Search results for: 'elect'

TT-1890 NUOVO PIGNONE FAST R TYPE LOOMS, WIDTH 2200mm, YEAR 1994 TO 1995, DOBBY NUOVO PIGNONE FAST R TYPE WITH ELECTRONIC TAKE UP YEAR 1994 TO 1995 WIDTH 2200mm STAUBLI ELECTRONIC DOBBY 20 / 20 INSTALLED QUANTITY: 10 SETS Learn More

TT-7680 SIEMENS SST 400 CONDENSING STEAM TURBINE, YEAR 2011, 50/60Hz, 30 MW SIEMENS SST 400 YEAR 2011 TYPE: SST 400 CONDENSING STEAM TURBINE WITH FOUR BLEEDS AND ONE EXTRACTION TURBOSE OUTPUT: (AT GENERATOR TERMINALS) NORMAL 30 MW MAXIMAL 31.88 MW MINIMAL 4.5 MW QUANTITY: 4 Learn More

TT-2791 SIEMENS SST-400 STEAM TURBINE, 30MW, 10500V, 50Hz QUANTITY: 1 Learn More

P-5039 COMPLETE PLANT WITH DYEING – FINISHING – WEAVING - SEWING

PLAIN DYEING AND FINISHING EQUIPMENT:
7 DYEING MACHINES
9 AUTOMATIC DOSING SYSTEM
10 DYEING MACHINE – JIGGER
11 DYEING MACHINE – JIGGER
15 INSPECTION MACHINE
16 MACHINES FOR BONDING PIECES (GOODS)
18 WINDING MACHINE
19 INSPECTION MACHINE
20 MEASURING WINDING MACHINE
21 HEAT EXCHANGER
DOUBLING MACHINE

YARN DYEING AND DRYING:
1 DYEING APPARATUS
2 DYEING APPARATUS
3 DYEING APPARATUS
4 PRESSURE DRYING APPARATUS – TANDEM
5 DYEING APPARATUS
6 DYEING APPARATUS
7 THE LOADING AND UNLOADING DEVICE
8 BRIDGE CRANE
9 PROCESS WATER REGENERATION + TANK

SEWING:
8 SEWING MACHINE FOR WASHING GLOVES
9 CONTROL TABLES
10 PACKING MACHINES

DOUBLING, TWISTING, WARPING AND WEAVING:
3 WINDING MACHINE
4 MOBILE REGALS FOR YARN STORAGE

WARPING AND WEAVING:
1 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
2 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
3 WARPING MACHINE
4 SIZING MACHINE
5 SIZING MACHINE
13 COMPRESSOR FOR COMPRESSED AIR
14 KNOTTING MACHINES
15 ELEVATOR FOR BEAMS
16 ELEVATOR FOR BEAMS
17 PUNCH MACHINE
18 ELEVATOR FOR BEAMS
19 MOBILE REGALS FOR BEAM STORAGE

WEAVING SAURER 1;2;3;4:
STAUBLI JACQUARD – WITH 560 HOOKS X 4 – 10 PIECES
STAUBLI JACQUARD – WITH 768 HOOKS X 4 – 4 PIECES
STAUBLI JACQUARD – WITH 1120 HOOKS X 2 - 2 PIECES
STAUBLI JACQUARD – WITH 912 HOOKS X 2 – 1 PIECE

WEAVING SILK:
WEAVING MACHINE – LOOMS SM 93
CONTROL TABLE

READY MADE DEPARTMENT FOR TERRY BATHROBES:
CUTTING TABLE – BULLMERWERK – 1 PIECE
SEWING MACHINE – JUKI – 2 PIECES
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE –LEVIS – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – JUKI – 2 PIECE
SEWING MACHINE – MAUSER SPECIAL – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – 1 PIECE
SEWING MACHINE – NECCHI – 4 PIECES
SEWING MACHINE – PFAFF – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE

LABOR MACHINES:
APPARATUS FOR MEASURING ZTWIST, TURN/ROLL – TORSIOMETER
APPARATUS FOR MEASURING THE FRICTION COEFFICIENT
LIGHTING CHAMBER
AA WINDING APPARATUS FOR THE DYEING TUBE THE SAMPLING DEVICE
WINDING APPARATUS FOR COLOR STANDARDS
YARN DYEING APPARATUS PRETEMA MULTICOLOR
DYNAMOMETER FOR SPINNING
SPEKTROFOTOMETER DATACOLOR INTERNATIONAL – LABOR MACHINE
APPARATUS FOR THE VISUAL APPEARANCE OF THE YARN – LABOR MACHINE

ADDITIONAL DESCRIPTION

PLAIN DYEING AND FINISHING EQUIPMENT:
7. DYEING MACHINE
SCHIRM
MODEL: SURFER
YEAR: 1994
CAPACITY : 380 – 400 KG
TECHNICAL INFORMATION:
WOVEN TERRY DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
SEDOMAT PC 3100
QUANTITY: 1 (NO 94)

9. AUTOMATIC DOSING SYSTEM
LAWER
YEAR: 2002
CHEMICAL DISPENSING SYSTEM
20 PVC TANKS (CAPACITY 200 L TO 1200 L)
2 EXTERNAL TANKS CAPACITY 1500 L
TRANSFER PUMP
QUANTITY: 1

10. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 3000MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR -FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
DIMENSIONS LENGTH 65000 MM X WIDTH 43000 MM X HEIGHT 25000 MM
INSTALLED ELECTRIC POWER: 3 X 63 A
QUANTITY: 1(NO 54)

11. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 1600MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
THE HYDRAULIC SYSTEM HAS FAILED/NOT WORKING
DIMENSIONS LENGTH 5,300 CM X WIDTH 4,300 CM X HEIGHT 2,500 CM
QUANTITY: 1(NO 53)

15. INSPECTION MACHINE
MONFORTS
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

16. MACHINE FOR BONDING PIECES (GOODS)
GEBRUDER DOHLE
MODEL: 799/03
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 2

18. WINDING MACHINE
MARK: AEG
TECHNICAL INFORMATION:
WINDING GOODS
QUANTITY: 1

19. INSPECTION MACHINE
MONFORTS
MODEL: MBH
YEAR: 1977
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

20. MEASURING WINDING MACHINE
MENZEL
MODEL: MWE2
YEAR: 1986
TECHNICAL INFORMATION:
WINDING DIFFERENT LENGTHS OF GOOD
QUANTITY: 1

21. HEAT EXCHANGER
PT-S
YEAR: 2002
TECHNICAL INFORMATION:
RECUPERATION
QUANTITY: 1

23. DOUBLING MACHINE
MODEL: MLH
YEAR: 1975
TECHNICAL INFORMATION:
DOUBLING AND COMPOUNDING GOODS
QUANTITY: 1

YARN DYEING AND DRYING:
1. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN : MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
QUANTITY: 2 PCS (NO 12, NO 14)

2. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 850
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY;
6 INCHES BOBBIN : MAX 144 KG, MIN. 58 KG
5 INCHES BOBBIN : MAX 100 KG, MIN. 42 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
THICKNESS OF PLATE = 30 CM
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2.00 CM
DIMENSIONS: LENGTH 3100MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
INSTALLATION OF THE SOIL = 60CM DEEPER
(APPLY TO ALL INSTALLATION)
QUANTITY: 1(NO 18)

3. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS TYPE 600
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN: MAX 84 KG, MIN. 34 KG
5 INCHES BOBBIN: MAX 59 KG, MIN. 26 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
DIMENSIONS: LENGTH 2500MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC POWER: 17 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
QUANTITY: 1(NO 16)

4. PRESSURE DRYING APPARATUS – TANDEM
JASPER
YEAR: 1998
TECHNICAL INFORMATION:
DIMENSION: LENGTH 290CM WIDTH 3300MM X HEIGHT 1800MM X HEIGHT 2900MM
CUPBOARD FOR ELECTRONICS
LENGTH 250CM X WIDTH 60CM
QUANTITY: 2 TANDEM WORKING AS ONE UNIT

5. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN: MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 98˚ C
PRESSURE: UP TO 4.5 BAR
MANUAL PROCESSOR
DIMENSIONS: LENGTH 2800MM X WIDTH 3100MM X HEIGHT 2500MM X HEIGHT 2900MM
(WITH A DOSING DEVICE IN THE FORM OF "V")
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS: LENGTH 2500MM X WIDTH 60MM
QUANTITY: 1 (NO 13)

6. DYEING APPARATUS
THEN
MODEL: HL 40/7,8
YEAR: 1986
WIDTH: 1800MM
5 INCHES BOBBIN: MAX 12 PIECES
WORKING TEMPERATUR: UP TO 140˚ C
HEIGHT: 2160MM
PRESSURE: UP TO 4,5 BAR
INSTALLED ELECTRIC POWER – 3X16 A
TECHNICALINFORMATION: DYEING APPARATUS
DIMENSIONS: LENGTH 1600MM
QUANTITY: 1

7. THE LOADING AND UNLOADING DEVICE
JASPER
YEAR: 1998
TECHNICAL INFORMATION; LOADING DEVICE FOR BOBBINS
THICKNESS OF PLATE = 300MM (APPLY TO ALL INSTALLATIONS)
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2000MM (APPLY TO ALL INSTALLATION)
DIMENSIONS : Ø 1700MM : HEIGHT1600MM
INSTALLED ELECTRIC POWER : 10KW
QUANTITY: 1

8. BRIDGE CRANE
TECHNICAL INFORMATION:
THE CARGO TRANSFER
QUANTITY : 2

9. PROCESS WATER REGENERATION + TANK
JASPER
TECHNICAL INFORMATION:
STORAGE OF WATER FOR THE PRODUCTION PROCESS
QUANTITY : 1

SEWING:
8. SEWING MACHINE FOR WASHING GLOVES
TEXPA ARBTER
MODEL: WASCHLA 10
YEAR: 1994
TECHNICAL INFORMATION:
SEWING WASHING GLOVES, FITTING LABELS AND CORD.
QUANTITY: 1

9. CONTROL TABLES
TECHNICAL INFORMATION:
GOOD INSPECTION AND WEIGHING
QUANTITY: 3

10. PACKING MACHINE
BECK
TECHNICAL INFORMATION:
PACKING TOWELS INTO FOIL
QUANTITY: 1

3. WINDING MACHINE
SCHLAFHORST
MODEL: BKN
YEAR: 1975
TECHNICAL INFORMATION:
96 PIECES SPINDLES (2 X 48 SPINDLES)
QUANTITY: 2

4. MOBILE REGALS FOR YARN STORAGE
INCLUDED SELLING YARN
QUANTITY: 3

WARPING AND WEAVING:
1. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
HACOBA
MODEL: USK T1000/SM
YEAR: 1990
TECHNICAL INFORMATION:
ELEKTRONIC COMPUTER, AUTOMATIC SETTING OF CONE,
DEVICE FOR CROSSING THE FLOOR DIVISION THREADS
PRELIMINARY SETTING : OF LENGTH IN METERS (YARN LEGTH RECORDER), NUMBER OF REVOLUTIONS, …
CONE CREEL/CREELS 2 X 32 CROSS-WOUND COME (MAX. DIAMETER CROSS-WOUND IS 225 MM)
WETTING TROUTH FOR COLD STARCHING BY APPLICATOR ROLLER
MAXIMUM WARPING WIDTH : 240 CM/ WARPING WIDTH (MARKED) 240 CM
QUANTITY: 1

2. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
SUCKER MÜLLER HACOBA
MODEL: USK -S/SM
YEAR: 1998
TECHNICAL INFORMATION:
MAXIMUM WARPING WIDTH : 2000MM
QUANTITY: 1

3. WARPING MACHINE
BENNINGER
MODEL: 97126 FB
YEAR: 1978
TECHNICAL INFORMATION:
MAX. NUMBER OF CONES 704
QUANTITY: 1

4. SIZING MACHINE
BENNINGER ZELL
MODEL: BZ-7M
YEAR: 1975
TECHNICAL INFORMATION:
MAXIMUM WORKING WIDTH 2400MM
TOTAL BEAM 8 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
SIZING KITCHEN
QUANTITY: 1

5. SIZING MACHINE
BENNINGER ZELL
MODEL: XK Z6F
YEAR: 1986
TECHNICAL INFORMATION:
MAX. WORKING WIDTH 240 CM
TOTAL BEAM 12 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
QUANTITY: 1

13. COMPRESSOR FOR COMPRESSED AIR
KAESER
MODEL: CS 76, ABT 72
YEAR: 2003
NO. OF MASHINES: 3

14. KNOTTING MACHINE
KNOTEX
MODEL: AS/2 8013 EA03
YEAR: 2002
TECHNICAL INFORMATION:
WITH TWO TROLLEY SIZE 2500MM
QUANTITY: 5

15. ELEVATOR FOR BEAMS
GENKINGER
MODEL: EE-KHHR
YEAR: 1998
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

16. ELEVATOR FOR BEAMS
HUBTEX
MODEL: KHHW
YEAR: 1988
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

17. PUNCH MACHINE
GROSSE
MODEL: LSE 600
YEAR: 1998
TECHNICAL INFORMATION:
PUNCHING CARDS
QUANTITY: 1

18. ELEVATOR FOR BEAMS
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

19. MOBILE REGALS FOR BEAM STORAGE
TECHNICAL INFORMATION:
UP - DOWN MOVING REGALS
QUANTITY: 13

WEAVING SAURER 1;2;3;4:
1. STÄUBLI JACQUARD
WITH 560 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 10

2. STÄUBLI JACQUARD
WITH 768 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 4

3. STÄUBLI JACQUARD
WITH 1120 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

4. STÄUBLI JACQUARD
WITH 912 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MASHINES: 1

WEAVING SILK:
1. WEAVING MACHINE
SOMET
MODEL: MASTER SM93
YEAR OF CONSTRUCTION: 1990
TECHNICAL INFORMATION:
WITH STÄUBLI JACQUARD, JC4 CONTROLLER
5-6 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

2. CONTROL TABLE
TECHNICAL INFORMATION:
GOOD INSPECTION
NUMBER OF MACHINES: 1

READY MADE DEPARTMENT FOR TERRY BATHROBES:
1. CUTTING TABLE
BULLMERWERK
MODEL: KOMET II
TECHNICAL INFORMATION:
CUTTING GOODS BY CUTTING PATTERNS FOR TERRY
BATHROBES
QUANTITY: 1

2. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
QUANTITY: 2

3. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

5. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
TRIPLE STICH OVERLOK
QUANTITY: 1

6. SEWING MACHINE
LEWIS
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
BLIND STICH
QUANTITY: 1

7. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

8. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY PRODUCTS
OVERLOK
QUANTITY: 2

9. SEWING MACHINE
MAUSER SPECIAL
TECHNICAL INFORMATION:
SEWING NAPKINS
OVERLOK
QUANTITY: 1

10. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

11. SEWING MACHINE
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 1

12. SEWING MACHINE
NECCHI
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR
BONDING GOODS
QUANTITY: 4

13. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

14. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

LABOR MACHINES:
1. APPARATUS FOR MEASURING ZTWIST, TURN/ROLL - TORSIOMETER
MARK: CALDERARA BOSI
YEAR: 1989
QUANTITY: 1

2. APPARATURS FOR MEASURING THE FRICTION COEFFICIENT -
ZWEIGLE
MODEL: µ-METER G 530
TYPE: 530
YEAR: 1972
TECHNICAL INFORMATION:
NOT WORKING
QUANTITY: 1

3. LIGHTING CHAMBER

MARK: DATACOLIR INTERNATIONAL
YEAR: 2004
TECHNICAL INFORMATION:
FROM 4 TYPES OF LIGHT ONLY WORKS 1
QUANTITY: 1

4.AA WINDING APPARATURS FOR THE DYEING TUBE THE SAMPLING DEVICE
ZWEIGLE (REUTLIGEN)
QUANTITY: 1

5. WINDING APPARATURS FOR COLOR STANDARDS
IZDELANO V SVILANITU
YEAR: 2001
QUANTITY: 1

6. YARN DYEING APPARATURS PRETEMA MULTICOLOR
PRETEMA
MODEL: TYPE MC-320
YEAR: 1982
TECHNICAL INFORMATION:
V 22 W 1800
DIMENSIONS: LENGTH 119 CM X WIDTH 61 CM X HEIGHT 126 CM
INSTALLED ELECTRIC POWER: 1800 W
QUANTITY: 1

7. DYNAMOMETER FOR SPINNING
KARL SCHRÖDER
YEAR: 1977
QUANTITY: 1

8. SPEKTROFOTOMETER DATACOLOR INTERNATIONAL
DATACOLOR INTERNATIONAL
MODEL: SPECTRAFLASH SF600 PLUS CT
YEAR: 1999
TECHNICAL INFORMATION:
RATINGS: 100-240 V ̴47-63 HZ, 100 VA
NOT WORKING (DO NOT KNOW THE TYPE OF TROUBLE)
QUANTITY: 1

9. APPARATURS FOR THE VISUAL APPEARANCE OF THE YARN
ZWEIGLE KG REITLINGEN
QUANTITY: 1

QUANTITY: 1 COMPLETE PLANT

Learn More

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

REFERENCE NUMBER: M-1769 (660VSYKXX5) FROZEN FRENCH FRIES PRODUCTION LINE CAPACITY FROM 100KG PER HOUR TO 1200KG PER HOUR, EVEN LARGER CAPACITY AVAILABLE FRYING MACHINE CAPACITY IS 300 TO 500KG PER HOUR QUANTITY AVAILABLE: 1 Learn More

TT-2177 GAS BASED COMBINED CYCLE POWER PLANT, 116 MW, YEAR 2021 GENERAL ELECTRIC GAS TURBINE GAS TURBINE MODEL NUMBER: GE, 6FAG QUANTITY: 1 Learn More

TT-1316 NONWOVEN MIDDLE SPEED NEEDLE LOOM, WORKING WIDTH 3200mm MACHINE STRUCTURE FEATURES: 1. SPLICING TYPE STRUCTURE, IT IS MADE BY HIGH QUALITY Q235 STEEL PLATE WELDING, THEN FINE TEMPERING QUALITATIVELY WITH SUFFICIENT COMPLETENESS AND STABILITY. UPPER AND DOWN MACHINE GIRDERS BOTH PRECISELY PROCESSING MACHINED. 2. ECCENTRIC BEARINGS ADOPT TORRINGTON FAMOUS BRAND 3. MAIN SHAFT IS USING 42CROMO MATERIAL. AFTER CONDITIONING TREATMENT FINE FINISHING AND GRINDING. 4. NEEDLE GIRDER HIGH SPEED TURBINE ELECTRIC LIFTING, STRIPPER PLATE TURBINE ELECTRIC LIFTING, NEEDLE GIRDER ROLLER SCALE DISPLAY. AIR LOCKED THE NEEDLE PLATE TIGHTLY. 5. NEEDLE PLATE LUOYANG MADE BY MAGNESIUM ALLOY DIE CASTING PLATE COMPOSITE PU, RADON ARRANGE NEEDLES HOLE φ1.82mm 6. INPUT PVC LATTICE, OUTPUT ROLLER ADOPTS φ155mm, HIGH QUALITY SEAMLESS STEEL PIPE, AFTER FINISHING GRINDING, THE SURFACE IS PLATED WITH HARD CHROME, UPPER ROLLER ADJUSTABLE HEIGHT AIR CYLINDER. 7. MAIN MOTOR, OUTPUT ROLLER ALL FREQUENCY CONTROL. 8. INSTALLED POWER: AROUND 15.5KW, MAIN MOTOR 11 KW. QUANTITY: 1 SET Learn More

REFERENCE NUMBER: M-5195 (13131QTBS12RC) L PICANOL OMNI 4-R AIRJET WITH 4 COLORS YEAR 1995 WIDTH 2200mm PICANOL OMNI 4 R AIRJET WIDTH 2200mm 4 COLORS STAUBLI ELECTRONIC DOBBY 2580 / RS16 / 10 / 10 YEAR 1995 ELECTRONIC DOBBY STAUBLI 2580RS 16/10/10 YEAR 1995 QUANTITY AVAILABLE: 3 Learn More

TT-6624 MINI SUGAR CRUSHER PLANT, 200 TCD, YEAR 2019 1. MINI SUGAR CRUSHER PLANT 2. 200 TCD 3. MANUFACTURING YEAR 2019 4. PLANT RUNNING 2020 5. PLANTS RUNNING OVER 180 DAYS Learn More