Search results for: 'Winder machine se'

T-9752 KARL MAYER CARBON MACHINES BIAXIAL AND MULTIAXIAL PROPERTIES: SINCE ALL FIBERS POINT IN ONE DIRECTION, THE SCRIM CAN BE IDEALLY DRAPED GOOD SOAKABILITY WITH LITTLE RESIN CONSUMPTION CAN BE DRAPED VERY WELL AROUND CURVES AND EDGES EASY TO CUT ELECTRICALLY CONDUCTIVE, INFUSIBLE HIGH STRENGTH AND RIGIDITY DUE TO GRAPHITE-LIKE FIBER STRUCTURE BIOCOMPATIBLE TRANSPARENT TO X-RAYS LOW SPECIFIC WEIGHT IDEAL FOR SURFACE USE (LITTLE FIBER IMPRINTS) IDEAL FOR PROCESSING WITH EPOXY RESIN! TEXTILE SEMI-FINISHED PRODUCTS MADE OF PRE-SPREAD AND PLANE-PARALLEL LAID FIBERS FORM THE GROUP OF UNIDIRECTIONAL FABRICS. THE FIBERS ARE USUALLY LAID AT 0°, MORE RARELY AT 90°. BY LAYING THE UD FABRICS ALONG THE LINES OF FORCE ACTING IN THE COMPONENT, THE LIGHTWEIGHT POTENTIAL OF THE CARBON FIBER IS OPTIMALLY EXPLOITED. UD FABRICS CONSIST OF ONE OR MORE SUPERIMPOSED FIBER LAYERS FIXED WITH AN EPOXY-COMPATIBLE BINDER THREAD. THE SPECIAL SPREADING TECHNIQUE PRODUCES FABRICS WITH HIGH FIBER PARALLELISM, WITHOUT KNOTS AND FIBER TWIST. SPREAD FIBERS ABSORB THE RESIN BETTER, RESULTING IN HIGHEST LAMINATE STRENGTHS. QUANTITY: 3 LINES Learn More

REFERENCE NUMBER: M-1758 (6602BHBBE5U) GEOTEXTILE CALENDER MACHINE -5700mm- YEAR 2004 MAKE: BOMBI MECCANICA ITALY 5.7 M WIDE GEOTEXTILE CALENDER MACHINE YEAR: 2004 IS IN PERFECT CONDITION FEW HOUR PRODUCTION IT IS CONNECTED AND CAN BE SHOWN TO CUSTOMERS VOLTAGE: 440V / 60 HZ / 3 PHASES UNWINDER ACCUMULATORS WITH ROLLS, 50M OF CONTENT 2 ROLLS CALENDER 5.7 WIDE 200,000 KCAL/HR GAS OIL HEATER UPPER HOOD FOR THE SMOKE COLLECT METAL DETECTOR INSTALLED ON TOP OF CALENDER ADJUSTING 2 ROLLS TEMPERATURE INDEP. ACCUMULATORS WITH ROLLS, 50 M LONG CROSS CUTTER W/6 LONG SLITTERS, AND EXIT BELT WINDER OPTION ROLL DISCHARGER 2.3 M WINDER, SPEED UP TO 30 M/MIN, READY TO BE SYNCHRONIZED 2.3 M WIDE, EDGE TRIMMERS WITH 2 DISC BLADES FELT WIDTH: 5.5 METER WEB THICKNESS AT ENTRY: AROUND 1 TO 2 mm WEB PREPARATION AT THE INLET: CROSS LAPPING AND NEEDLING PRODUCTION LINE SPEED: UP TO 25 M/MIN TYPE OF TREATMENT: HEAT SETTING, SMOOTHING OF THE SURFACES AND CALIBRATION, CUTTING AND ROLLING UP FELT WEIGHT: 90 TO 300 GSM FIBERS: POLY COTTON BLEND, POLYESTER, ACRYLIC, POLYPROP THERMOSETTING TEMEPRATURE: UP TO 225°C QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

TT-4545 BOBST NOVA SX 550 LAMINATOR 800 / 350, YEAR 2022 SOLVENTLESS-LAMINATOR YEAR OF CONSTRUCTION: 2022 FOR NARROW WEB FLEXIBLE PACKAGING Learn More

TT-6187 HIGH TENCITY PP FDY MULTIFILAMENT YARN PLANT, UP TO 6.5 G.P.D, YEAR 2015 1. HIGH TENCITY PP FDY MULTIFILAMENT YARN PLANT 2. UP TO 6.5 G.P.D 3. BRAND: HSN KOOK MACHINERY 4. YEAR OF MANUF.: 2015 5. RANGE OF PRODUCTION; 500D/2~3, 1200D/3 6. 1 COPE X 8 WINDER SYSTEM 7. TENACITY RANGE: MAX 6.5 ~ 7.0 G.P.D 8. PRODUCTION CAPACITY: 1,400 ~ 1,500KG/DAY 9. (BASED ON 900 DENIER) Learn More

TT-5907 ASSEMBLING WINDER RITE/ITALY, TYPE AER-L, 40 SPINDLES, YEAR 1996 ASSEMBLING WINDER RITE/ITALY, TYPE AER-L YEAR 1996 QUANTITY: 1 Learn More

TT-2155 RIETER COMPLETE SPINNING PLANT WITH 16,128 SPINDLES, YEAR 1991 TO 1995 RIETER COMPLETE SPINNING PLANT 16,128 SPINDLES YEAR 1991 TO 1995 QUANTITY: 1 PLANT Learn More

TT-1585 ACRYLIC SPINNING PLANT, YEAR 2001 TO 2007 DISMANTLED, READY FOR SHIPPING REQUIRES 20 TO 22 40 FOOT HIGH CUBE CONTAINERS TO SHIP Learn More

REFERENCE NUMBER: M-3350

RIETER K45 RING SPINNING FRAMES LINKED WITH MURATA 21C WINDERS- YEAR 2008 TO 2009

 

RIETER COMPACT RING SPINNING FRAMES MOD. K45

YEAR: 2008/09

NUMBER OF SPINDLES: 1632

SPINDLE GAUGE: 70mm

RING TUBE LENGTH: 200mm

SPINDLE WHARVE DIAMETER: 18mm

DRAFTING SYSTEM: RIETER

RING DIAMETER: 40mm

OHTC: CHINESE

CREEL: NR. 6 ROWS

MAIN MOTOR: 80KW

SUCTION MOTOR: 15KW

SUCTION: INDIVIDUAL

WASTE COLLECTION: MANUAL

DOFFER: AUTO DOFFER LINKED

BOTTOM ROLLER: 27mm

QUANTITY: 6

 

LINKED TO:

MURATA CONE WINDERS MOD. 21C

YEAR : 2008

NUMBER OF DRUMS: 34

YARN CLEARER: USTER QUANTUM 2 WITH FOREIGN FIBER SENSOR

MEASURING HEAD: MK C15 F23

MACHINE HAND: 3 X LH, 3 X RH

SPLICER: G 2Z

WAXING: AVAILABLE

SUCTION: INDIVIDUAL

OHTC: AVAILABLE

PACKAGE CONVEYER BELT: AVAILABLE

DOFFER: AUTO

QUANTITY: 6

Learn More

REFERENCE NUMBER: M-5492 (330BPBRXX2) L SCHWEITER KEK-PN CONE-TO-CONE PRECISION WINDERS FOR POLYAMIDE & POLYESTER YARNS- 40 positions for cones and for dye bobbins PRECISION WINDERS SCHWEITER, TYPE KEK-PN FROM CONE TO CONE WINDING AND REWINDING MACHINES FOR POLYAMID AND POLYESTER FILAMENT YARNS ONE SIDED MACHINE WITH 40 WINDING HEADS TRAVERSE 8” = 200mm CONICITY 3°30 MACHINES SUITABLE FOR 140 TO 210 DENIER TEXTURED DYED OR UNDYED POLYAMIDE AND POLYESTER YARN – ALSO SUITABLE FOR WINDING SOFT DYEING PACKAGES ADJUSTABLE CERAMIC TENSION DEVICES OILING SYSTEM EACH SET OF 2 MACHINES FITS IN 1 x 40’ CONTAINER QUANTITY AVAILABLE: 12 Learn More