 130 KVA
MAXIMUM CURRENT ABSORBED: 210 A
GAUGE WIRE: 3x75mm2 + GROUND 50mm2 MINIMUM

GENERATOR
MAXIMUM POWER RADIO FREQUENCY GENERATOR: 85 KW (1 x 85KW)
WORK FREQUENCY: 27 MHZ
COOLING SYSTEM: FORCED AIR
MAXIMUM ROOM TEMPERATURE: TA = 35°C IF HIGHER POWER MUST BE REDUCED
MAXIMUM EXHAUST AIR TEMPERATURE: TU = 85°C
OSCILLATOR: CAVITY TYPE WITH HIGH OVERALL EFFICIENCY
FREQUENCY STABILITY: WITHIN LIMITS
RADIATED FIELD: WITHIN LIMITS
GRID CURRENT WITH NO LOAD: 2.3 A TO 2.5 A
GRID CURRENT MINIMUM WITH FULL LOAD: 1.4 A
TRIODE TYPE: RS 3060 CL
FILAMENT TRIODE VOLTAGE: 10 V + 1% - 3%

BELT – CONVEYOR
MATERIAL: POLYESTER FABRIC
TRACKING: AUTOMATIC
LENGTH: 21600mm
WIDTH: 1750mm
RANGE OF CONVEYOR SPEED: 0 TO 50 M/ORA
ELECTRODE: STANDARD TYPE

PRODUCTIVITY
MAXIMUM EVAPORATING CAPACITY: 90 KG WATER PER HOUR

DIMENSIONS
LENGTH: 9600mm
WIDTH: 2124mm
MAXIMUM HEIGHT: 3400mm
GALLERY LENGTH: 4000mm
INLET LENGTH: 2800mm
OUTLET LENGTH: 2800mm
BELT WIDTH: 1750mm
LOAD HEIGHT: 900mm
MAXIMUM HEIGHT OF INLET TRAP: 300mm

THE DRYER TD85 IS COMPOSED OF ONE UNITY OF 85 KW

SPECIAL REQUIREMENTS ON USING RADIO FREQUENCY DRYER
THE DRYER CAN ACCEPT ONLY HYDROEXTRACT GOODS WITH EVEN MOISTURE CONTENT
POSSIBLE FIRE HAZARD WHEN DEALING WITH UNEXTRACTED PACKAGES
PROPEN HYDROEXTRACTION IS IMPORTANT PRIOR TO RF DRYER
LOAD PRODUCT WITH SAME DIMENSIONS AND SIMILAR MOISTURE CONTENTS
PACKAGE PLACEMENT ON THE BELT. ANY TYPE OF TUBE MAY BE USED IN A CONTINUED RF DRYER
METAL TUBES REQUIRE MOVE CARE IN PLACEMENT ON THE BELT THEN PLASTIC TUBE
METAL TUBES CAN CAUSE SHORT CIRCUITY, OR ARCING, FROM ONE ELECTRODE TO GROUND, WHICH CAN DAMAGE THE BELT OR CAUSE FIRE
PACKAGE WITH METAL TUBES MUST BE PLACED ON THE BELT SO THE METAL IS PARALLEL TO THE ELECTRODES AS SHONS IS TY
THE CONVEYOR SHOULD ALWAYS BE LOADED EVENLY, WITH NO BIG EMPTY GAPS
LOAD AS MUCH AS YOU CAN
GOOD WITH DIFFERENTS SIZE ARE NOT ALLOWED THEY CAN GET BURNS
LOAD A QUANTITY OF GOODS WITH A QUANTITY OF WATER TO REMOVE PER LINEAR METER OF BELT AROUND 5 TO 15 KG PER LINEAR METER OF BELT
THE MACHINE CANNOT ACCEPT METALLIC DYSTUFF (EX.CHROME)
DO NOT ENTER METALLIC PARTS
METALLIC IN THE GALLERY CAUSES ELECTRICAL DISCHARGES WHICH MAY THOROUGHLY RUIN BELT AND SET THE DRYING MATERIAL ON FIRE

QUANTITY: 1

Learn More