J-3004 FIBRILLATED RAFFIA TAPE EXTRUSION LINE – NEW, 120mm

REFERENCE NUMBER: J-3004 FIBRILLATED RAFFIA TAPE EXTRUSION LINE – NEW, 120mm PP FIBRILLATED YARN EXTRUDER LINE MODEL: NOVASTAR-120 EXTRUSION LINE FOR PRODUCTION OF PP FIBRILLATED YARN RAW MATERIAL: PP GRANULE FINISHED PRODUCTS: NON-TWISTED TAPE YARN, FIBRILLATED YARN FOR TWINE RANGE OF PRODUCT: 10,000 TO 30,000 DENIER 10000 DENIER APPROXIMATELY 17 TO 19 YARN 16000 DENIER APPROXIMATELY 11 TO 12 YARN 22000 DENIER APPROXIMATELY 8 TO 9 YARN 28000 DENIER APPROXIMATELY 6 TO 7 YARN 32000 DENIER APPROXIMATELY 5 TO 6 YARN EXTRUSION THROUGHPUT: 300 KG PER HOUR EXTRUSION CAPACITY: 180 TO 250 KG PER HOUR (PRODUCT CAPACITY DEPEND ON FILAMENT SIZE) EXTRUDER SCREW DIAMETER: Ø 120mm T-DIE WIDTH: 1300mm TAKE-OFF ROLLER WIDTH: 1200mm TAKE-OFF LINE SPEED: 160 METERS PER MINUTE (MAXIMUM) OPERATION SIDE: RIGHT TO LEFT, OR LEFT TO RIGHT EXTRUSION ITEM 001 EXTRUDER SCREW DIAMETER: Ø120mm SCREW L/D: 28:1 SCREW BARREL MATERIAL: SACM-645 STEEL NITRIDE HARDEN, NORMALIZATION HRC 55-60° GEAR BOX: SL-150 (1/10) HELIX GEAR GEAR BOX LUBRICANT SYSTEM: WITH OIL PUMP LUBRICATION DRIVING MOTOR: 150 HP AC MOTOR WITH ABB INVERTER CONTROL HEATING ZONE: 6 ZONES (CYLINDER & HEAD) HEATING SYSTEM: BY BAND HEATER HEATING CAPACITY: 42 KW (APPROXIMATELY) COOLING FOR HOPPER JACKET: WATER COOLING SYSTEM COOLING OF CYLINDER: AIR COOLING SYSTEM BY 1/4 HP BLOWER X 6 SET SCREW EXTRACTOR TOOL: 1 SET (ATTACHED WITH GEARBOX) QUANTITY: 1 BASED RACK FOR EXTRUDER DEVICE TYPE: STATION TYPE BASED RACK FOR SUPPORTING THE EXTRUDER AND GEARBOX QUANTITY: 1 T-DIE SET T-DIE WIDTH: 1300mm X 1SET DIE-LIP WIDT: 1200mm EFFECTIVE WIDTH: 1100 TO 1050mm T-DIE GAP: 1.2 TO 1.8mm DIE LIP SET: FLAT OR GROOVED HEATING ZONE: 5 ZONES HEATING SYSTEM: CARTRIDGE HEATER (ROD HEATER) HEATING CAPACITY: 28 KW QUANTITY: 1 QUENCHING ITEM 002 QUENCHING WATER BATH DEVICE TYPE: WATER CIRCULATION SYSTEM, MOVABLE AND HEIGHT ADJUSTABLE INNER BATH: STAINLESS STEEL #304 TANK SIZE: 1400mm L X 1200mm W X 550mm D WATER DISTRIBUTION SYSTEM: 1 SET QUANTITY: 1 IYEM 003 TAEK-UP NIP ROLLER TAKE-UP NIP ROLLERS: Ø 215mm X 1300mm L - 1 SET (BY PNEUMATIC CYLINDER) TAKE-UP MOTOR: 3 HP (0.75 KW) AC MOTOR WITH ABB INVERTER CONTROL WATER STRIPPER: 3 HP SUCTION BLOWER WITH SUCTION PIPE AND WATER STOPPED ROLLER QUANTITY: 1 SLITTING ITEM 004 SLITTING UNIT SLITTING DEVICE: ADJUSTABLE CUTTING BLADES X 1 UNIT POSITION ADJUSTABLE: UP / DOWN, AND L TO R ADJUSTABLE CUTTING BLADE: SLITTING KNIFE X 16 PIECESS PRODUCTION CALCULATION (BASED ON RUNNING 10000 TO 32000 DENIER RANGE) 10000 DENIER APPROXIMATELY 17 TO 19 YARN (SLITTING WIDTH 55mm) 16000 DENIER APPROXIMATELY 11 TO 12 YARN (SLITTING WIDTH 90mm) 22000 DENIER APPROXIMATELY 8 TO 9 YARN (SLITTING WIDTH 120mm) 28000 DENIER APPROXIMATELY 6 TO 7 YARN (SLITTING WIDTH 155mm) 32000 DENIER APPROXIMATELY 5 TO 6 YARN (SLITTING WIDTH 180mm) QUANTITY: 1 GODET ROLLER UNIT NO.1: (TAKE-OFF UNIT A) TAKE-OFF UNIT TYPE: OIL IMMERSED GEAR DRIVE - 5 ROLLERS TAKE-OFF ROLLER: Ø 295mm X 1200mm L ROLLER SURFACE: CHROMED PLATED DRIVING MOTOR: 10 HP AC MOTO WITH ABB INVERTER CONTROL TAKE-OFF SPEED: 10 TO 50 METERS PER MINUTE RUBBER PRESS ROLLER: Ø 150mm X 1150mm L - PNEUMATIC OPERATED X 1 SET ATTACHED WITH: CONTROL PANEL WITH ON/OFF SWITCH, SPEED METER, AND EMG STOP BUTTON QUANTITY: 1 EDGE TRIMS RECLAIM SYSTEM TRIMS CRUSHER: 1 HP CONVEYOR BLOWER: 2HP CONVEYOR BLOWER CHIP SCREW FEEDER: 1/4HP WITH SILO HOPPER QUANTITY: 1 STRETCHING ITEM 005 STRETCHING HOT AIR OVEN DEVICE TYPE: DOUBLE DECK HEATING CIRCULATION HOT AIR OVEN OVEN SIZE: 4500mmL X 1200mm WIDTH HOT AIR CIRCULATION SYSTEM: 2 HP CIRCULATION FAN X 2 SET WITH INVERTER CONTROLLER HEATING METHOD: ELECTRIC HEATER PIPE HEATER CAPACITY: 36 KW AUTO. THERMOS-CONTROLLER: 2 SET ATTACHED WITH: CONTROL PANEL WITH A-METER, ON/OFF SWITCH OVEN OPEN/CLOSE: 2 STAGES BY PNEUMATIC CYLINDERS QUANTITY: 1 ITEM 006 GODET ROLLER UNIT NO.2: (TAKE-OFF UNIT B) TAKE-OFF UNIT TYPE: OIL IMMERSED GEAR DRIVE - 7 ROLLERS TAKE-OFF ROLLER: Ø 295mm X 1200mm L - 5 PIECES WATER COOLED ROLLER: Ø 295mm X 1200mm L - 2 PIECES (WITH ROTARY JOINT) ROLLER SURFACE: CHROMED PLATED DRIVING MOTOR: 20 HP AC MOTOR WITH ABB INVERTER CONTROL TAKE-OFF SPEED: 0 TO 160 METERS PER MINUTE RUBBER PRESS ROLLER: Ø 150mm X 1150mm L - PNEUMATIC OPERATED X 1 SET (ROLLER B7) ATTACHED WITH: CONTROL PANEL WITH ON/OFF SWITCH, SPEED METER, AND EMG STOP BUTTON QUANTITY: 1 FIBRILLATING ITEM 007 FIBRILLATOR UNIT FIBRILLATING ROLLER: Ø138mm X 1200mm L X 1 SET (INTEGRATED IN GODET UNIT NO.2) FIBRILLATING WIDTH: 1100mm NEEDLE STRIP DENSITY: 1 SET - 8 NEEDLE/CM X 36 SLOTS (2 STAGGER OFF-SET) - BY BURCKHARDT FIBRILLATER DRIVING MOTOR: 10 HP (7.5KW) AC MOTOR WITH ABB INVERTER CONTROL LINE SPEED: 60 TO 240 METERS PER MINUTE ATTACHED WITH: CONTROL PANEL WITH ON/OFF SWITCH, SPEED METER, AND EMG STOP BUTTON. QUANTITY: 1 ITEM 008 GODET ROLLER UNIT NO.3: (TAKE-OFF UNIT C) TAKE-OFF UNIT TYPE: OIL IMMERSED GEAR DRIVE - 5 ROLLERS TAKE-OFF ROLLER: Ø 295mm X 1200mm L - 5 PIECES ROLLER SURFACE: CHROMED PLATED DRIVING MOTOR: 10 HP AC MOTO WITH ABB INVERTER CONTROL TAKE-OFF SPEED: 0 TO 160 METERS PER MINUTE RUBBER PRESS ROLLER: Ø 150mm X 1150mm L - PNEUMATIC OPERATED X 1 SET (ROLLER B7) ATTACHED WITH: CONTROL PANEL WITH ON/OFF SWITCH, SPEED METER, AND EMG STOP BUTTON QUANTITY: 1 CONTROL CABINET & CONTROL SYSTEM ITEM 009 CONTROL CABINET AIR VENTILATION COOLING DESIGN - WITH AIR VENTILATION FOR OPTIMUM COMPONENT PERFORMANCE PROCESS CONTROL SYSTEM: 1 UNIT MAIN SUPPLY: WITH MAIN SWITCH EMERGENCY SYSTEM: BY EMERGENCY SWITCH INVERTER: AC-DRIVE SYSTEM BY ABB INVERTER CONTROL AUTO TEMP. CONTROLLER: ON/OFF SWITCH, THERMO CONTROLLER X 12 SET MAIN DRIVE: POWER SWITCH, A-METER, RPM & POTENTIOMETER X 1 SET MAIN DRIVE CONTROL: 150 HP (112.5 KW) INVERTER CONTROLLED X 1 SET UNIT DRIVE CONTROL: 10 HP (7.5 KW) INVERTER CONTROLLER (DRAW-STAND NO.1) X 1 SET 20 HP (15 KW) INVERTER CONTROLLER (DRAW-STAND NO.2) X 1 SET 10 HP (7.5 KW) INVERTER CONTROLLER (FIBRILLATED UNIT) X 1 SET 10 HP (7.5 KW) INVERTER CONTROLLER (DRAW-STAND NO.3) X 1 SET DRAW STAND CONTROL: ON/OFF SWITCH, A-METER, POTENTIOMETER, METERS PER MINUTE GAUGE X 3 SET SYNCHRONIZED CONTROL: MANUAL / AUTOMATIC SWITCH, SPEED UP & DOWN SWITCH X 1 SET QUANTITY: 1 ACCESSORIES & SPARE PARTS (SUPPLY WITH COMPLETE LINE ORDER) TAKE-OFF UNIT GEAR REDUCER COOLING DEVICE X 2 SET TAKE-OFF UNIT EMERGENCY STOP FOOT-PAD & TEMPERATURE GAUGE X 3 SET TOOLBOX & ASSORTED TOOLS X 1 SET STANDARD SPARE PARTS X 1 SET OPTIONAL EQUIPMENT ITEM 010 CENTRAL PROCESS MONITORING & CONTROL SYSTEM UPGRADE CONTROL & MONITORING COMPLETE EXTRUSION LINE & TAKE-OFF UNIT SYSTEM TYPE BY FATEK PLC WITH 12” ADT HMI TOUCH SCREEN PLC & PROGRAM CONFIGURATION FOR JC-MNP SERIES: TEMPERATURE CONTROL MODULE + ANALOG MODULE + DIGITAL INPUT MODULE FEATURES: EXTRUDER TEMPERATURE DIGITAL CONTROL (SV/PV/AMP DISPLAY) EXTRUDER CONTROL (RPM / AMP / % DISPLAY) PRESSURE MONITORING SYSTEM (BAR DISPLAY) STRETCHING BATH & OVEN TEMPERATURE DIGITAL CONTROL (SV/PV/AMP DISPLAY) LINE SPEED CONTROL (METERS PER MINUTE / AMP / % DISPLAY) SYNCHRONIZE CONTROL (A-B-C RATIO) RAMP UP/DOWN CONTROL RECIPE RECORD (15 SET) POWER CONSUMPTION RECORD TREND GRAPH & ALARM MESSAGE ITEM 011 AIR CONDITIONING FOR CONTROL CABINET AIR CONDITION: 1 SET & ATTACHED WITH MAIN CONTROL CABINET. AIR COOLING VENTILATION CONTROL PANEL DESIGN - WITH TOP & BOTTOM AIR VENTILATION INSIDE ELECTRICAL CABINET FOR OPTIMUM COMPONENT PERFORMANCE. QUANTITY: 1 ITEM 012 MELT PRESSURE & TEMPERATURE MONITORING QUANTITY: 1 ITEM 013 HOPPER DRYER SYSTEM LOADER: 150 LITER DRYING CAPACITY: 6 KW BLOWER: 0.25 KW DRYER METHOD: DOWN-BLOWING AND CYCLONIC EXHAUST PRINCIPLE CONTROL: DIGITAL TEMPERATURE SETTING, AUTO START-UP CLOCK, FAULT DIAGNOSIS. QUANTITY: 1 ITEM 014 DOTECO GRAVIMETRIC DOSING SYSTEM & CONVEYING SYSTEM DOTECO GRAVIMETRIC GRADO-ADROIT (MADE IN ITALY) COMPARTMENT: 4 REMOVABLE HOPPER BINS (UPGRADABLE TO 6) MATERIAL DOSE RANGE: 0 TO 100% (FOR MAIN MATERIAL)\ SUB-MATERIAL DOSE RANGE: 50 TO 100% (FOR SUB MAIN MATERIAL)\ ADDITIVE DOSE RANGE: 1 TO 5% (FOR 2 INGREDIENTS/ADDITIVE) DOTECO VACUUM UNIT: DBLO CENTRAL VACUUM PUMP BLOWER: 3KW, 400V/3/60Hz VACUUM RECEIVER: 4 PIECES (VRS-S10) ITEM 015 CONTINUOUS BELT TYPE SCREEN CHANGER UPGRADE NON-STOP CONTINUOUS SCREEN BELT TYPE CHANGER SCREEN CHANGE BY PRESSURE CONTROL HEATING AND STOP BY WATER COOLING SCREEN BELT 127mm: 1 ROLL SCREEN PRESSURE GAUGE: GEFRAN M31+40B X 1 SET (FOR SCREEN CHANGE CONTROL) TEMPERATURE CONTROL: 3 ZONES (SCREEN IN, MELT FLOW, SCREEN OUT) ITEM 016 NORDSON MELT FILTER FOR CONTINUOUS OPERATION BKG® NORCON™ K-SWE101 - MELT FILTER FOR CONTINUOUS PRODUCTION WITH TWO SCREEN BEARING PISTONS - DURING THE PRODUCTION THE MELT IS SPLIT INTO TWO FLOW CHANNEL INSIDE THE HOUSING AND LED TO ONE SCREEN CAVITY EACH BEFORE BEING BROUGHT TOGETHER AGAIN AFTER FILTRATION - 50% OF FILTRATION AREA ARE AVAILABLE DURING SCREEN CHANGE - 4 THERMOCOUPLE BORINGS IN THE HOUSING (LOCATE ON THE TOP & BOTTOM OF THE HOUSING) TECHNICAL DATA - SCREEN DIAMETER: 2 X 96.3mm - FILTRATION AREA: 2720mm = 1440mm - INSTALLATION LENGTH: 220mm HEATING - TOTAL HEATING CAPACITY: APPROXIMATELY 9.6KW - HEATING ZONE: 2 - HOUSING: 2 HEATING ZONES CAPACITY OF EACH ZONE APPROXIMATELY 4.8KW (3 HEATING CARTRIDGE EACH APPROXIMATELY 1.6 KW), IP54 - THE HEATING ELEMENTS WLL BE WIRED READY FOR CONNECTION IN TERMINAL BOXES HYDRAULIC POWER RUNIT TYPE LR2.8 - RADIAL-PISTON PUMP WITH STEEL TANK INCL. LEVEL INDICATOR AND REVERSE-FLOW FILTER - MOTOR: 1.5 KW, 400V, 50Hz IP54 - PUMP FLOW RATE: 2.8 L/MIN - OPERATION PRESSURE: MAXIMUM. 300 BAR - CONTENTS OF OIL RESERVOIR: 6L DIGITAL POSITION DISPLAY - 2 DIGITAL DISPLAYS, 4 DIGIT - 2 DISPLACEMENT TRANSDUCER TYPE BALLUFF FOR INSTALLATION INTO THE HYDRAULIC CYLINDERS - DIGITAL DISPLAYS INCL. TRANSFORMER INSTALLED INTO A SMALL CONTROL CABINET WITH OVERALL VOLTAGE INLET WIRING & FITTING - TEMP CONTROLLER & PRESSURE CONTROLLER WIRING & FITTING SAFETY GUARD - MOVEABLE GUARD TO THE SIDE OF THE MELT FILTER (WITH LIMIT SWITCH). - MADE OF STAINLESS STEEL DIN 1.4301 QUANTITY: 1 ITEM 017 NORDSON MELT FILTER HANDLING & ADAPTOR FITTING QUANTITY: 1 ITEM 018 QUENCHING BATH MOTORIZED ELEVATION SYSTEM QUANTITY: 1 ITEM 019 WATER CHILLER 20 RT REFRIGERATING CAPACITY: 48,000 / 60,0000 / KCAL/H (50/60Hz) COMPRESSOR POWER: 20 HP (7.5KW X 2) WATER PUMP: 2 HP (180 L/MIN) ICE WATER TEMP.: 5 TO 25°C TEMP CONTROL: DIGITAL CONTROLLER CIRCULATION PUMP & CONNECTION QUANTITY: 1 ITEM 020 THERMO WATER HEAT EXCHANGER SYSTEM DEVICE TYPE: QUADRATIC WATER SUPPLY TANK FOR QUENCHING BATH WITH CONTROLLER INLET WATER FILTER: 1 SET HEAT EXCHANGE TYPE: PLATE TYPE TEMPERATURE CONTROLLER: 1 SET PROPORTIONAL VALVE DEVICE: 1 SET (3 WAY PROPORTIONAL VALVE) WATER PUMP: 2 SET WATER FILTER SYSTEM: 1 SET QUANTITY: 1 ITEM 021 JUMBO PACK CROSS WINDER (20KG) 24 SPINDLE / 6 UNIT TYPE: 20KG JUMBO PACK CROSS WINDER NUMBER OF SPINDLES: 24 PIECES NUMBER OF SPINDLE PER UNIT: 4 SPINDLE PER RUNIT SPINDLE ARRANGEMENT: (2 ROW X 2 COLUMN) X 6 UNIT BLOCK DENIER RANGE: 9,000 TO 32,000 DENIER WINDING MOTOR: 20 KG/CM TORQUE MOTOR WINDING TENSION: BY TORQUE MOTOR TRAVERSE DEVICE: BY TRAVERSE GROOVE SCROLL CAM TRAVERSE LENGTH: 305mmL WINDING SPEED: 200 METERS PER MINUTE (MAXIMUM) BOBBIN CORE: Ø 72mm LD X 350mm L PACKAGE SIZE: 300 mm L X Ø 350mm MAXIMUM. 20 KG ITEM 022 HEAVY DUTY CROSS WINDER (100KG) 8 SPINDLE / 8 UNIT TYPE: 100KG HEAVY DUTY CROSS WINDER NUMBER OF SPINDLES: 8PIECES NUMBER OF SPINDLE PER UNIT: 1 SPINDLE PER UNIT SPINDLE ARRANGEMENT: INDEPENDENT TYPE X 8 UNIT BLOCK DENIER RANGE: 9000 TO 120,000 DENIER WINDING MOTOR: 1.1 KW AC MOTOR WITH INVDERTER DRIVE WINDING TENSION: DANER REGULATED TENSION 500 TO 10,00CN TRAVERSE DEVICE: BY TRAVERSE GROOVE SCROLL CAM L TRAVERSE LENGTH: 305mmL WINDING SPEED: 200 METERS PER MINUTE (MAXIMUM) BOBBIN CORE: Ø 96mmID X 550mmL PACKAGE SIZE: 500mmL X Ø 7001mm PACKAGE WEIGHT: MAXIMUM. 100 KG ITEM 023 TAKE-OFF ROLLER GODET SAFETY COVER QUANTITY: 3 ITEM 024 YARN DROP SENSOR PHOTOVOLTAIC SENSOR: 1 PIECES BUZZER: 1 PIECES RELAY (WITH BRACKET): 1 PIECES QUANTITY: 1 ITEM 025 FINISHING OIL TREATMENT UNIT QUANTITY: 1 ITEM 026 WASTE YARN COLLECTOR (#810) INDEPENDENT TYPE SUCTION BLOWER: 7.5 HP WASTE YARN COLLECTOR: 1000mm X 1000mm X 1200mm SUCTION FUNNELS: ATTACHED ON TAKE-OFF UNIT C QUANTITY: 1 ITEM 027 CENTRAL WASTE YARN SUCTION SYSTEM SUCTION BLOWER: 25 HP VACUUM BLOWER WASTE YARN COLLECTOR: 1900mm X 1800mm X 1900mm SUCTION FUNNELS: 3 SET - ATTACHED ON TAKE-OFF UNIT A + B + C SUCTION PIPE: NOT IN THE SCOPE OF QUOTE, TO BE QUOTE PER GIVEN SPECS QUANTITY: 1 ITEM 028 ANTI-STATIC BAR 1 UNIT QUANTITY: 1 ITEM 029 TEST RUN RAW MATERIAL & SPOOL HDPE - RAW MATERIAL: 2000 TO 2500 KG (EST. 2 DAY TEST RUN PERIOD) WINDING BOBBIN CORE: 48 TO 80 PIECES ITEM 030 SERVICE & COMMISSIONING PLASCO FILED SERVICE TECHNICIAN (S) WILL SUPERVISE THE STARTUP AND THE COMMISSIONING AND PROVIDE BASIC TRAIN FOR TOTAL PERIOD OF 4 WORKING DAY. DOMESTIC TRANSPORTATION, LOCAL TRAVEL, BOARD, AND LODGING WILL BE AT CUSTOMER’S CHARGE. IF FOR ANY REASON TECHNICIAN (S) REQUIRES TO EXTEND THE VISIT, PLASCO WILL CHARGE US$300/DAY PER TECHNICIAN FOR EACH ADDITIONAL DAY. DUE TO PANDEMIC SITUATION AND REGULATION OVER COVID-19 OUTBREAK, SERVICE & COMMISSIONING CAN NOT BE CARRY OUT UNTIL FURTHER NOTICE ON SAFE TRAVEL AND RELEASE OF INTERNATIONAL BORDER CONTROL. TECHNICAL DATA PLANT DESTINATION: USA ENVIRONMENT: ALTITUDE ABOVE SEA LEVEL < 500 M.A.S.L. AMBIENT TEMPERATURE RANGE 30°C ± 10 °C (*OPTIONAL *CONTROL PANEL AIR CONDITION SUGGESTED FOR OVER 30°C) AIR HUMIDITY 10 TO 80%, NO CONDENSATION ERECTION OF THE EXTRUSION LINE IN ROOMS AS DRY AND DUST-FREE AS POSSIBLE STANDARDS SYSTEM OF MEASURE: METRIC SOFTWARE LANGUAGE: ENGLISH (PER OPTIONAL ITEM #1) LABELS: ENGLISH DOCUMENTATION USER MANUAL: ENGLISH 1 PAPER COPY (INSTRUCTIONS) TECHNICAL DRAWING: ENGLISH 1 PAPER COPY (LAYOUT & ASSEMBLY DRAWINGS) WIRING DIAGRAMS: ENGLISH 1 PAPER COPY (ELECTRICAL CIRCUIT DIAGRAM) COLOR MAIN COMPONENTS & CABINET: RAL 7035 (GREY) STEEL FRAMES: RAL 5002 (BLUE) UTILITIES POWER SUPPLY: 380V 480V (+10% -5%) 50Hz 60Hz (± 2%) 3 PHASE (4 CABLE NORM R.S.T.G.) MAIN CABINET POSITION WITHIN 3 METERS FROM EXTRUDER OPERATOR’S CONTROL PANEL (HMI) WITHIN 2 METERS FROM EXTRUDER FLOOR TYPE CABLE WATER SUPPLY: PRESSURE 4 BAR (± 1 BAR) SALT FREE WATER MAXIMUM. 12 DEGREES DH: TEMPERATURE 18°C TO 25°C COMPRESSED AIR SUPPLY: DRY, MIN Y 6 TO 8 BAR AT FEEDING POINT DEW POINT - 25 DEGREE C DUST OIL WATER CONTENT - NONE QUANTITY: 1