Search results for: 'panel'[0]'

T-9183 BARMAG FDY LINE 2, CAPACITY 3,250 TO 4,600 KG/DAY, YEAR 1998 -WITH 17 SETS BARMAG CW WINDER, 6 END, 920mm CHUCK = 102 THREAD LINES 50-70 DENIER MACHINE IS CAPACITY 3,250 TO 4,600 KG/DAY YEAR 1998 Learn More

T-9182 BARMAG FDY LINE 1, CAPACITY 3,250 TO 4,600 KG/DAY, YEAR 1998 -WITH 17 SETS BARMAG CW WINDER, 6 ENDS, 920mm CHUCK = 102 THREAD LINES FDY LINE 1 50-70 DENIER MACHINE IS CAPACITY 3,250 TO 4,600 KG/DAY YEAR 1998 Learn More

REFERENCE NUMBER: M-2042 (770IDFGXX6) WISCONSIN OVEN GAS FIRED BATCH OVEN FOR TEMPERING MATTRESS INNERSPRINGS GAS FIRED BATCH OVEN MANUFACTURER: WISCONSIN OVEN STILL ASSEMBLED TODAY OVEN WILL BE USED FOR TEMPERING STEEL SPRING ASSEMBLIES WITH A LOADING OF APPROXIMATELY 50 ASSEMBLIES WEIGHING APPROXIMATELY 40 POUNDS, IN THE OVEN AT A TIME THE SIZE IS BASED ON APPROXIMATELY 4 TO 5 CYCLES PER HOUR PROVIDING THE LOADING AND UNLOADING IS ACCOMPLISHED PROMPTLY THE HEATING RATE IS BASED ON A HEATING CYCLE OF APPROXIMATELY 12 MINUTES PER CYCLE THE OVEN WILL INCLUDE, BUT NOT BE LIMITED TO, THE DEISNG FEATURES OUTLINED IN OUR SPECIFICATIONS LISTED BELOW FURTHER MODIFICATIONS AND DESIGN CHANGES MAY BE INCORPORATED AT THE FINAL ENGINEERING STAGES TO PRODUCE THE BEST EQUIPMENT POSSIBLE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-0180 AUTOMATIC VACUUM PILLOW MACHINE 001E RAW MATERIAL & CASE FABRIC MATERIAL APPLICATION: FOR CONJUGATE HOLLOW SILICONIZED POLYESTER FIBER SHORTER THAN 100mm MICRO FIBER SHORTER THAN 100mm ELASTIC FIBER SHORTER THAN 100mm PILLOW FABRIC QUALITY: PERMEABLE FABRIC LENGTH: 13 METERS LONG QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5321 (22011DGFAB1RXL) L JENBACHER NATURAL GAS POWERPLANT 21.6 MW YEAR 1998 COMPLETE JENBACHER NATURAL GAS POWERPLANT OF 21.6 MW YEAR OF MANUFACTURE END OF 1998 COMMISSIONING: 5 UNITS IN 2000, 1 UNIT IN 2009, 1 UNIT IN 2010, AND 1 UNIT IN 2011 8 UNITS JENBACHER JMS 620 G OF 2.7 MWE-TOTAL EFFECTIVE ELECTRIC OUTPUT 21.7 MW RUNNING HOURS: 5 UNITS BETWEEN 38,000 AND 40,000 HOURS, 2 UNITS 6,200 HOURS AND 1 UNIT 7,200 HOURS JENBACHER MAINTENANCE FULL MAINTENANCE HISTORY QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4558 (1111185AP10RC) L DORNIER HTVS 4/S RAPIER LOOMS YEAR 1997 WIDTH 2000mm DORNIER RAPIER LOOMS TYPE HTVS 4/S YEAR 1997 WIDTH 2000mm NOMINAL WIDTH 2000mm 8 WEFT COLORS MAXIMUM CAPACITY AT-1 CONTROL PANEL ELECTRONIC STAUBLI DOBBY 2671 – 20 SHAFT CAPACITY – 16 TO 20 SHAFTS INSTALLED ECT – ELECTRONIC TAKE UP, EWL – ELECTRONIC WARP LET-OFF, ECS – ELECTRONIC COLOR SELECTOR QUANTITY AVAILABLE: 20 Learn More

REFERENCE NUMBER: M-4796 (11111575DJQ10RX) L COMPLETE BREWERY 65HL INCLUDING FILLING LINES AND KEG LINE DELIVERY OF ONE 65 HL BREWERY WITH THE FOLLOWING EQUIPMENT: 1. MALT HANDLING - MALT ACCEPTANCE BY BIG PACKS - MALT ELEVATOR TO CONDITIONING TANK - GRIST CASE - MALT MILL, MAKE STEINECKER, TYPE: MAISCHOMAT 3003, WET MALT MILL, BUILT 1997 2. BREWHOUSE EQUIPMENT 3-KETTLE-STEINECKER-BREWHOUSE WITH 65 HL CAST WORT, COMPLETE IN STAINLESS STEEL, DRIVES FROM BELOW, AUTOMATED, WITH SIEMENS S5 CONTROL, BUILT 1997 - MASH TUN WITH MASHING FROM BELOW, BOTTOM HEATING ZONE, MASH PUMP, Ø: ~2.500mm - LAUTERTUN, WITH 2-ARM RAKING MACHINE, STAINLESS STEEL KNIFES, 6-PARTED STAINLESS STEEL FALSE BOTTOM, RING LAUTERIG, FALSE BOTTOM RINSING, SPENT GRAINS FALL PIPE, FLOW METER, LAUTER PUMP, Ø: ~2.500mm - WORT KETTLE / WHIRLPOOL, WITH INTERNAL COLANDRIA, WITH TANGENTIAL INLET, SPRAYBALL, WORT PUMP, ~2.500mm - AUTOMATED CONTROL OVER PC FOR BREWHOUSE UNTIL FERMENTING CELLAR AND CIP - ELECTRICAL CONTROL CABINETS - STEEL CONSTRUCTION BETWEEN THE VESSELS - HOT WATER TANK, 200 HL CONTENT, IN STAINLESS STEEL, ISOLATED, HORIZONTAL, STEAM HEATED, WITH MANWAY, MEASUREMENTS: Ø: 2.400 mm x L: 5.700 mm x H: 2.800 mm, WITH PLATE HEAT EXCHANGER, FREQUENCY CONTROLLED PUMP, CONTROL CABINET - COLD WATER TANK, HORIZONTAL, ~150 HL CONTENT, IN STAINLESS STEEL, ISOLATED, WITH MANWAY, MEASUREMENTS: Ø: 2.300mm x L: 4.000mm x H: 2.400mm, WITH PLATE HEAT EXCHANGER, PUMP, CONTROL CABINET - 1 CIP-TUB 3. WORT COOLING - WORT COOLER, MAKE SONDEX, TYPE: S38-FG, 1-STAGE, FOR ICE WATER, 6 BAR, 0,130°C, FLOW METER, BUILT 1998 - WORT AERATION 4. FERMENTING- + STORAGE CELLAR - 9 CYLINDER-CONICAL FERMENTING- AND STORAGE TANKS, INDOOR-CCTS, MAKE HOLVRIEKA, WITH EACH 300 HL GROSS CONTENT, 0,99 BAR, STANDING ON 4 FEET, WITH 3 COOLING ZONES 2 OF THEM IN THE WALL AND 1 CONE COOLING ZONE, WALL ISOLATED WITH PU-FOAM WITHOUT COVERING, CONE ISOLATED AND COVERED, WITH SCANDI BREW ARMATURES, SAMPLER, CLEAR AND REST OUTLET, HEIGHT: ~ 7.500mm, Ø: ~2.900mm, BUILT 1997 - 2-TANK-CIP-PLANT, AUTOMATED, ONLY FOR THE CCTS, IN STAINLESS STEEL, WITH LID, LEVEL DISPLAY, PIPING, PUMP, AUTOMATIC APV VALVES - 2 PANEL, WITH SWIVELLING BOWS - PUMPS - CARLSBERG FLASK FOR YEAST PROPAGATION FROM SCANDI BREW - 1 YEAST TUB, ABOUT 100 LT, IN STAINLESS STEEL, WITH LID, AS TRANSFER TUB - YEAST PUMP, MOBILE 5.1 FILTERCELLAR 100 HL/H - KIESELGUHRFILTER, MAKE SCHENK, TYPE: ZHF-S25, FOR 100 – 125 HL/H WITH OPERATING PLATFORM, HYDRAULIC DRIVE, HYDRAULIC AGGREGATE, STANDING ON BASIS FRAME, BUILT 1989, GRATING, CONTROL CABINET - KIESELGUHR DOSAGE, WITH AGITATOR, LID, DOSAGE PUMPE, PRECOATING PUMP - DOSAGE TUB WITH AGITATOR AND PUMP, MOBILE, WITH PLUG - ROOM AIR EVAPORATOR WITH 2 FAN 5.2 BBT CELLAR - 3 STAINLESS STEEL BRIGHT BEER TANKS / BBTS, MAKE HOLVRIEKA, EACH 140 HL, 1 TANK WITH 1,5 BAR, 2 OF THEM WITH 1,0 BAR BUILT 1997, MOULDED BOTTOM TANKS, NOT COOLABLE, STANDING ON 4 FEET, WITH MANWAY, SPRAY HEAD, PULLED DOWN CLEANING PIPE, SAMPLER, MANOMETER, Ø: 1.500 mm, BUILT 1998 - BEER PUMP - PANEL, MAKE PALL - 1 CIP-TUB, MANUAL, WITHOUT LID, STANDING ON 3 FEET, ~100 LT CONTENT, PUMP - CO2 MEASURING UNIT MAKE HAFFMANS, MOBILE 6. COMBINATED BOTTLING LINE, NON RETURNABLE BOTTLES AND CANNING LINE FILLING LINE FOR NON RETURNABLE GLASS BOTTLES FOR 0,275 LT, 0,33 LT 0,5 LT AND 0,75 LT BOTTLES WITH CROWN CAPS OR SCREW CAPS: - NEW GLASS AND CANS DEPALLETIZER, MAKE KÖNIG, TYPE: M-0-00.5086/1, CHUTE MACHINE, BUILT 2000, IN OPERATING FOR THE GLASS LINE AND THE CANNING LINE (INTERIM LAYER LIFT OFF IS OUT OF OPERATION - LINEAR-RINSER, MAKE SFT STEINLE FÖRDERTECHNIK AUGSBURG, INLET AT TOP, OUTLET BELOW, FREQUENCY CONTROLLED, COMPLETE IN STAINLESS STEEL, BUILT 1997 - METAL INSPECTION, MAKE HEUFT - BOTTLE FILLER, MAKE H+K/KHS, TYPE: VVF 80/12/12, SINGLE PRE-EVACUATION, REBUILT IN 1997 FROM HORMES, WITH CROWN CAPPER AND SCREW CAPPER FOR PLASTIC CAPS, VACUUM PUMP, BEER REGULATION LINE, HDE, LEFT->RIGHT - FILL HEIGHT INSPECTING, MAKE HEUFT, TYPE: BASIC, BUILT 2003 - LABELER, MAKE CAVAGNINO & GATTI, FOR 10.000 BPH, FOR SELF-ADHESIVE LABEL WITH 3 AGGREGATE FOR FRONT-, BACK- AND NECK LABEL, BUILT 2009, WITH FREE STANDING CONTROL DESK - CAP SET UP - TRAY-ERECTOR, MAKE KETTNER, BUILT 1994 - SHRINK PACKER, MAKE DOBOY, TYPE: SW 83-D, BUILT 1980 - FLASH PASTEURIZER, MAKE ALFA LAVAL, TYPE: N-35, FOR 100 HL/H, 3-STAGE, WITH BACK COOLING ZONE, HOT HOLDING ZONE, BUILT 2005 - CHAMBER PASTEURIZER, MAKE RICO, FOR 2 PALLET, COMPLETE OVERHAULED IN 2003 - 1 CIP-TUB 7. CANNING LINE FOR 250 ML SLIM-LINE CANS FOR BEER AND CARBONATED SOFTDRINKS, FORMAT PARTS FOR 330/500 LT CANS TYPE 202, PARTLY EXISTING: - RINSER, MAKE TRANS TECH HYSEK, TYPE: CANJET 2575, 2-CHANNEL RINSER WITH CAN TURNER AFTER THE RINSER, BUILT 2000 - FILLER, MAKE NOLL (KHS), WITH 16 FILLING VALVES, UNDERCOVER GASSING, BUILT 1982 - SEAMER, MAKE FERRUM, TYPE: F160, WITH 6 HEADS, BUILT 1981 - FILL HEIGHT INSPECTION, MAKE HEUFT, TYPE: BASIC, BUILT 2005 - CAN WARMER / PASTEURIZER, MAKE ENZINGER, TYPE: PS 4500, WITH 3 ZONES, IN STAINLESS STEEL, WITH EDELSTAHL, WITH WIRE HOOP HINGE BELT, BUILT 1982 - MULTIPACKER, MAKE SMI, TYPE: MP 100 RD, FOR 4/6 PACKS WITH CARDBOARD - „AIR-KNIFE“, MAKE SONIC SYSTEMS - CONVEYORS 8. KEG-WASHER/FILLER KEG-PLANT MAKE MALEK MB KEG TECHNOLOGIE, TYPE: TWIN 3, WITH 2 HEADS, 1 X CLEANING HEAD AND 1 X FILLING HEAD, PRESSING FROM TOP, CURRENTLY TRIANGULAR FITTING, 3 MEDIA FILTER, WITH 1 DETERGENT TUB, BUILT 2003 9. SYRUP ROOM - SUGAR DISSOLVING TANK, IN STAINLESS STEEL, WITH AGITATOR - 5 MIXING TANKS, STAINLESS STEEL, DIFFERENT CONTENTS, OF THEM 1 LYING TANK 8 HL ISOLATED - PREMIXER, MAKE HORMES, FOR 200 HL/H, REBUILD IN 1997 FROM HORMES - PLATE FILTER, MAKE STRASSBURGER, 40X40, WITH 45 PLASTIC PLATES - BAG FILTER - 3 PUMPS: MONO PUMP, MOBILE PUMP WITH SWITCH 10. BAG-IN-BOX-FILLING AUTOMATIC BIB-PLANT WITH: - CARTON ERECTOR, MAKE CERMEX - FILLER, MAKE SMURFIT - CARTON CLOSER, MAKE CERMEX - MANUAL BIB-FILLER, MAKE ALFA LAVAL, TYPE: PICCOLO, BUILT 2011 11. APPLE / BERRY JUICE PRODUCTION - APPLE CRUSHER, MAKE VORAN, BUILT 2011 - BERRY CRUSHER, MAKE BUCHER, BUILT 2011 - APPLE PRESS, MAKE BUCHER, TYPE: XPLUS 40 M, BUILT 2011 - HOLDING TANK - PUMPS - 2 STORAGE TANKS FOR JUICE IN STAINLESS STEEL, EACH 30.000 LT, WITH AGITATOR, NON-PRESSURE 12. TECHNICAL UNITS 12.1 COLD SUPPLY - GLYCOL COOLING, MAKE CARRIER, WITH 2 COMPRESSORS, R22, BUILT 1997 - WATER COOLED CONDENSER, BUILT 1997 12.2 STEAM SUPPLY - STEAM KETTLE, FOR 2 TO. STEAM/H, 12 BAR, WITH WEIßHAUPT-GAS-BURNER, CONDENSATE-TANK AND CHIMNEY, BUILT 1997 13. LABORATORY EQUIPMENT - BEER ANALYSER, MAKE ANTON PAAR, TYPE: SP-1 AUTO SAMPLER - TURBIDMETER - O2 IN HEADSPACE CONTROL MAKE ZAHM & NAGEL - CO2 MEASURING, MAKE HAFFMANS, TYPE: GEHALTEMETER 14. OTHERS - PALLETIZER, MAKE KETTNER, FOR TRAYS ON EURO-PALLET, COMPLETELY OVERHAULED, NOT USED - STERILE FILTER, MAKE PALL, TYPE: CFS, FOR 100 HL/H, NOT IN USE, BUILT 1998 - VARIOUS NEW AND NOT USED CONVEYORS - VARIOUS CARTRIDGE FILTERS - VARIOUS PUMPS - CARLSBERG-FLASK FOR YEAST PROPAGATION - VARIOUS SMALL TANKS QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4747 (1111NBRTHH10) L INDUSTRIAL BREWERY WITH BREWHOUSE 20 HL INDUSTRIAL BREWERY WITH CAPACITY OF 20 HL PER BREW YEAR PRODUCTIVITY OF 6,000 TO 7,000 HL, 3 SORTS OF BEER BREWERY IS NOT LOCATED AT A SEISMIC AREA EQUIPMENT DESIGNED ACCORDING TO EUROPEAN STANDARD STEAM HEATED 2-VESSEL BREW HOUSE OF 20 HECTOLITRES IN STAINLESS STEEL SCOPE OF SUPPLY: MALT MILL 1 X 2-ROLL MILL WITH CAPACITY OF 400 TO 800 KG/H WITH INLET FROM THE TOP FOR MALT SACKS BREW HOUSE 20HL STEAM HEATED STAINLESS STEEL 1.1 MASH/WORTH – KETTLE DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 LLC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL 2 STEAM HEATING ZONES (BOTTOM AND CYLINDRICAL PART) AGITATOR AND SHAFT IN STAINLESS STEEL, MATERIAL 1.4301. INSTALLATION OF BOTTOM CENTER. DRIVE VIA GEAR MOTOR, SPEED CONTROLLABLE BY FREQUENCY CONVERTER 1 SPRAY BALL 1 MAN HOLE WITH GLASS 1 PRESSURE RELIEF VALVE – SAFETY VALVE 1 LEVELMEASUREMENT DESIGNED FOR NON PRESSURE OPERATION 1.2 LAUTER TUN DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL ISOLATION OF THE CYLINDRICAL PART AND THE BOTTOM - 100 MM HALOGEN-FREE MINERAL WOOL. BOTTOM OF THE LAUTER TUN WITH OUTLET VALVES, BACK WASH VALVES AND A DRAIN VALVE MULTIPART SIEVE PLATE 1.4301 REMOVABLE THROUGH MANHOLE. HOEING 1.4301 TWO-ARMED WITH KNIVES AND TREBERN SWORD. INSTALLATION OF BOTTOM CENTER. 1 LAUTER STATION WITH CIP SPRAY BALL 1 MANHOLE WITH GLASS 1 SPRAY BALL 1 TREBERN FLAP AT THE CYLINDRICAL PART DESIGNED FOR NON PRESSURE OPERATION THE PACKAGE INCLUDES ALL VALVES, CHECK VALVES, BUTTERFLY VALVES, 2 PUMPS AND TEMPERATURE PROBES LANDING AND STAIRS MADE OF STAINLESS STEEL SQUARE ROOF BARS, COVERED WITH CORRUGATED SHEET METAL, HEIGHT ADJUSTABLE FEET WITH DOMES. THE PAN DUST WILL BE COLD DOWN WITH COLD WATER AND THE CONDENSATE WILL BE TRANSFERRED TO THE DRAIN WHIRLPOOL 20HL VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION WORTHCOOLING + WORTH AERATION VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION 1. SECTION: 20 HL WORTH IS COOLED WITH COLD WATER FROM 98°C TO 17°C IN 60 MINUTES (COLD WATER FROM CLIENT SIDE MUST BE MAX. 15°C OR LOWER) 2. SECTION: WITH ICE WATER OR GLYCOL THE WORTH IS COOLED TO 5°C CONTROL SYSTEM EACH PNEUMATIC CONTROLLED VALVE WILL HAVE A SWITCH BUTTON ON A CONTROL PANEL IN THE MIDDLE OF THE BREW HOUSE. ALSO THE TEMPERATURE CONTROL OF THE MASH KEETEL AND WORTH KETTLE WILL BE IMPLEMENTED AT THE CONTROL PANEL WITH A HARD WARE CONTROLLER. HOT WATER TANK 30 HL VERTICAL DESIGN, MATERIAL 1.4301 DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF MATERIAL 1.4301 WITH GRAIN 220 1 HOT WATER PUMP 1 CIRCULATION PUMP 1 PT 100 AN CONTROLLER 1 STEAM VALVE AND CONDENSATE VALVE 1 LEVEL INDICATION 10 X CYLINDER CONICAL TANKS 40/48 HL VERTICAL DESIGN WITH DISHED BOTTOM AND 60° CONE. CONE AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 4.050MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) AND CONE COOLING (2 ZONE), BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. SEPARATE CONNECTIONS FOR COOLING FOR CASING AND CONE : NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 2 OUTLET DN 32 INSTALLED IN A DN 125 - THREAD , PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 50, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 2 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 2 SOLENOID VALVE FOR THE COOLING DUCT 4 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. FILTRATION 20 HL/H KISELGUR- FILTER WITH HORIZONTAL SLICES AND CAPACITY OF 20HL / HOUR 3 X PRESSURE DISPENDING TANKS 40/46 HL VERTICAL DESIGN WITH DISHED BOTTOM LOWER + UPPER BOTTOM AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 3.350MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. CONNECTION FOR COOLING: NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 1OUTLET DN 32 PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN 25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32 FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 32, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 1 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 1 SOLENOID VALVE FOR THE COOLING DUCT 2 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. COOLING UNIT COOLING UNIT FOR THE OFFERT TANKS AND FOR THE WORTH COOLING. DESIGNED FOR OPERATION WITH GLYCOL COMPRESSOR OIL FREE FULLY AUTOMATIC, OIL-FREE AIR COMPRESSOR STATION WITH STAGE, MOUNTED ON A PRESSURE VESSEL, EQUIPPED WITH PRESSURE SWITCH, OUTLET VALVE, SAFETY VALVE, PRESSURE GAUGE AND MICRO FILTER. STEAM GENERATOR OIL OPERATED OIL OPERATED STEAM GENERATOR WITH A CAPACITY OF 200 KG/H INCLUDING FEED WATER TREATMENT AND FEED WATER CONTROL MOBILE BEER PUMP BEER PUMP WITH FREQUENCY CONVERTER, SINGLE MECHANICAL SEAL, ON STAINLESS STEEL FRAME (WITH CEE PLUG, MOTOR PROTECTION AND 10 M CABLE) FOR PUMPING FROM THE FERMENTATION TANKS TO THE PRESSURIZED TANK 4 PCS. BEER HOSES SET KEG-CLEANER WITH KEG-HANDFILLER CLEANER: CAPACITY: 10 – 15 KEGS / HOUR SEMI AUTOMATICALLY CLEANING PROCESS FOR ALL STANDARD KEGS KEG-HAND FILLER: COMPLETE MADE OF STAINLESS STEEL TUBES 2M LONG FOR ALL STANDARD KEGS PACKAGING WOODEN BOX AND FOILING FOR TRANSPORT IN A CONTAINER (SEA WAY), THE WOODEN BOX ALONE IS NOT ENOUGH FOR THE SEA WAY DOCUMENTATION IN ENGLISH (DEVICE DOCUMENTATION) IN ELECTRONIC FORM MOUNTING MATERIAL FOR MECHANICAL AND ELECTRICAL WORK UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING MOUNTING AND COMMISSIONING FOR MECHANIC WORK AND ELECTRIC WORK (LIFTING DEVICES- CRANE, ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET, LABOURER FOR MOUNTING SUPPORT) UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING 4 TEST BREWS (ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET) AND TRAINING OF THE OPERATOR STAFF UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING LABORATORY CIVIL WORK CO2 – SUPPLY PERMITS AND LICENSES FROM LOCAL AUTHORITIES TRANSPORT WATER TREATMENT AND COLD WATER TANK (IF REQUIRED) YEAST MANIPULATION (IF REQUIRED) Attached 3 photos from similar equipment. F1: brewhouse F2: CCT (cylindroconicalk tanks) and BBT (bright beer tanks = dispensing tanks) F3: PHE(plate heat exchanger = wort cooling, whirlpool, hot water tank) QUANTITY AVAILABLE: 1 Learn More

TT-1984 APPLE JUICE FACILITY, 90,000 LBS/HR IN, 15,500 LBS/HR OUT ITEM 001 4-EFFECT EVAPORATOR / CONCENTRATOR, MANUFACTURED BY APV, PREVIOUSLY RUNNING DEPECTINIZED FRUIT JUICE AT RATE OF 170 GPM-IN AT 3-4 BIX, 20 GPM-OUT AT 70 BRIX (90,000 LBS/HR IN, 15,500 LBS/HR OUT). STEAM CONSUMPTION OF 16,000 POUNDS PER HOUR AT 125 PSI. TOWER WATER RUNNING 1,650 GPM AT 50 DEG F. INCLUDES MATCHED CAPACITY UHT PASTEURIZING SYSTEM. EFFECTS CONSIST OF 1A/1B, 2, 3A/3B, 4A, 4B. COMPLETE SYSTEM WITH PLATE HEAT EXCHANGERS, TANKS, PUMPS, AND CONTROLS. ITEM 002 CROSSFLOW MICROFILTRATION SYSTEM, MANUFACTURED BY TECHSEP, WITH CARBOSEP CARBON MEMBRANES. HIGH SIDE AND LOW SIDE EACH RATED FOR 40 GPM FOR A TOTAL OF 80 GPM. CARBOSEP MEMBRANES FEATURE SINTERED CARBON MEMBRANE SUPPORT, METALLIC OXIDE MEMBRANE LAYER, MEASURES 1200MM/47.25 LONG X 10 MM/0.4” OD, 6 MM/0.23” ID, RATED FOR 40 BAR/580 PSI BURSTING PRESSURE, 15 BAR/217 PSI SERVICE PRESSURE, 0 TO 14 SERVICE PH, MICROFILTRATION AT 0.14 MICRONS. STAINLESS STEEL FILTRATION HOUSING MEASURES 9” DIAMETER X 4’ LONG. (3) SKIDS, EACH DRIVEN BY 60 HP GOULDS XLT-X CENTRIFUGAL PUMP. INCLUDES (2) STAINLESS STEEL CARTS OF EXTRA PARTS AND THOUSANDS OF UNUSED SPARE FILTRATION TUBE MEMBRANES STILL IN BOXES. ITEM 003 (2) 10,000 GALLON STAINLESS STEEL TANKS, MEASURES 8’ DIAMETER X 15’ HIGH, SINGLE WALL CONSTRUCTION, INCLUDES 5 HP SIDE AGITATOR MANUFACTURED BY MIXMOR, DRIVEN BY 5 HP MOTOR. FEATURES 4” CENTER BOTTOM DISCHARGE, MANWAY OPENING, AND 7.5 HP TRANSFER PUMP. ITEM 004 GRANULAR DECOLORING CARBON FILTRATION SYSTEM, LAST USED TO PROCESS FRUIT JUICE AT RATE OF 150 GPM. CONSISTS OF (2) FILTRATION COLUMNS, EACH MEASURING 3’ DIAMETER X 16’ HIGH STRAIGHT SIDE, APPROXIMATELY 850 GALLONS WITH DISH TOP AND BOTTOM; 4,000 GALLON STAINLESS STEEL SINGLE WALL “CAUSTIC” TANK WHICH MEASURES 8’ DIAMETER X 10’ HIGH STRAIGHT SIDE, 2,000 GALLON STAINLESS STEEL TANK MEASURING 6’ DIAMETER X 10’ HIGH WITH DISH BOTTOM AND 3” OUTLET; SECONDARY FILTER SKID WITH (2) COLUMNS, EACH MEASURING 8” DIAMETER X 3’ HIGH; 200 GALLON STAINLESS STEEL CIP TANK MEASURING 40” DIAMETER X 32” HIGH WITH DISH TOP; AND 10 HP FRISTAM PUMP. ITEM 005 ALFA LAVAL / DE LAVAL AUTOMATIC DESLUDGING DISC CENTRIFUGE, MODEL BRPX 417 SEV 31CCL – 60/88 – 1008 – 13, MANUFACTURING NUMBER 2982935, RATED FOR MAX SPEED OF 3980 R/M. DRIVEN BY 50 HP, INCLUDES 10 HP TRANSFER PUMP, ALLEN BRADLEY DIGITAL CONTROLS. ITEM 006 WESTFALIA AUTOMATIC DESLUDING DISC CENTRIFUGE, MODEL SB80-06-177, SERIAL # 1668 988, MANUFACTURED IN 1980, RATED FOR MAX BOWL RPM OF 4430, 1.1 KG/DM3 OF HEAVY LIQUID, 1.3 KG/DM3 OF SLOIDS. DRIVEN BY 75 HP TOSHIBA MOTOR, INCLUDES CONTROL PANEL WITH ALLEN BRADLEY TOUCHSCREEN CONTROLS. Learn More

M-6053 SPUNBOND PRODUCTION LINE, WORKING WIDTH 4040mm TO 4500mm

OFFER 001
SPUNBOND PRODUCTION LINE
WORKING WIDTH: 4040mm
WEIGHT: 130 TO 250 G/M2

OFFER 002
POLYMER CLEANING GROUP

OFFER 003
CRYSTALLIZING GROUP

OFFER 004
DRYING GROUP

OFFER 005
PNEUMATIC CONVEYING SYSTEM

OFFER 006
EXTRUDER HOPPER

OFFER 007
EXTRUDER

OFFER 008
FILTERING UNIT

OFFER 009
MELT TRANSFER LINE

OFFER 010
SPINNING BEAM

OFFER 011
SPINNING PACKS

OFFER 012
FILAMENTS QUENCHING SYSTEM

OFFER 013
FILAMENTS DRAWING AND DISTRIBUTION SYSTEM

OFFER 014
WEB FORMING CONVEYOR BELT

OFFER 015
CREEL FOR APPLICATION OF REINFORCING FILAMENTS

OFFER 016
PRE-NEEDLING MACHINE

OFFER 017
NEEDLING MACHINE

OFFER 018
THERMOSETTING UNIT

OFFER 019
OUTLET CALENDER

OFFER 020
FOULARD

OFFER 021
BINDER PREPARATION SYSTEM

OFFER 022
DRYER

OFFER 023
OUTLET CALENDER

OFFER 024
AUTOMATIC WINDER

OFFER 025
AIR COMPRESSORS (FOR FILAMENTS STRETCHING EJECTORS)

OFFER 026
DIATHERMIC OIL HEATING SYSTEM

OFFER 027
CHILLED WATER CIRCULATION AND GENERATION SYSTEM

OFFER 028
EQUIPMENT FOR CLEANING CYCLE, SPECIAL TOOLS

OFFER 029
FIBRE DUST RECOVERY SYSTEM

OFFER 030
EDGES RECOVERY SYSTEM

OFFER 031
SPINNING SECTION STEEL STRUCTURE

OFFER 032
DISTRIBUTION ELECTRIC CABINETS

OFFER 033
PROCESS ELECTRIC SYSTEM OF EXISTING MACHINES ACCORDING TO THE ACTUAL LAYOUT

OFFER 034
CABLES AND CABLING MATERIALS

QUANTITY: 1 LINE

Learn More